2.3 Names and Locations
| Switch Position | Operation | ||
|
|
|
|
|
7 |
| 1 2 3 4 |
|
|
0 |
|
| Initialises all ACD Report settings. | |
| 1 |
|
| |
|
|
| ||
|
|
|
|
|
|
|
|
| |
|
|
|
| Initialises the VPS. For |
|
|
|
| initialised. All settings are reset to their default values. Recorded |
8 | 1 2 3 4 |
| messages and customised prompts are erased. All System Prompts | |
0 |
|
| are reset to their defaults. | |
| 1 |
|
| |
|
|
| ||
|
|
|
|
|
|
| CAUTION |
|
|
|
|
|
|
| All |
|
|
|
|
|
|
|
|
9 |
|
|
|
|
|
| Reserved |
|
|
|
|
|
|
|
|
|
| 1 2 3 4 |
|
| |||
10 |
|
| Puts the VPS in APT Integration mode. Auto Configuration starts and all | ||||
0 |
|
|
|
|
| ||
| 1 |
|
|
|
|
| ports are set to provide Automated Attendant service. |
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| 1 2 3 4 |
| ||||
11 |
|
| Puts the VPS in APT Integration mode. Auto Configuration starts and all | ||||
0 |
|
|
|
|
| ||
| 1 |
|
|
|
|
| ports are set to provide Voice Mail service. |
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
12 |
| 1 2 3 4 |
| Primary Language will be set to use Language 1 prompts.*1 | |||
0 |
|
|
|
|
| ||
| 1 |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
13 |
| 1 2 3 4 |
| Primary Language will be set to use Language 2 prompts.*1 | |||
0 |
|
|
|
|
| ||
| 1 |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
14 |
| 1 2 3 4 |
| Primary Language will be set to use Language 3 prompts.*1 | |||
0 |
|
|
|
|
| ||
| 1 |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
15 |
|
|
|
|
|
| Reserved |
|
|
|
|
|
|
|
|
*1 | If the selected language has no prompts, no prompts will be heard. | ||||||
When setting the Mode Switch to any position (except 0):
1.Disconnect the port cables from the VPS.
2.Turn the power switch off.
3.Set the Mode Switch.
4.Turn the power switch back on.
5.Connect the port cables.
6.Confirm that the Run Indicator blinks the same number of times as the Mode Switch position (e.g., 5 blinks for switch position 5, etc.).
•This may take several minutes. The Alarm Indicator and Run Indicator will first blink intermittently before the Run Indicator blinks to indicate the Mode Switch position.
7.Turn the power switch off at the VPS.
8.Set the Mode Switch to position 0.
9.Turn the power switch back on at the VPS.
Installation Manual
39
