Paradyne 3160-A2-GB21-50 (3 of 5)

ACCULINK 316x DSU/CSU

C-6 January 1997 3160-A2-GB21-50

Table C-2

(3 of 5)

Port Configuration Options

InvertTxC: Disab

Next Enab Disab Prev

Invert Transmit Clock. Specifies whether the clock supplied by the DSU/CSU on the TXC interchange circuit DB

(CCITT 114) is phase inverted with respect to the Transmitted Data interchange circuit BA (CCITT 103). This

configuration option is useful when long cable lengths between the DSU/CSU and the DTE are causing data errors.

Enab – Indicates TXC supplied by the DSU/CSU on this port is phase inverted.

Disab – Indicates TXC supplied by the DSU/CSU on this port is not phase inverted.

InvrtData: Disab

Next Enab Disab Prev

Invert Transmitted and Received Data. Specifies whether the port’s transmitted data and received data are logically

inverted before being transmitted or received. This configuration option is useful for applications where HDLC data is

being transported. Inverting the data ensures that the density requirements for the network interface are met.

Enab – Indicates the transmitted data and received data for this port are inverted.

Disab – Indicates the transmitted data and received data for this port are not inverted.

EDL: Disab

Next Enab Disab Prev

Embedded Data Link. Specifies whether Embedded Data Link (EDL) is enabled for a particular port. If EDL is enabled,

then 8 kbps of the total bandwidth allocated for this port is not available to the synchronous data port. For example, if the

port rate is 256 kbps (4 DS0 channels allocated) and EDL is enabled, then only 248 kbps is available to the port. EDL

provides the following: detection of frame synchronization, CRC of the data stream (excluding the 8 kbps EDL), and an

in-band data link (4 kbps) between the local and remote units. The 4 kbps in-band data link can be used for performance

report messages and as an IP link for SNMP or Telnet sessions.

Enab – Indicates the port’s EDL is enabled.

Disab – Indicates the port’s EDL is disabled.

NOTE: This configuration option is only available on 2-port and 4-port DSU/CSUs.

NOTE: If the local DSU/CSU’s EDL is enabled, then the remote DSU/CSU’s EDL must also be enabled.

NOTE: EDL is not recommended for networks in which data is examined for routing purposes (e.g., frame relay, x.25).

Contents

Main Page ACCULINK 316x Data Service Unit/Channel Service Unit Warranty, Sales, and Service Information Trademarks Important Safety Instructions Notices Government Requirements and Equipment Return United States Canada Page Page Table of Contents Preface 1. Introduction 2. Installation 3. Operation 4. Maintenance Appendices Glossary Index Preface Objectives and Reader Assumptions Related Documents Reference Documents Page Introduction Features DTE Drop/Insert (DSX-1) Interface Alarm Message Capability Front Panel Emulation Integral Modem Async Terminal Interface Support Physical Description Standalone DSU/CSU Front Panel ACCULINK 316x DSU/CSU 1-4 January 1997 3160-A2-GB21-50 F1 F2 F3 Figure 1-2. 3164 DSU/CSU Front Panel F1 F2 F3 Figure 1-3. 3165 DSU/CSU Front Panel LCD ACCULINK Standalone DSU/CSU Rear Panel Figure 1-6. 3165 DSU/CSU Rear Panel Table 1-1 Standalone DSU/CSU Rear Panel Connectors Name Function Installation ACCULINK 3151 CSU and 3161 DSU/CSU General Information Guide COMSPHERE 3000 Series Carrier Installation Manual Application Examples NETWORK Figure 2-1. Point-to-Point Application Example NETWORK SERVICES Figure 2-3. Fractional T1 Application Example Figure 2-2. Shared Access Application Example FRACTIONAL NETWORK SNMP or Telnet Connection Examples NETWORK NETWORK Figure 2-6. Connection through a LAN Adapter Figure 2-8. Remote Access through FDL/EDL NETWORK Figure 2-7. LAN Adapter and Daisy Chaining NETWORK Important Instructions Optional Power Sources Installing the +24 Vdc Power Supply Installing the Single 48 Vdc Power Supply Installing the Redundant 48 Vdc Power Supply X ACCULINK 316x DSU/CSU 2-8 January 1997 3160-A2-GB21-50 Cabling Examples The DSU/CSU is supplied with an ac power module and a VF cable for the integral modem. Figure 2-12. Cabling Examples T1 NETWORK PSTN Power-Up Self-Test Page Operation ACCULINK 3151 CSU and 3161 DSU/CSU General Information Guide COMSPHERE 3000 Series Carrier Installation Manual Using the Front Panel Front Panel Emulation LCD Keypad Test Jacks LEDs Table 3-1 System LEDs Table 3-2 Network Interface LEDs Page Table 3-4 Data Port LEDs Displaying Unit Identity xxxxxxx xxxx xxxx-xxx Setting Customer Identification Selecting the DTE Drop/Insert or Data Port for LED Display Displaying LED Conditions Changing Configuration Displaying/Editing Configuration Options Saving Edit Changes Selecting/Copying to a Specific Port Configuring the DSU/CSU for SNMP or Telnet Access Selecting the Port Setting the IP Address Selecting the Link Layer Protocol Specifying the Community Name(s) and Access Type(s) Page Configuring SNMP Traps Enabling SNMP Trap Messages Selecting the Number of Trap Managers Configuring a Destination for SNMP Traps Configuring DS0 Channels Network Interface Network Channel Allocation DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation Figure 3-7. Example of Interface Worksheet DTE Chan Config Assign: (N1 24) Voice Figure 3-8. Example of RBS Information Worksheet (RBS or Data) Conf Options Value Figure 3-9. Port Channel Configuration Worksheet (Ports 1 and 2) Conf Options Value Figure 3-10. Port Channel Configuration Worksheet (Ports 3 and 4) Displaying DS0 Channel Assignments Allocating Data Ports Block or ACAMI Assignment Method Individual Channel Assignment Method Allocating DS0 Channels from the DTE Drop/Insert Interface to the Network Interface Page Clearing DS0 Channel Allocation Providing Backup Capability Selecting the Timing Source Configuring for Network Timing Configuring for External Timing Establishing Access Security on a Port Setting a Password Entering a Password to Gain Access Acquiring/Releasing the User Interface Acquiring the Active User Interface User I/F Releasing the Active User Interface Enabling/Disabling the Front Panel Using the Integral Modem in Standalone DSU/CSUs Entering Numbers in the Phone Directories Page Initiating a Call for Front Panel Pass-Through Operation Configuration Options), Initiating a Call for PC, ASCII Terminal/Printer, or SNMP Operation Disconnecting the Modem Connection Enabling the Communication Port for Carrier-Mounted Table 3-7 Control Sequences Sequence ASCII HEX Deactivating the Alarm Relay for Carrier-Mounted Resetting the DSU/CSU Download Operations Page User Interface Access Security for Standalone Changing User Interface Access Security Page Maintenance Self-Test Health Device Health and Status Table 4-2 Health and Status Messages Message Description Performance Reports xx,xxx Page Table 4-3 Performance Registers Register Interval Description Totals Description Table 4-3 Performance Registers Register Totals DescriptionInterval Description Alarms SNMP Traps Troubleshooting For problems other than those listed in the table, please contact your service representative. Table 4-6 Troubleshooting Symptom Possible Cause Solutions Table 4-6 Troubleshooting Symptom SolutionsPossible Cause Test Jacks Table 4-7 Test Jack Functions Test Jack Name Function Test Commands Remote Loopback Tests Sending a Line Loopback Up or Down Sending a V.54/ANSI FT1 Activation/Deactivation Type Local Loopback Tests Starting a Line Loopback Starting a Payload Loopback Starting a DTE Loopback Starting a Repeater Loopback Starting a Data Channel Loopback Starting a Data Terminal Loopback Aborting Loopbacks Test Name Test Patterns Sending Test Patterns Name Name and Dest Monitoring Test Patterns Name Aborting Test Patterns Send or Mon Lamp Test Starting a Lamp Test Aborting a Lamp Test Displaying DSU/CSU Test Status A Front Panel Menu Page B Technical Specifications Table B-1 Models 3160/3164/3165 DSU/CSUs Technical Specifications Specifications Criteria C Configuration Options DTE Interface Configuration Options Page Port Configuration Options (1 of 5) (2 of 5) (3 of 5) (4 of 5) (5 of 5) Network Interface Configuration Options Table C-3 Network Interface Configuration Options Table C-3 Network Interface Configuration Options Channel Configuration (1 of 3) Configuring DS0 Channels Operation OR Page General Configuration Options Table C-6 General Configuration Options Table C-6 General Configuration Options User Interface Configuration Options (2 of 8) (3 of 8) (4 of 8) X.X (5 of 8) (6 of 8) (7 of 8) (8 of 8) Alarm Configuration Options Table C-8 Alarm Configuration Options Table C-8 Alarm Configuration Options Management Configuration (2 of 7) (3 of 7) (4 of 7) (5 of 7) (6 of 7) (7 of 7) Table C-10 Management Trap Configuration Options Table C-10 Management Trap Configuration Options Alarm Configuration Options Configuration Worksheets Page Prt1 Options Value (Default in Bold) Prt2 Options Value (Default in Bold) Prt3 Options Value (Default in Bold) Prt4 Options Value (Default in Bold) Network Interface Network Channel Allocation DTE Drop/Insert (DSX-1) Interface DTE (DSX-1) Channel Allocation DTE Chan Config Assign: (N1 24) Voice (RBS or Data) Page Conf Options Value (Default in Bold) Page D Pin Assignments T1 Network Interface Page DTE Drop/Insert Interface MODEM Port Interface AUX Port Interface COM Port Interface Page EIA 530A Port Interface Connector EIA 530A-to-RS449 Cable Interface The EIA 530A-to-RS449 adapter cable (Figure D-7) provides the RS449 interface shown in Table D-7. Figure D-7. EIA 530A-to-RS449 Cable Table D-7 RS449 Cable Interface Signal Circuit Mnemonic CCITT Number Direction Pin EIA 530A-to-V.35 Cable Interface The EIA 530A-to-V.35 adapter cable (Figure D-8) provides the V.35 interface shown in Table D-8. Figure D-8. EIA 530A-to-V.35 Cable Table D-8 V.35 Cable Interface Signal CCITT Number Direction Pin EIA 530A-to-X.21 Cable Interface The EIA 530A-to-X.21 adapter cable (Figure D-9) provides the X.21 interface shown in Table D-9. Figure D-9. EIA 530A-to-X.21 Cable Page Serial Crossover Cable Figure D-10. Serial Crossover Cable Power Input Connector Optional DC Power Cable External Clock Interface E SNMP MIB Objects MIB II (RFC 1213) System Group, MIB II System Group sysDescr Object (system 1) System Group sysObjectID Object (system 2) System group sysContact Object (system 4) System Group sysServices Object (system 7) Interface Group, MIB II Interface Group ifNumber Object (interfaces 1) Interface Group ifIndex Object (ifEntry 1) Interface Group ifDescr Object (ifEntry 2) Interface Group ifType Object (ifEntry 3) Interface Group ifMtu Object (ifEntry 4) Interface Group ifSpeed Object (ifEntry 5) Interface Group ifAdminStatus Object (ifEntry 7) Interface Group ifOperStatus Object (ifEntry 8) Interface Group ifLastChange Object (ifEntry 9) Interface Group Input Counters (objects ifEntry 10 to ifEntry 15) Interface Group Output Counters (objects ifEntry 16 to ifEntry 21) IP Group, MIB II IP Group ipForwarding Object (ip 1) IP Group ipAddrTable Object (ip 20) IP Group ipAdEntAddr Object (ipAddrEntry 1) IP Group ipRouteDest Object (ipRouteEntry 1) IP Group ipRouteIfIndex Object (ipRouteEntry 1) IP Group ipRouteMetric2 Object (ipRouteEntry 4) IP Group ipRouteProto Object (ipRouteEntry 9) IP Group ipRouteAge Object (ipRouteEntry 10) DS1/E1 MIB (RFC 1406) Near End Group, DS1/E1 MIB Near End Group dsx1TimeElapsed Object (dsx1ConfigEntry 3) Near End Group dsx1ValidIntervals Object (dsx1ConfigEntry 4) Near End Group dsx1LineType Object (dsx1ConfigEntry 5) Near End Group dsx1LineCoding Object (dsx1ConfigEntry 6) Near End Group dsx1SendCode Object (dsx1ConfigEntry 7) Near End Group dsx1LineStatus Object (dsx1ConfigEntry 10) Near End Group dsx1SignalMode Object (dsx1ConfigEntry 11) Near End Group dsx1TransmitClockSource Object (dsx1ConfigEntry 12) Near End Group dsx1Fdl Object (dsx1ConfigEntry 13) Near End Group The DS1 Current Table Objects (dsx1CurrentEntry) Near End Group The DS1 Interval Table Objects (dsx1IntervalEntry) Near End Group The DS1 Total Table Objects (dsx1TotalEntry) Far End Group, DS1/E1 MIB DS1 Fractional Group, DS1/E1 MIB RS-232-like MIB (RFC 1317) Number of Ports rs232Number Object (rs232 1) General Port Table, RS-232-like MIB General Port Table rs232PortIndex Object (rs232PortEntry 1) Page Page Output Signal Table rs232OutSigChanges (rs232OutSigEntry 4) Generic-Interface MIB Extensions (RFC 1229) Generic Interface Test Table, Generic Interface MIB Generic Interface Test Table ifExtnsTestType Object (ifExtnsTestEntry 4) Generic Interface Test Table ifExtnsTestResult Object (ifExtnsTestEntry 5) Generic Interface Test Table ifExtnsTestCode Object (ifExtnsTestEntry 6) Enterprise MIB Correlation between Menu Commands and SNMP Objects (1 of 3) Page Page Page F IP Network Addressing Scenarios Scenario 1 Scenario 2 Scenario 3 Scenario 4 Figure F-4. Local Carrier Connected to Remote Carriers an Alternative 135.19.6.1 . . . . 135.19.6.16 135.19.20.1 . . . . 135.19.20.16 135.19.1.1 . . . . 135.19.1.16 Scenario 5 G Front Panel Emulation Installing Front Panel Emulation Software Starting Front Panel Emulation Displaying LED Conditions Operation H Async Terminal Operation Before Using the Async Terminal Initiating an Async Terminal Session Ending an Async Terminal Session Menu Organization Figure H-2. Menu Organization Using Async Terminal Screens Setting Customer Identification Displaying LED Conditions Changing Configuration Displaying or Editing Configuration Options Page Saving Edit Changes Establishing Access Security on a Port Setting a Password Entering a Password to Gain Access Configuration Worksheets for the Async Terminal Interface Sync Data Port Options (Port 1) Front Panel Sync Data Port Options (Port 2) Front Panel Sync Data Port Options (Port 3) Front Panel Sync Data Port Options (Port 4) Front Panel Page Page Page Communication Protocol Options Front Panel General SNMP Management Options Front Panel SNMP NMS Security Options Front Panel SNMP Traps Options Front Panel I Equipment List Page Glossary Page Page Page Page Page Page Page Page Page Index A B C D E F G I K L M N O P Q R S T U V W X X.21 interface, D-14 Y