DTE Interface Configuration Options | Paradyne 3160-A2-GB21-50

ACCULINK 316x DSU/CSU

DTE Interface Configuration Options

NOTE

These configuration options are only available for 2-port and 4-port DSU/CSUs.

Table C-1

(1 of 2)

DTE Interface Configuration Options

DTE Port: Enab

Next Enab Disab Prev

DTE Drop/Insert (DSX-1) Port. Enables the use of the DTE Drop/Insert (DSX-1) port.

Enab ± Allows the use of the DTE Drop/Insert (DSX-1) interface.

Disab ± Prohibits the use of the DTE Drop/Insert (DSX-1) interface.

NOTE: When this configuration option is disabled, you cannot display or configure any other DTE Interface configuration options. If the clock source configuration option is set to DTE, it is changed to NET.

DTE Framing: ESF (Factory 1) D4 (Factory 2)

Next D4 ESF Prev

DTE Line Framing Format. Designates the framing format for the DTE Drop/Insert (DSX-1) interface.

D4 ± Configures for the D4 framing format.

ESF ± Configures for the Extended Superframe framing format.

DTE Coding: B8ZS (Factory 1) AMI (Factory 2)

Next AMI B8ZS Prev

DTE Line Coding Format. Designates the line coding format to be used on the DTE Drop/Insert (DSX-1) interface.

AMI ± Uses the Alternate Mark Inversion coding format.

B8ZS ± Uses the Bipolar 8 Zero Suppression coding format.

Equal: 0 Ð133

Next 0 Ð133 133 Ð266 266 Ð399 399 Ð533 533 Ð 655 Prev

DTE Line Equalization. Specifies the DTE line equalization compensation parameters that permit a standard DTE Drop/Insert (DSX-1) signal to be delivered over a distance of up to 655 feet.

C-2

January 1997

3160-A2-GB21-50

Image 107

Paradyne 3160-A2-GB21-50 manual Table C-1 DTE Interface Configuration Options, DTE Port Enab Next Enab Disab Prev

Contents

Area Code Change Acculink 316X Data Service Unit Channel Service Unit Copyright 1997 Paradyne Corporation. All rights reserved Warranty, Sales, and Service InformationTrademarks Operators Guide 3160-A2-GB21-50 Important Safety Instructions 315x CSU Facility Interface Codes Description Government Requirements and Equipment ReturnUnited States Canada Important Instructions Acculink 316x DSU/CSU Table of Contents Glossary Index Reference Documents PrefaceObjectives and Reader Assumptions Related Documents Acculink 316x DSU/CSU Overview FeaturesIntroduction Front Panel Emulation Telnet AccessAlarm Message Capability DTE Drop/Insert DSX-1 Interface Standalone DSU/CSU Front Panel Physical Description 3164 DSU/CSU Rear Panel Standalone DSU/CSU Rear Panel AUX Port Application Examples Installation Network EDL is only available on 2-port and 4-port DSU/CSUs Snmp or Telnet Connection Examples Connection through a LAN Adapter Important Instructions Optional Power SourcesInstalling the +24 Vdc Power Supply 10. ±48 Vdc Single Source Power Supply Pinouts Installing the Single ±48 Vdc Power Supply 11. ±48 Vdc Redundant Source Power Supply Pinouts Installing the Redundant ±48 Vdc Power Supply 12. Cabling Examples Cabling Examples Self-Test Power-Up Self-TestSelf-Test Progress Self-Test Passed Acculink 316x DSU/CSU January LCD Operation Standalone DSU/CSU Front Panel Using the Front Panel LCD Keypad Test Jacks LEDs Network Interface LEDs System LEDsName Color Meaning PDV DTE Drop/Insert DSX-1 Interface LEDs Name Color Meaning DTR Data Port LEDs Identity Cust ID=xxxxxxxx Displaying Unit IdentityStatus TStat LED ID Identity Selecting the DTE Drop/Insert or Data Port for LED Display Setting Customer Identification LED Display Test NetSig Displaying LED ConditionsStatus Perf TStat LED Select LEDs T1 Prt1 Prt2 Changing Configuration Options Edit DTE Port NET Displaying/Editing Configuration OptionsLoad from Activ Cust1 Choose Funct Edit Save Port Select Copy Prt1 Prt2 Saving Edit ChangesSelecting/Copying to a Specific Port Save Edit to Activ Cust1 Copy To All Prt1 Prt2 Configuring the DSU/CSU for Snmp or Telnet AccessSelecting the Port Copy From Prt1 Prt2 Prt3 Edit Chan Gen User Setting the IP AddressEdit User Alarm Mgmt Mgmt Config Gen Trap 010.155.111.222 Up Down Save Selecting the Link Layer ProtocolCom IP Adr Next Edit Clear 000.000.000.000 Up Down Save Com Link Next PPP Slip Specifying the Community Names and Access Types Public Up Down Save Access Next Read R/WCommunityName1 Next Edit Clear Snmp Trap Next Enab Disab Configuring Snmp TrapsEnabling Snmp Trap Messages Selecting the Number of Trap Managers Trapn Dst Next None Com Configuring a Destination for Snmp TrapsNum Trap Mgrs1 Next Example of Channel Allocation Configuring DS0 Channels Example of Interface Worksheet Network Interface Network Channel Allocation Example of RBS Information Worksheet DTE Chan Assign Voice Config N1 ± RBS or Data Port Chan Options Value Conf Port Channel Configuration Worksheet Ports 1 10. Port Channel Configuration Worksheet Ports 3 Displaying DS0 Channel Assignments Display Channel SymbolsSymbol Meaning Chan Channel Config Prt1 Prt2 Prt3Allocating Data Ports EditDTE Port Port Rate384 Next 64 Block or Acami Assignment MethodAssign ToNET Next NET DTE Assign By Next Block Acami Next Prt1 Prt2 Individual Channel Assignment MethodAssign ByBlock Next Block Acami Assign ByChan Block Acami Chan DTE Channels Assign Voice Port1 Providing Backup CapabilityClearing DS0 Channel Allocation Clear Channel Selecting the Timing Source 11. Common Clocking Configurations Configuring for External Timing Configuring for Network Timing Control Reset CID Passwd Establishing Access Security on a PortSetting a Password PasswordNone Next None Com Passwd Up Down Done Entering a Password to Gain AccessAcquiring/Releasing User Interface Acquiring the Active User Interface Releasing the Active User Interface FP Access Next Enab DisabEnabling/Disabling the Front Panel Xxxxxxxxxxxxxxxxx Next Prev Edit Using the Integral Modem in Standalone DSU/CSUsCall Setup Pass Dial ChDir Entering Numbers in the Phone Directories Xxxxxxxxxxxxxxxxx Up Down Save Up Down Dial Initiating a Call for Front Panel Pass-Through Operation Disconnect Command Complete Disconnecting the Modem ConnectionCall Setup Disc ChDir Com Port Next Enab Disab Enabling the Communication Port for Carrier-Mounted DSU/CSUs Ascii HEX Control Sequences Download Operations Deactivating the Alarm Relay for Carrier-Mounted DSU/CSUsResetting the DSU/CSU Acculink 316x DSU/CSU January Security Lvl1 Lvl2 User Interface Access Security for Standalone DSU/CSUsChanging User Interface Access Security Acculink 316x DSU/CSU January Maintenance Self-Test Health Messages Self-Test HealthStatus DevHS STest Perf STest Health Passed Health and Status Messages Device Health and StatusDevice H/S OOF at DTE Auto Dev H/S OOF at DTE Health and Status Messages User Current Event = xx,xxx Performance ReportsPerformance Telco User Prt1 User Registers Cur 24Tot Intvl Control Rel User 24 Hour VldIntvl =User Intvl Up Down Dsply User Intvl ES=xxx VldIntvl CurTimerEvent Complete StEvnt Alarms Snmp Trap per Interface Trap Meaning Snmp TrapsEnterprise-Specific Trap Definitions Trap Value Event Yellow at DTE TroubleshootingTroubleshooting Symptom Possible Cause Solutions Yellow at Net X x x x x AIS at DTE Mon Jack Eqpt Test JacksControl Passwd Mon Test Jack Name Function Test Jack Functions Test Rlpbk Lpbk Ptrns Test CommandsRemote Loopback Tests Sending a Line Loopback Up or Down Rem Loop Type Prt1 Prt2 Prt3 Sending a V.54/ANSI FT1 Activation/Deactivation Valid Loopback Combinations Local Loopback Tests Loopback Abort LLB PLB Starting a Line LoopbackStarting a Payload Loopback Loopback Starting a DTE LoopbackStarting a Repeater Loopback Loopback Dclb Prt1 Prt2 Prt3 Starting a Data Channel LoopbackStarting a Data Terminal Loopback Loopback Abort All Aborting LoopbacksLoopback Dtlb Prt1 Prt2 Prt3 Sending Test Patterns Test Patterns Qrss Network Qrss Port Monitoring Test PatternsPatterns Mon Qrss Monitor Name NET Prt1 Prt2 Patterns Abort All Send Mon Aborting Test Patterns Aborting a Lamp Test Lamp TestStarting a Lamp Test Test Status Messages Displaying DSU/CSU Test StatusStatus STest Perf TStat DSU ESF Front Panel Menu a 3160-A2-GB21-50 Models 3160/3164 Technical Specifications B Port Interface DTE Interface Configuration Options Configuration Options C DTE Framing ESF Factory 1 D4 Factory Next D4 ESF Prev DTE Interface Configuration OptionsTable C-1 DTE Interface Configuration Options DTE Port Enab Next Enab Disab Prev Send Ones Enab Next Enab Disab Prev Extrn DLB Disab Next Enab Disab Prev Port Type E530 Factory Next E530 V.35 RS449 Prev Port Configuration OptionsPort Configuration Options Table C-2 Tx Clock Int Next Int Ext Prev Table C-2 Port Configuration OptionsAll Ones Both Next Disab DTR RTS Both Prev Rcv Yellow Halt Next None Halt Prev EDL Disab Next Enab Disab Prev InvertTxC Disab Next Enab Disab PrevInvrtData Disab Next Enab Disab Prev Near-end Disab Next Disab Maint Send Both Prev Err Rate 10E-4 Next 10E-4 10E-5 10E-6 10E-7 10E-8 10E-9 Prev Mgmt Link Disab Next Enab Disab Prev Far-end Disab Next Disab Maint Prev Table C-3 Network Interface Configuration Options Network Interface Configuration Options Circuit Ident Next Edit Clear Prev NET LLB Enab Next Enab Disab PrevNET PLB Enab Next Enab Disab Prev Bit Stuff Next 62411 Part68 Disab Prev Table C-4 DTE Channel Configuration Options Channel Configuration Options Assign By Block Next Block Acami Chan Prev Table C-5 Data Port Channel Configuration OptionsChannel Config Dsply Clear DTE Prt1 Prt2 Prt3 Prt4 Assign To NET Next NET DTE Prtn Prtn Prtn Prev 1472 1536 Prev Next 112 168 224 280 336 392 Port Rate Next 128 192 256 320 384 448576 640 704 768 832 896 960 1088 1216 1280 1344 N10 N11 N12 N24 Next Prev D10 D11 D12 D24 Clock Src NET Next NET DTE Prt1 Int Ext Prev General Configuration OptionsTable C-6 General Configuration Options Gen Yellow Enab Next Enab Disab Prev Tst Duration Next Up Down Save Prev Tst Timeout Enab Next Enab Disab Prev Table C-7 User Interface Configuration Options User Interface Configuration Options ComExtDev Disab Next Disab AT Other Prev Password None Next None Com Modem Both PrevCom Port Disab Next Enab Disab Prev Com Use Ascii Next Mgmt Ascii Daisy Term Prev ComEscapeSeq Next Edit Clear Prev ComConnPrefix Next Edit Clear PrevComConnected Next Edit Clear Prev Com Clk Int Next Int Ext Prev ComEscDel None Next None 0.2s 0.4s 0.6s 0.8s 1.0s PrevComDisconnect Next Edit Clear Prev Com Type Async Next Async Sync Prev CStop Bits Next 1 1.5 2 Prev Com Rate Next 1.2 2.4 4.8 9.6 14.4 19.2 38.4 PrevChar Length Next 7 8 Prev CParity None Next None Even Odd Prev Modem Rate Next 1.2 2.4 Prev CmDiscTm Next Up Down Save PrevModem Use Ascii Next Mgmt Ascii Term Prev Modem Type Async Next Async Sync Prev MDiscTm Next Up Down Save Prev MStop Bits Next 1 2 PrevLSpaceDsc Disab Next Enab Disab Prev MInActTm Disab Next Enab Disab Prev TnInActTm Disab Next Enab Disab Prev Aux Rate Next 9.6 14.4 19.2 38.4 PrevTnSession Disab Next Enab Disab Prev TnPaswd Disab Next Enab Disab Prev Snmp Trap Disab Next Enab Disab Prev Alarm Configuration OptionsTable C-8 Alarm Configuration Options Alrm Msg Disab Next Disab Modem Com Both Prev Next None 1 2 3 4 5 Prev Dial Delay Next 1 2 3 4 5 6 7 8 9 10 PrevDialOut Disab Next Enab Disab Prev Call Retry Disab Next Enab Disab Prev AlrmRelay Disab Next Enab Disab Prev Table C-9 General Management Configuration Options Management Configuration Options System Contact Next Edit Clear Prev NMS n Access Read Next Read R/W PrevSystem Name Next Edit Clear Prev System Location Next Edit Clear Prev IP Adr Next Edit Clear Prev Access 1 Read Next Read R/W PrevAccess 2 Read Next Read R/W Prev CommunityName2 Next Edit Clear Prev Modem IP Adr Next Edit Clear Prev Com IP Adr Next Edit Clear PrevCom NetMask Next Edit Clear Prev Com Link PPP Next PPP Slip Prev Modem Link PPP Next PPP Slip Prev Mdm NetMask Next Edit Clear PrevAlt Mdm IP Adr Next Edit Clear Prev Alt Mdm NetMask Next Edit Clear Prev IPBusMast Disab Next Enab Disab Prev Aux IP Adr Next Edit Clear PrevAux NetMask Next Edit Clear Prev Table C-9 General Management Configuration Options Gen Trap Both Next Disab Warm Auth Both Prev Table C-10 Management Trap Configuration OptionsNum Trap Mgrs Next 1 2 3 4 5 6 Prev Trapn IP Adr Next Edit Clear Prev Trap I/F All Next NET DTE T1s Ports All Prev Entp Trap Enab Next Enab Disab PrevLink Trap Both Next Disab Up Down Both Prev General Configuration WorksheetsValue Default in Bold DTE Options User Options Alarm Prt4 Options Prt1 OptionsPrt2 Options Prt3 Options Network Interface Network Channel Allocation D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 Port Chan Options Port Chan Options Mgmt Trap General Mgmt T1 Network Interface Table D-1 T1 Network Interface Connector Signal Pin NumberPin Assignments D Figure D-1. T1 Line Interface Cable, RJ48C-to-RJ48C DTE Drop/Insert Interface Table D-2 DTE Drop/Insert DSX-1 Connector Signal Pin Number Modem Port Interface Table D-3 Integral Modem Port Connector Signal Pin Number AUX Port Interface Table D-4 AUX Port Connector Signal Direction Pin Number COM Port Interface Table D-5 COM Port Connector Signal Direction Pin Number Figure D-5. COM Port-to-PC Cable Direction Pin Mnemonic Number EIA 530A Port Interface ConnectorTable D-6 EIA 530A Port Interface Connector Signal Circuit Figure D-7. EIA 530A-to-RS449 Cable EIA 530A-to-RS449 Cable Interface Table D-7 RS449 Cable Interface Signal Circuit Figure D-8. EIA 530A-to-V.35 Cable EIA 530A-to-V.35 Cable Interface Direction Pin Number Table D-8 Cable Interface Signal Figure D-9. EIA 530A-to-X.21 Cable EIA 530A-to-X.21 Cable Interface Table D-9 Cable Interface Signal Pin Serial Crossover Cable Table D-11 External Clock Connector Signal Pin Number Power Input ConnectorOptional DC Power Cable Table D-10 DC Power Connector Signal Pin Number Snmp MIB Objects E System Group, MIB MIB II RFC Interface Group, MIB System Group ± ªsysServicesº Object system Interface Group ± ªifDescrº Object ifEntry Interface Group ± ªifOperStatusº Object ifEntry IP Group, MIB IP Group ± ªipAdEntAddrº Object ipAddrEntry IP Group ± ªipRouteDestº Object ipRouteEntry DS1/E1 MIB RFC Near End Group ± ªdsx1ValidIntervalsº Object dsx1ConfigEntry Near End Group ± ªdsx1LineStatusº Object dsx1ConfigEntry DS1 Fractional Group, DS1/E1 MIB Far End Group, DS1/E1 MIB General Port Table, RS-232-like MIB RS-232-like MIB RFC Asynchronous Port Table, RS-232-like MIB General Port Table ± ªrs232PortTypeº Object rs232PortEntry Synchronous Port Table, RS-232-like MIB Output Signal Table, RS-232-like MIBInput Signal Table, RS-232-like MIB Generic Interface Test Table, Generic Interface MIB Generic-Interface MIB Extensions RFC Enterprise MIB Correlation between Menu Commands and Snmp Objects Dsx1CurrentSES Dsx1TimeElapsedDsx1CurrentES Dsx1CurrentUAS Set dsx1LoopbackConfig for DTE T1 to dsx1LineLoop Set dsx1LoopbackConfig for Net T1 to dsx1LineLoopSet dsx1LoopbackConfig for Net T1 to dsx1NoLoop Set dsx1LoopbackConfig for Net T1 to dsx1PayloadLoop Set/Display rs232PortInSpeed or rs232PortOutSpeed for COM Set/Display dsx1FracNumber and dsx1FracIfindex for DTE T1Set/Display dsx1FracNumber and dsx1Fracifindex for DTE or Display rs232PortInSpeed or rs232PortOutSpeed for port n Acculink 316x DSU/CSU IP Network Addressing Scenarios F Figure F-1. Daisy-Chained Standalone at the Central Site Scenario 135.18.2.17 135 135 Figure F-5. Multiple COM Ports Connected to Different NMSs Front Panel Emulation G Installing Front Panel Emulation Software Starting Front Panel Emulation Async Terminal Operation H Before Using the Async Terminal Ending an Async Terminal Session Initiating an Async Terminal Session Menu Organization Main Status Test Configuration Control Table H-2 Keyboard Keys Usage Using Async Terminal ScreensTable H-1 Screen Function Keys Usage Figure H-3. Customer Identification Screen Figure H-4. Example of Display LEDs Screen Figure H-5. Configuration Load Screen Displaying or Editing Configuration Options Figure H-6. Configuration Edit/Display Screen Figure H-7. Configuration Save Screen Figure H-8. Enabling a Password Figure H-9. Setting a Password Figure H-10. Entering a Password DTE Interface Options Front Panel Configuration Worksheets for the Async Terminal InterfaceNetwork Interface Options Front Panel Equivalent Front Panel Sync Data Port Options Port Front PanelSync Data Port Options Port Async Terminal Operation Front Panel Options Equivalent Value Default in BoldGeneral Options Front Panel User Interface Internal Modem Options Equivalent External Device Options EquivalentTelnet Sessions Options Equivalent Port Use Aux Use None, Mgmt, Daisy Alarm & Trap Options Front PanelAuxiliary Port Options Equivalent General Snmp Management Options Equivalent Management and Communication Front PanelCommunication Protocol Options Equivalent Snmp Traps Options Equivalent Snmp NMS Security Options Equivalent Cable numbers for DSU/CSU are located Equipment Feature NumberEquipment List Acculink 316x DSU/CSU Acami allocation method Glossary AWG CRC6 DSR ISO LCP PDU RTS TXC Acculink 316x DSU/CSU Glossary-10 Index Index-2 Index Index-4 Index-5 Index-6