Configuring a Destination for Snmp Traps | Paradyne 3160-A2-GB21-50

ACCULINK 316x DSU/CSU

6. From the Mgmt Config screen, select Trap.

Mgmt Config:

Gen Trap

F1 F2 F3

7.Select the number of SNMP managers to receive traps (from 1 through 6) by using the appropriate Function key. Use the scroll keys, if necessary.

Num Trap Mgrs:1
Next 1	2
F1	F2	F3

Configuring a Destination for SNMP Traps

A destination must be configured for each SNMP trap manager specified. This configuration option is displayed for the number of trap managers specified by the Number of Trap Managers configuration option.

To configure an IP address for the SNMP trap manager,

1.From the top-level menu screen, select Cnfig.

2.Select the configuration option set to be copied into the Edit area by using the appropriate Function key. Use the scroll keys, if necessary.

3.Select Edit.

4.From the Edit screen, press the key until the Mgmt selection appears on the screen.

5. Select Mgmt.

Edit:
User	Alarm	Mgmt
F1	F2	F3

6. From the Mgmt Config screen, select Trap.

Mgmt Config:

Gen Trap

F1 F2 F3

7.Press F1 (Next) until the Trapn IP Address configuration option appears.

8.Press F2 (Edit) to edit the IP address. You have the option of using F3 (Clear) to reset the IP address to the factory default 000.000.000.000. Refer to the Setting the IP Address section on page 3-15 for more information on setting an IP address.

9.Press F1 (Next) until the Trapn Destination configuration appears, and select the destination for the SNMP trap by using the appropriate Function key. Use the scroll keys, if necessary.

Trapn Dst:

Next None Com

F1 F2 F3

3-20

January 1997

3160-A2-GB21-50

Image 49

Paradyne 3160-A2-GB21-50 manual Configuring a Destination for Snmp Traps, Num Trap Mgrs1 Next, Trapn Dst Next None Com

Contents

Area Code Change Acculink 316X Data Service Unit Channel Service Unit Trademarks Warranty, Sales, and Service InformationOperators Guide 3160-A2-GB21-50 Copyright 1997 Paradyne Corporation. All rights reserved Important Safety Instructions United States Government Requirements and Equipment Return315x CSU Facility Interface Codes Description Canada Important Instructions Acculink 316x DSU/CSU Table of Contents Glossary Index Objectives and Reader Assumptions PrefaceRelated Documents Reference Documents Acculink 316x DSU/CSU Introduction FeaturesOverview Alarm Message Capability Telnet AccessDTE Drop/Insert DSX-1 Interface Front Panel Emulation Standalone DSU/CSU Front Panel Physical Description 3164 DSU/CSU Rear Panel Standalone DSU/CSU Rear Panel AUX Port Application Examples Installation Network EDL is only available on 2-port and 4-port DSU/CSUs Snmp or Telnet Connection Examples Connection through a LAN Adapter Installing the +24 Vdc Power Supply Optional Power SourcesImportant Instructions 10. ±48 Vdc Single Source Power Supply Pinouts Installing the Single ±48 Vdc Power Supply 11. ±48 Vdc Redundant Source Power Supply Pinouts Installing the Redundant ±48 Vdc Power Supply 12. Cabling Examples Cabling Examples Self-Test Progress Power-Up Self-TestSelf-Test Passed Self-Test Acculink 316x DSU/CSU January LCD Operation Standalone DSU/CSU Front Panel Using the Front Panel LCD Keypad Test Jacks LEDs Name Color Meaning System LEDsNetwork Interface LEDs PDV DTE Drop/Insert DSX-1 Interface LEDs Name Color Meaning DTR Data Port LEDs Status TStat LED ID Displaying Unit IdentityIdentity Identity Cust ID=xxxxxxxx Selecting the DTE Drop/Insert or Data Port for LED Display Setting Customer Identification Status Perf TStat LED Displaying LED ConditionsSelect LEDs T1 Prt1 Prt2 LED Display Test NetSig Changing Configuration Options Load from Activ Cust1 Displaying/Editing Configuration OptionsChoose Funct Edit Save Edit DTE Port NET Selecting/Copying to a Specific Port Saving Edit ChangesSave Edit to Activ Cust1 Port Select Copy Prt1 Prt2 Selecting the Port Configuring the DSU/CSU for Snmp or Telnet AccessCopy From Prt1 Prt2 Prt3 Copy To All Prt1 Prt2 Edit User Alarm Mgmt Setting the IP AddressMgmt Config Gen Trap Edit Chan Gen User Com IP Adr Next Edit Clear Selecting the Link Layer Protocol000.000.000.000 Up Down Save 010.155.111.222 Up Down Save Com Link Next PPP Slip Specifying the Community Names and Access Types CommunityName1 Next Edit Clear Access Next Read R/WPublic Up Down Save Enabling Snmp Trap Messages Configuring Snmp TrapsSelecting the Number of Trap Managers Snmp Trap Next Enab Disab Num Trap Mgrs1 Next Configuring a Destination for Snmp TrapsTrapn Dst Next None Com Example of Channel Allocation Configuring DS0 Channels Example of Interface Worksheet Network Interface Network Channel Allocation Example of RBS Information Worksheet DTE Chan Assign Voice Config N1 ± RBS or Data Port Chan Options Value Conf Port Channel Configuration Worksheet Ports 1 10. Port Channel Configuration Worksheet Ports 3 Symbol Meaning Display Channel SymbolsDisplaying DS0 Channel Assignments Allocating Data Ports Channel Config Prt1 Prt2 Prt3EditDTE Port Chan Assign ToNET Next NET DTE Block or Acami Assignment MethodAssign By Next Block Acami Port Rate384 Next 64 Assign ByBlock Next Block Acami Individual Channel Assignment MethodAssign ByChan Block Acami Chan Next Prt1 Prt2 DTE Channels Assign Voice Clearing DS0 Channel Allocation Providing Backup CapabilityClear Channel Port1 Selecting the Timing Source 11. Common Clocking Configurations Configuring for External Timing Configuring for Network Timing Setting a Password Establishing Access Security on a PortPasswordNone Next None Com Control Reset CID Passwd Acquiring/Releasing User Interface Entering a Password to Gain AccessAcquiring the Active User Interface Passwd Up Down Done Enabling/Disabling the Front Panel FP Access Next Enab DisabReleasing the Active User Interface Call Setup Pass Dial ChDir Using the Integral Modem in Standalone DSU/CSUsEntering Numbers in the Phone Directories Xxxxxxxxxxxxxxxxx Next Prev Edit Xxxxxxxxxxxxxxxxx Up Down Save Up Down Dial Initiating a Call for Front Panel Pass-Through Operation Call Setup Disc ChDir Disconnecting the Modem ConnectionDisconnect Command Complete Com Port Next Enab Disab Enabling the Communication Port for Carrier-Mounted DSU/CSUs Ascii HEX Control Sequences Resetting the DSU/CSU Deactivating the Alarm Relay for Carrier-Mounted DSU/CSUsDownload Operations Acculink 316x DSU/CSU January Changing User Interface Access Security User Interface Access Security for Standalone DSU/CSUsSecurity Lvl1 Lvl2 Acculink 316x DSU/CSU January Maintenance Status DevHS STest Perf Self-Test HealthSTest Health Passed Self-Test Health Messages Device H/S OOF at DTE Device Health and StatusAuto Dev H/S OOF at DTE Health and Status Messages Health and Status Messages Performance Telco User Prt1 Performance ReportsUser Registers Cur 24Tot Intvl User Current Event = xx,xxx User Intvl Up Down Dsply User 24 Hour VldIntvl =User Intvl ES=xxx Control Rel Event CurTimerVldIntvl Complete StEvnt Alarms Enterprise-Specific Trap Definitions Trap Value Event Snmp TrapsSnmp Trap per Interface Trap Meaning Troubleshooting Symptom Possible Cause Solutions TroubleshootingYellow at Net Yellow at DTE X x x x x AIS at DTE Control Passwd Mon Test JacksMon Jack Eqpt Test Jack Name Function Test Jack Functions Remote Loopback Tests Test CommandsSending a Line Loopback Up or Down Test Rlpbk Lpbk Ptrns Rem Loop Type Prt1 Prt2 Prt3 Sending a V.54/ANSI FT1 Activation/Deactivation Valid Loopback Combinations Local Loopback Tests Starting a Payload Loopback Starting a Line LoopbackLoopback Abort LLB PLB Starting a Repeater Loopback Starting a DTE LoopbackLoopback Starting a Data Terminal Loopback Starting a Data Channel LoopbackLoopback Dclb Prt1 Prt2 Prt3 Loopback Dtlb Prt1 Prt2 Prt3 Aborting LoopbacksLoopback Abort All Sending Test Patterns Test Patterns Patterns Mon Qrss Monitoring Test PatternsMonitor Name NET Prt1 Prt2 Qrss Network Qrss Port Patterns Abort All Send Mon Aborting Test Patterns Starting a Lamp Test Lamp TestAborting a Lamp Test Status STest Perf TStat Displaying DSU/CSU Test StatusTest Status Messages DSU ESF Front Panel Menu a 3160-A2-GB21-50 Models 3160/3164 Technical Specifications B Port Interface DTE Interface Configuration Options Configuration Options C Table C-1 DTE Interface Configuration Options DTE Interface Configuration OptionsDTE Port Enab Next Enab Disab Prev DTE Framing ESF Factory 1 D4 Factory Next D4 ESF Prev Send Ones Enab Next Enab Disab Prev Extrn DLB Disab Next Enab Disab Prev Port Configuration Options Port Configuration OptionsTable C-2 Port Type E530 Factory Next E530 V.35 RS449 Prev All Ones Both Next Disab DTR RTS Both Prev Table C-2 Port Configuration OptionsRcv Yellow Halt Next None Halt Prev Tx Clock Int Next Int Ext Prev InvrtData Disab Next Enab Disab Prev InvertTxC Disab Next Enab Disab PrevEDL Disab Next Enab Disab Prev Near-end Disab Next Disab Maint Send Both Prev Err Rate 10E-4 Next 10E-4 10E-5 10E-6 10E-7 10E-8 10E-9 Prev Mgmt Link Disab Next Enab Disab Prev Far-end Disab Next Disab Maint Prev Table C-3 Network Interface Configuration Options Network Interface Configuration Options NET PLB Enab Next Enab Disab Prev NET LLB Enab Next Enab Disab PrevBit Stuff Next 62411 Part68 Disab Prev Circuit Ident Next Edit Clear Prev Table C-4 DTE Channel Configuration Options Channel Configuration Options Channel Config Dsply Clear DTE Prt1 Prt2 Prt3 Prt4 Table C-5 Data Port Channel Configuration OptionsAssign To NET Next NET DTE Prtn Prtn Prtn Prev Assign By Block Next Block Acami Chan Prev 576 640 704 768 832 896 960 1088 Port Rate Next 128 192 256 320 384 4481216 1280 1344 1472 1536 Prev Next 112 168 224 280 336 392 N10 N11 N12 N24 Next Prev D10 D11 D12 D24 Table C-6 General Configuration Options General Configuration OptionsGen Yellow Enab Next Enab Disab Prev Clock Src NET Next NET DTE Prt1 Int Ext Prev Tst Duration Next Up Down Save Prev Tst Timeout Enab Next Enab Disab Prev Table C-7 User Interface Configuration Options User Interface Configuration Options Com Port Disab Next Enab Disab Prev Password None Next None Com Modem Both PrevCom Use Ascii Next Mgmt Ascii Daisy Term Prev ComExtDev Disab Next Disab AT Other Prev ComConnected Next Edit Clear Prev ComConnPrefix Next Edit Clear PrevComEscapeSeq Next Edit Clear Prev ComDisconnect Next Edit Clear Prev ComEscDel None Next None 0.2s 0.4s 0.6s 0.8s 1.0s PrevCom Type Async Next Async Sync Prev Com Clk Int Next Int Ext Prev Char Length Next 7 8 Prev Com Rate Next 1.2 2.4 4.8 9.6 14.4 19.2 38.4 PrevCParity None Next None Even Odd Prev CStop Bits Next 1 1.5 2 Prev Modem Use Ascii Next Mgmt Ascii Term Prev CmDiscTm Next Up Down Save PrevModem Type Async Next Async Sync Prev Modem Rate Next 1.2 2.4 Prev LSpaceDsc Disab Next Enab Disab Prev MStop Bits Next 1 2 PrevMInActTm Disab Next Enab Disab Prev MDiscTm Next Up Down Save Prev TnSession Disab Next Enab Disab Prev Aux Rate Next 9.6 14.4 19.2 38.4 PrevTnPaswd Disab Next Enab Disab Prev TnInActTm Disab Next Enab Disab Prev Table C-8 Alarm Configuration Options Alarm Configuration OptionsAlrm Msg Disab Next Disab Modem Com Both Prev Snmp Trap Disab Next Enab Disab Prev DialOut Disab Next Enab Disab Prev Dial Delay Next 1 2 3 4 5 6 7 8 9 10 PrevCall Retry Disab Next Enab Disab Prev Next None 1 2 3 4 5 Prev AlrmRelay Disab Next Enab Disab Prev Table C-9 General Management Configuration Options Management Configuration Options System Name Next Edit Clear Prev NMS n Access Read Next Read R/W PrevSystem Location Next Edit Clear Prev System Contact Next Edit Clear Prev Access 2 Read Next Read R/W Prev Access 1 Read Next Read R/W PrevCommunityName2 Next Edit Clear Prev IP Adr Next Edit Clear Prev Com NetMask Next Edit Clear Prev Com IP Adr Next Edit Clear PrevCom Link PPP Next PPP Slip Prev Modem IP Adr Next Edit Clear Prev Alt Mdm IP Adr Next Edit Clear Prev Mdm NetMask Next Edit Clear PrevAlt Mdm NetMask Next Edit Clear Prev Modem Link PPP Next PPP Slip Prev Aux NetMask Next Edit Clear Prev Aux IP Adr Next Edit Clear PrevIPBusMast Disab Next Enab Disab Prev Table C-9 General Management Configuration Options Num Trap Mgrs Next 1 2 3 4 5 6 Prev Table C-10 Management Trap Configuration OptionsTrapn IP Adr Next Edit Clear Prev Gen Trap Both Next Disab Warm Auth Both Prev Link Trap Both Next Disab Up Down Both Prev Entp Trap Enab Next Enab Disab PrevTrap I/F All Next NET DTE T1s Ports All Prev Value Default in Bold Configuration WorksheetsDTE Options General User Options Alarm Prt2 Options Prt1 OptionsPrt3 Options Prt4 Options Network Interface Network Channel Allocation D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 Port Chan Options Port Chan Options Mgmt Trap General Mgmt Pin Assignments D Table D-1 T1 Network Interface Connector Signal Pin NumberT1 Network Interface Figure D-1. T1 Line Interface Cable, RJ48C-to-RJ48C DTE Drop/Insert Interface Table D-2 DTE Drop/Insert DSX-1 Connector Signal Pin Number Modem Port Interface Table D-3 Integral Modem Port Connector Signal Pin Number AUX Port Interface Table D-4 AUX Port Connector Signal Direction Pin Number COM Port Interface Table D-5 COM Port Connector Signal Direction Pin Number Figure D-5. COM Port-to-PC Cable Table D-6 EIA 530A Port Interface Connector Signal Circuit EIA 530A Port Interface ConnectorDirection Pin Mnemonic Number Figure D-7. EIA 530A-to-RS449 Cable EIA 530A-to-RS449 Cable Interface Table D-7 RS449 Cable Interface Signal Circuit Figure D-8. EIA 530A-to-V.35 Cable EIA 530A-to-V.35 Cable Interface Direction Pin Number Table D-8 Cable Interface Signal Figure D-9. EIA 530A-to-X.21 Cable EIA 530A-to-X.21 Cable Interface Table D-9 Cable Interface Signal Pin Serial Crossover Cable Optional DC Power Cable Power Input ConnectorTable D-10 DC Power Connector Signal Pin Number Table D-11 External Clock Connector Signal Pin Number Snmp MIB Objects E System Group, MIB MIB II RFC Interface Group, MIB System Group ± ªsysServicesº Object system Interface Group ± ªifDescrº Object ifEntry Interface Group ± ªifOperStatusº Object ifEntry IP Group, MIB IP Group ± ªipAdEntAddrº Object ipAddrEntry IP Group ± ªipRouteDestº Object ipRouteEntry DS1/E1 MIB RFC Near End Group ± ªdsx1ValidIntervalsº Object dsx1ConfigEntry Near End Group ± ªdsx1LineStatusº Object dsx1ConfigEntry DS1 Fractional Group, DS1/E1 MIB Far End Group, DS1/E1 MIB General Port Table, RS-232-like MIB RS-232-like MIB RFC Asynchronous Port Table, RS-232-like MIB General Port Table ± ªrs232PortTypeº Object rs232PortEntry Input Signal Table, RS-232-like MIB Output Signal Table, RS-232-like MIBSynchronous Port Table, RS-232-like MIB Generic Interface Test Table, Generic Interface MIB Generic-Interface MIB Extensions RFC Enterprise MIB Correlation between Menu Commands and Snmp Objects Dsx1CurrentES Dsx1TimeElapsedDsx1CurrentUAS Dsx1CurrentSES Set dsx1LoopbackConfig for Net T1 to dsx1NoLoop Set dsx1LoopbackConfig for Net T1 to dsx1LineLoopSet dsx1LoopbackConfig for Net T1 to dsx1PayloadLoop Set dsx1LoopbackConfig for DTE T1 to dsx1LineLoop Set/Display dsx1FracNumber and dsx1Fracifindex for DTE or Set/Display dsx1FracNumber and dsx1FracIfindex for DTE T1Display rs232PortInSpeed or rs232PortOutSpeed for port n Set/Display rs232PortInSpeed or rs232PortOutSpeed for COM Acculink 316x DSU/CSU IP Network Addressing Scenarios F Figure F-1. Daisy-Chained Standalone at the Central Site Scenario 135.18.2.17 135 135 Figure F-5. Multiple COM Ports Connected to Different NMSs Front Panel Emulation G Installing Front Panel Emulation Software Starting Front Panel Emulation Async Terminal Operation H Before Using the Async Terminal Ending an Async Terminal Session Initiating an Async Terminal Session Menu Organization Main Status Test Configuration Control Table H-1 Screen Function Keys Usage Using Async Terminal ScreensTable H-2 Keyboard Keys Usage Figure H-3. Customer Identification Screen Figure H-4. Example of Display LEDs Screen Figure H-5. Configuration Load Screen Displaying or Editing Configuration Options Figure H-6. Configuration Edit/Display Screen Figure H-7. Configuration Save Screen Figure H-8. Enabling a Password Figure H-9. Setting a Password Figure H-10. Entering a Password Network Interface Options Front Panel Configuration Worksheets for the Async Terminal InterfaceEquivalent DTE Interface Options Front Panel Sync Data Port Options Port Sync Data Port Options Port Front PanelFront Panel Async Terminal Operation General Options Front Panel Value Default in BoldUser Interface Front Panel Options Equivalent Telnet Sessions Options Equivalent External Device Options EquivalentInternal Modem Options Equivalent Auxiliary Port Options Equivalent Alarm & Trap Options Front PanelPort Use Aux Use None, Mgmt, Daisy Communication Protocol Options Equivalent Management and Communication Front PanelGeneral Snmp Management Options Equivalent Snmp Traps Options Equivalent Snmp NMS Security Options Equivalent Equipment List Equipment Feature NumberCable numbers for DSU/CSU are located Acculink 316x DSU/CSU Acami allocation method Glossary AWG CRC6 DSR ISO LCP PDU RTS TXC Acculink 316x DSU/CSU Glossary-10 Index Index-2 Index Index-4 Index-5 Index-6