Calibration | NCR 7870 specs

5-2 Chapter 5: Calibration

The calibration procedure sets the Load Cell and the electronics to interpret the weight of an item accurately. You can calibrate the scale after power has been supplied for 30 minutes if the ambient air conditions have been 20° C (68° F) for at least 24 hours. If the ambient air conditions have not been met, then the scale must be on for at least 6 hours before you can calibrate it. One or more certified weight sets are required to calibrate and certify the scale.

•Whole Pound Weight Set: NCR Part Number 998-0633009

•Fractional Pound Weight Set: NCR Part Number 998-0633012

•Kilogram Weight Set: Obtain locally

The EEPROM on the Scale Board maintains an audit trail of scale calibration and weigh parameter setting. The audit trail consists of two event counters. You can display the audit trail count by pressing and holding the Scale Zero button on the Operator Display Panel. The display alternates between Cal xxx and PAr xxx. The Cal value is the number of times the scale has been calibrated. The PAr value is associated with the weigh parameter setting and should never change.

Note: The audit trail can be displayed only on units with the Integrated Display or with the NCR 7825 Remote Display.

Image 88

NCR 7870 manual Calibration

Contents

Users Guide Page Table of Contents Site Preparation Users Guide Installation Calibration Operation Programming Users Guide Viii Users Guide Troubleshooting Appendix a Programming Worksheets Revision Record Radio Frequency Interference Statements Federal Communications Commission FCCCanadian Department of Communications Voluntary Control Council For Interference Vcci Mark Applicability Scale Regulatory Declaration of Conformity This Directive is not applicable to NCR 7870-1000 or NCR Scale Identification Label NCR Corporation Laser Safety Laser Safety Label Country Language Specific IEC Class 1 Laser Labels Laser Power Laser Module Label Microwatts Milliwatts Introduction About the NCR 7870 Scanner/Scale Models Common Features Reading the Product Number 7870-1000-9090 7870-2000-90907870-3000-9090 7870-4000-9090 General Features and Functions Bar Code Recognition Decode Features Mode 1 Inquiry ModeBi-Optic Scanning Pacesetter Plus Mode 2 Real-Time Mode Mode 3 Operations ModeDisplays NCR 7825 Remote Display Integrated Display Power Supply Interface TypesLaser Scanner No Display Programming Sizes section in Site Preparation Scale Certifications Soft Power Down Scanner Power RequirementsScan Zone Top Plates Top Plates and Scan WindowsSlot Scanner Window Side Scanner Window Scale Features and Functions Scale Functions and FeaturesReset / Scale Zero Load Cell Kits Kit Name Kit Type Available for Kit Name Kit Type Available for Kit Name Kit Type Available for Chapter Kit Name Kit Type Available for Kit Name Kit Type Available for Features, Functions, and Kits Site Preparation Getting Started Site Preparation About Site Preparation Site Preparation Customer Responsibilities Operating Range Environmental RequirementsExtreme Operating Range Storage Range Transit Range Checkstand Power and Wiring Considerations Power ConsiderationsPower Applications Power Transients Protection Wiring Considerations Canadian, and Japanese Checkstand Wiring European Checkstand Wiring 220Vac Store International Checkstand Wiring Running Feeder Lines from Main Service Panel Wiring InstructionsCircuit a Circuit B Circuit C Checkstand Considerations Ventilation Requirements Service Clearance Display Clearance Item Diverter Checkstand Hole Checkstand Hole Models 1000 NCR 7870-1000 Scanner Checkstand Hole Models 3000, 4000 NCR 7870 3000 Scanner DC Power Cable Power Supply to Cable Lengths and Hole SizesCable Hole Diameters Minimum Hole Diameter 1.52 cm 0.60 AC Power Cords Outlet to Power Supply Remote Display CablesMinimum Hole Diameter 3.18 cm 1.25 Minimum Hole Diameter 1.90 cm 0.75 Interface Cables NCR Host Terminals Host Interface Cable Corporate Part Length Terminal Number Interface Cables NCR Host Terminals Interface Cables Casio Host Terminals Interface Cables Epson Host Terminals Interface Cables Data Checker Host TerminalsInterface Cables Gilbarco Host Terminals Interface Cables IBM Host Terminals Interface Cables ICL Host Terminals Interface Cables Microbilt Host Terminals Interface Cables NEC Host Terminals Interface Cables Sasi Host Terminals NCR 7870 Dimensions NCR 7870 1000 DimensionsNCR 7870 2000 Dimensions NCR 7870-1000 & 2000 Models NCR 7870 3000 Dimensions NCR 7870-3000 Model NCR 7870 4000 & 4500 Dimensions NCR 7870-4000 & 4500 Models Reporting a Damaged Unit What’s in the Box Cable Verification Checkstand Verification Install Cables Installing Unit in CheckstandInstructions Single Cable Set-Up Dual Cable Set-Up Datachecker or RS-232 Cable Set-Up Tower Subplate Assembly Cover/Lift Strap If the NCR 7870 Does Not Pass Level O Diagnostics Determining if the Unit is OperationalNCR 7870-1000 and 3000 Scanners NCR 7875-2000, 4000, and 4500 Scanner/Scales Checkout Reading Operation Determining Communications Protocol Scale Address for IBM Installation Calibration General Calibration Calibration Procedure Exercising the ScaleTools Instructions Accessing the Calibration Switch Remove screw securing Lift Strap to unit 11040 Connecting the Field Service Calibration Display Go to Performing the Calibration Performing the Calibration Display Add Weight Remove Weight Verifying Calibration Procedure 1 Increasing Load Test Select the appropriate weight feature from the table below Procedure 2 Over-Capacity Test Procedure 3 Decreasing Load Test Procedure 4 Shift Test Securing the Calibration Switch Prior Steps Calibration Calibration Operation Status Indicators About Using the Operator ControlsScan Windows Reset / Scale Zero Button Motion DetectorAudible Tone Voice Messages About Using the Scanner Proper Label Orientation Active Scan Zone Multiple Reads Bar Code Quality Power Up Operating InstructionsScanner Only Models Scanner/Scale Models Scanning Procedure Not-On-File Error Weighing Procedure Changing the Good Read Tone Routine Maintenance Operation Programming Programming How to Program the NCR Creating the ProgramWriting the Program Entering the Program Scan the Save and Reset Tag Save the Program Programming Mode NormalNormalOperatingOperatingModeMode Programming Tags Abort Default EndHex 0 Hex F Function Programming Mode Save and Reset Program Entry Example Scan the Programming Mode tagEnter All Parameters Enter Specific Parameters Base Programming State Ar C odes Code Programming Tips Defaults Program Parameter DescriptionsCommunications Protocol Specific Program Parameters Ocia Non NCR Dual Cable Hex Ocia NCR Long HexIBM 468x/9x Port 4A Slot Scanner Hex 3 tag IBM 468x/9x Port 4B Hhbcr Hex 4 tag RS-232 Hex 5 tagOcia Single Cable Hex 6 tag Ocia NCR Dual Cable Hex 7 tag IBM 1520 BRC, IBM 468x/9x Port 4B Hex B tag Casio 4-Bit, Parallel, Dual Cable Hex a tagTEC, 4-Bit, Parallel, Dual Cable Hex C tag Communications Protocol Hex Tag Summary Programming ExampleYour Program Good Read Tone Not On File Tone VolumeTone Frequency Hertz Tone Volume Program ExampleTone Length Milliseconds Tone On/Off Lockout Timer Milliseconds TimersRestart Lockout Timer Active Time Minutes Bar Codes Version D Extend UPC-A to EAN-13 Extend UPC-E to UPC-APeriodic Codes Periodic Code Extension 0 0 1 2 Send Data Code Minimum Characters Allowed Full Ascii Check Digit PresentTransmit Check Digit Allow 1- or 2-Character Tags Ascii Interleaved 2 Bar Code Length Value 1 4 1 0 Minimum Data Characters Allowed UCC Bar Codes Minimum Data Characters Allowed UCC Label Identifiers Identifier Type Common Byte 1 and Common Byte Common Byte Bar Code TypeUnique Identifier Version Number UPC-D Only Label Identifier Baud Rate RS-232 ParametersParity Stop Bits and Character Length Handshake RS-232 Parameters Baud Rate Parity BCC Options Interface Control Check Digit RS-232 Parameters BCC Interface Options Control Check Digit Prefix Byte RS-232 Prefix ByteAscii Code RS-232 Prefix Byte RS-232 Terminator Byte Terminator Byte RS-232 Terminator Byte Message Delay Normal or Eavesdrop ModeRS-232 Communications Options Scanner or Scanner/Scale Format Beep at Scale Weight Transmission RS-232 Model Number Scale ParametersIBM Address 995 kg / 13.995 kg Second Weight Display Timer Miscellaneous Parameters Ocia Blank Display In Price Mode IBM Tone Control Good Read ToneOcia Price Display IBM Rexmit Control Enable/Disable Voice Messages IBM Tag Data Format 11822 Mode 1 Inquiry Pacesetter Plus Information Mode 2 Real Time 1136 Codes Description Mode 3 Normal OCH, xyH, xzH 43H, 3yH, 3zH OCH, 0yH, 0zH Decoding was difficult. May be due to Examples of Host Access to Tallies Host Access to TalliesExample An IBM host terminal request for tally C1 0DH C1H Host Reset of Tallies C5H C0H Delay Weight Data to IBM Host Terminal Special Programming EAN/JAN/UPC Multi-Symbol Scanning Parameters Label ConstructionSingle Label Restriction Transmitting Label Data Hex a tag and the Save and Reset tag Programming Early Beep Disable Good Read Tone Presets Preset Good Weigh Tone When Transmitting Data Terminal Coupon Interface Parameters HexHex a Hex B Hex C Hex D Coupon Select 2 Parameter Disable Enable Ascii Code Chart 1A SUB 1B ESC 1C FS 1D GS 1E RS 1F US Programming Troubleshooting Fault Identification Scanner Troubleshooting Chart Scale Troubleshooting Chart Scan the Diagnostic Mode tag Voice Messages Troubleshooting ChartScan Programming Mode tag Troubleshooting Format PurposeShortcuts Hex Characters DefaultsProgram Entry Timers Communications ProtocolGood Read Tone Bar Codes-1 Bar Codes-3 Bar Codes-4Label Identifiers RS-232 Parameters-1 RS-232 Prefix Byte RS-232 Terminator ByteRS-232 Communications Options Scale Parameters Worksheets Communications Protocol Good Read Tone Timers BAR Codes BAR Codes BAR Codes Code Label Identifiers RS-232 Parameters Appendix a Programming Worksheets A-15 RS-232 Prefix Byte RS-232 Terminator Byte RS-232 Communications Options Scale Parameters Miscellaneous Parameters Appendix a Programming Worksheets A-21 Appendix a Programming Worksheets Index Scanner/Scale Index-3 Slot Scan Window Index-5 Business Reply Mail BST0-2121-90 Nov Printed on recycled paper