Cable Lengths and Hole Sizes, Cable Hole Diameters | NCR 7870

Chapter 3: Site Preparation 3-21

Cable Lengths and Hole Sizes

When selecting a cable, take care to choose one with enough length for easy routing to the NCR 7870. Also, include enough slack to allow the unit to be lifted from the cutout without disconnecting the cables. This will be beneficial while servicing the unit.

Minimum hole size data is provided for making openings to pass cables through the checkstand. Ensure after drilling that there are no sharp edges which may damage the cable.

The following charts provide cable length and hole size data for AC Power Cords, DC Power Cables, Interface Cables, and Remote Display Cables. The NCR 7870 can connect to any NCR Retail Terminal as well as many competitive host terminals so a comprehensive list of interface cables has been provided.

Cable Hole Diameters

Cable	Minimum Hole Size

Power Cord – Outlet to Power Supply	3.18 cm (1.25 in.)

Power Cable – Power Supply to 7870	1.52 cm (0.60 in.)

Interface Cable	1.90 cm (0.75 in.)

Remote Display Cable	1.90 cm (0.75 in.)

DC Power Cable – Power Supply to 7870

Minimum Hole Diameter: 1.52 cm (0.60 in.)

Cable	Cable Length

DC Power Cable	1.22 Meters (4 Feet)

Note: DC Power Cable length is not a factor if the Power Supply is mounted on the chassis of the 7870 (Models 1000 and 2000 only).

Image 63

NCR 7870 manual Cable Lengths and Hole Sizes, Cable Hole Diameters, DC Power Cable Power Supply to

Contents

Users Guide Page Table of Contents Site Preparation Users Guide Calibration Installation Operation Programming Users Guide Viii Users Guide Appendix a Programming Worksheets Troubleshooting Revision Record Voluntary Control Council For Interference Vcci Radio Frequency Interference StatementsFederal Communications Commission FCC Canadian Department of Communications Scale Regulatory Mark Applicability This Directive is not applicable to NCR 7870-1000 or NCR Declaration of Conformity NCR Corporation Scale Identification Label Laser Safety Label Laser Safety Country Language Specific IEC Class 1 Laser Labels Laser Module Label Laser Power Milliwatts Microwatts Introduction Models About the NCR 7870 Scanner/Scale Reading the Product Number Common Features 7870-4000-9090 7870-1000-90907870-2000-9090 7870-3000-9090 Bar Code Recognition General Features and Functions Pacesetter Plus Decode FeaturesMode 1 Inquiry Mode Bi-Optic Scanning NCR 7825 Remote Display Mode 2 Real-Time ModeMode 3 Operations Mode Displays Integrated Display No Display Power SupplyInterface Types Laser Scanner Sizes section in Site Preparation Programming Scale Certifications Scanner Power Requirements Soft Power DownScan Zone Top Plates and Scan Windows Top PlatesSlot Scanner Window Side Scanner Window Load Cell Scale Features and FunctionsScale Functions and Features Reset / Scale Zero Kit Name Kit Type Available for Kits Kit Name Kit Type Available for Kit Name Kit Type Available for Chapter Kit Name Kit Type Available for Kit Name Kit Type Available for Features, Functions, and Kits Site Preparation Getting Started Site Preparation About Site Preparation Site Preparation Customer Responsibilities Environmental Requirements Operating RangeExtreme Operating Range Transit Range Storage Range Power Transients Protection Checkstand Power and Wiring ConsiderationsPower Considerations Power Applications Canadian, and Japanese Checkstand Wiring Wiring Considerations 220Vac Store European Checkstand Wiring International Checkstand Wiring Wiring Instructions Running Feeder Lines from Main Service PanelCircuit a Circuit C Circuit B Ventilation Requirements Checkstand Considerations Service Clearance Item Diverter Display Clearance Checkstand Hole NCR 7870-1000 Scanner Checkstand Hole Models 1000 NCR 7870 3000 Scanner Checkstand Hole Models 3000, 4000 Minimum Hole Diameter 1.52 cm 0.60 DC Power Cable Power Supply toCable Lengths and Hole Sizes Cable Hole Diameters Minimum Hole Diameter 1.90 cm 0.75 AC Power Cords Outlet to Power SupplyRemote Display Cables Minimum Hole Diameter 3.18 cm 1.25 Host Interface Cable Corporate Part Length Terminal Number Interface Cables NCR Host Terminals Interface Cables NCR Host Terminals Interface Cables Casio Host Terminals Interface Cables Data Checker Host Terminals Interface Cables Epson Host TerminalsInterface Cables Gilbarco Host Terminals Interface Cables ICL Host Terminals Interface Cables IBM Host Terminals Interface Cables NEC Host Terminals Interface Cables Microbilt Host Terminals Interface Cables Sasi Host Terminals NCR 7870-1000 & 2000 Models NCR 7870 DimensionsNCR 7870 1000 Dimensions NCR 7870 2000 Dimensions NCR 7870-3000 Model NCR 7870 3000 Dimensions NCR 7870-4000 & 4500 Models NCR 7870 4000 & 4500 Dimensions What’s in the Box Reporting a Damaged Unit Checkstand Verification Cable Verification Installing Unit in Checkstand Install CablesInstructions Single Cable Set-Up Dual Cable Set-Up Datachecker or RS-232 Cable Set-Up Tower Subplate Assembly Cover/Lift Strap NCR 7875-2000, 4000, and 4500 Scanner/Scales If the NCR 7870 Does Not Pass Level O DiagnosticsDetermining if the Unit is Operational NCR 7870-1000 and 3000 Scanners Checkout Reading Operation Determining Communications Protocol Scale Address for IBM Installation General Calibration Calibration Instructions Calibration ProcedureExercising the Scale Tools Accessing the Calibration Switch Remove screw securing Lift Strap to unit 11040 Connecting the Field Service Calibration Display Go to Performing the Calibration Performing the Calibration Display Add Weight Remove Weight Verifying Calibration Select the appropriate weight feature from the table below Procedure 1 Increasing Load Test Procedure 2 Over-Capacity Test Procedure 3 Decreasing Load Test Procedure 4 Shift Test Prior Steps Securing the Calibration Switch Calibration Calibration Operation About Using the Operator Controls Status IndicatorsScan Windows Voice Messages Reset / Scale Zero ButtonMotion Detector Audible Tone Proper Label Orientation About Using the Scanner Multiple Reads Active Scan Zone Bar Code Quality Scanner/Scale Models Power UpOperating Instructions Scanner Only Models Not-On-File Error Scanning Procedure Weighing Procedure Changing the Good Read Tone Routine Maintenance Operation Programming Programming Entering the Program How to Program the NCRCreating the Program Writing the Program Save the Program Scan the Save and Reset Tag NormalNormalOperatingOperatingModeMode Programming Mode Abort Programming Tags Function DefaultEnd Hex 0 Hex F Save and Reset Programming Mode Scan the Programming Mode tag Program Entry ExampleEnter All Parameters Base Programming State Enter Specific Parameters Ar C odes Code Programming Tips Specific Program Parameters DefaultsProgram Parameter Descriptions Communications Protocol Ocia NCR Long Hex Ocia Non NCR Dual Cable HexIBM 468x/9x Port 4A Slot Scanner Hex 3 tag Ocia NCR Dual Cable Hex 7 tag IBM 468x/9x Port 4B Hhbcr Hex 4 tagRS-232 Hex 5 tag Ocia Single Cable Hex 6 tag Casio 4-Bit, Parallel, Dual Cable Hex a tag IBM 1520 BRC, IBM 468x/9x Port 4B Hex B tagTEC, 4-Bit, Parallel, Dual Cable Hex C tag Programming Example Communications Protocol Hex Tag SummaryYour Program Not On File Tone Volume Good Read ToneTone Frequency Hertz Tone On/Off Tone VolumeProgram Example Tone Length Milliseconds Timers Lockout Timer MillisecondsRestart Lockout Timer Active Time Minutes Version D Bar Codes Periodic Code Extension Extend UPC-A to EAN-13Extend UPC-E to UPC-A Periodic Codes Send Data 0 0 1 2 Minimum Characters Allowed Code Allow 1- or 2-Character Tags Full AsciiCheck Digit Present Transmit Check Digit Ascii Interleaved 2 Value 1 Bar Code Length 4 1 0 UCC Minimum Data Characters Allowed Bar Codes Minimum Data Characters Allowed UCC Label Identifiers Identifier Type Common Byte 1 and Common Byte Bar Code Type Common ByteUnique Identifier Version Number UPC-D Only Label Identifier RS-232 Parameters Baud RateParity Handshake Stop Bits and Character Length RS-232 Parameters Baud Rate Parity Interface Control BCC Options Check Digit RS-232 Parameters BCC Interface Options Control Check Digit RS-232 Prefix Byte Prefix ByteAscii Code RS-232 Prefix Byte Terminator Byte RS-232 Terminator Byte RS-232 Terminator Byte Normal or Eavesdrop Mode Message DelayRS-232 Communications Options Scanner or Scanner/Scale Format Beep at Scale Weight Transmission RS-232 Scale Parameters Model NumberIBM Address 995 kg / 13.995 kg Miscellaneous Parameters Second Weight Display Timer IBM Rexmit Control Ocia Blank Display In Price ModeIBM Tone Control Good Read Tone Ocia Price Display IBM Tag Data Format Enable/Disable Voice Messages 11822 Pacesetter Plus Information Mode 1 Inquiry 1136 Mode 2 Real Time Codes Description OCH, xyH, xzH 43H, 3yH, 3zH OCH, 0yH, 0zH Mode 3 Normal Decoding was difficult. May be due to Host Access to Tallies Examples of Host Access to TalliesExample An IBM host terminal request for tally C1 0DH C1H C5H C0H Host Reset of Tallies Special Programming Delay Weight Data to IBM Host Terminal Transmitting Label Data EAN/JAN/UPC Multi-Symbol Scanning ParametersLabel Construction Single Label Restriction Hex a tag and the Save and Reset tag Programming Early Beep Disable Preset Good Read Tone Presets Good Weigh Tone When Transmitting Data Hex C Hex D Terminal Coupon Interface ParametersHex Hex a Hex B Coupon Select 2 Parameter Disable Enable 1A SUB 1B ESC 1C FS 1D GS 1E RS 1F US Ascii Code Chart Programming Fault Identification Troubleshooting Scanner Troubleshooting Chart Scale Troubleshooting Chart Voice Messages Troubleshooting Chart Scan the Diagnostic Mode tagScan Programming Mode tag Troubleshooting Purpose FormatShortcuts Defaults Hex CharactersProgram Entry Bar Codes-1 TimersCommunications Protocol Good Read Tone RS-232 Parameters-1 Bar Codes-3Bar Codes-4 Label Identifiers Scale Parameters RS-232 Prefix ByteRS-232 Terminator Byte RS-232 Communications Options Communications Protocol Worksheets Good Read Tone Timers BAR Codes BAR Codes BAR Codes Code Label Identifiers RS-232 Parameters Appendix a Programming Worksheets A-15 RS-232 Prefix Byte RS-232 Terminator Byte RS-232 Communications Options Scale Parameters Miscellaneous Parameters Appendix a Programming Worksheets A-21 Appendix a Programming Worksheets Index Scanner/Scale Index-3 Slot Scan Window Index-5 Business Reply Mail BST0-2121-90 Nov Printed on recycled paper