Important Instructions | Paradyne 3160-A2-GB21-50 guide

Installation

Important Instructions

Read and follow all warning notices and instructions marked on the DSU/CSU or included in this guide.

For a complete listing of the safety instructions, see the Important Safety Instructions section at the beginning of this guide.

HANDLING PRECAUTIONS

FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, take proper static control precautions to prevent damage to equipment. If you are not sure of the proper static control precautions, contact your nearest sales or service representative.

Optional Power Sources

The DSU/CSU is typically powered by the ac power module. Use the following procedures only if you want to use an optional dc power source.

Using the optional dc power cable, the DSU/CSU is capable of operating on either a +24 Vdc power source,

±48 Vdc single source battery, or ± 48 Vdc redundant source batteries (for power backup). To use dc power, choose one of the following power supply types.

Installing the +24 Vdc Power Supply

To install the DSU/CSU using a +24 Vdc power supply, refer to Figure 2-9and use the following procedure.

To install the +24 Vdc power supply,

1.Connect the green wire to a suitable earth ground.

2.Connect the white wire to the +24 Vdc return.

3.Connect the orange wire to the +24 Vdc source.

4.Cut the black, red, and blue wires off at the outer insulation.

5.Plug the power connector into the DSU/CSU.

DSU/CSU POWER
	PLUG			TO CUSTOMER-SUPPLIED BATTERY
			BLACK
	1			X
			RED
	2			X
			GREEN
	3				EARTH GROUND
			WHITE
	4				+24 VDC RETURN
			ORANGE
	5				+24 VDC SOURCE
			BLUE
	6			X

496-14298-01

Figure 2-9. +24 Vdc Power Supply Pinouts

3160-A2-GB21-50

January 1997

2-5

Image 24

Paradyne 3160-A2-GB21-50 manual Important Instructions, Optional Power Sources, Installing the +24 Vdc Power Supply

Contents

Area Code Change Acculink 316X Data Service Unit Channel Service Unit Warranty, Sales, and Service Information TrademarksOperators Guide 3160-A2-GB21-50 Copyright 1997 Paradyne Corporation. All rights reserved Important Safety Instructions Government Requirements and Equipment Return United States315x CSU Facility Interface Codes Description Canada Important Instructions Acculink 316x DSU/CSU Table of Contents Glossary Index Preface Objectives and Reader AssumptionsRelated Documents Reference Documents Acculink 316x DSU/CSU Features IntroductionOverview Telnet Access Alarm Message CapabilityDTE Drop/Insert DSX-1 Interface Front Panel Emulation Physical Description Standalone DSU/CSU Front Panel 3164 Standalone DSU/CSU Rear Panel DSU/CSU Rear Panel AUX Port Installation Application Examples Network Snmp or Telnet Connection Examples EDL is only available on 2-port and 4-port DSU/CSUs Connection through a LAN Adapter Optional Power Sources Installing the +24 Vdc Power SupplyImportant Instructions Installing the Single ±48 Vdc Power Supply 10. ±48 Vdc Single Source Power Supply Pinouts Installing the Redundant ±48 Vdc Power Supply 11. ±48 Vdc Redundant Source Power Supply Pinouts Cabling Examples 12. Cabling Examples Power-Up Self-Test Self-Test ProgressSelf-Test Passed Self-Test Acculink 316x DSU/CSU January Operation LCD Using the Front Panel Standalone DSU/CSU Front Panel Keypad LCD LEDs Test Jacks System LEDs Name Color MeaningNetwork Interface LEDs DTE Drop/Insert DSX-1 Interface LEDs Name Color Meaning PDV Data Port LEDs DTR Displaying Unit Identity Status TStat LED IDIdentity Identity Cust ID=xxxxxxxx Setting Customer Identification Selecting the DTE Drop/Insert or Data Port for LED Display Displaying LED Conditions Status Perf TStat LEDSelect LEDs T1 Prt1 Prt2 LED Display Test NetSig Changing Configuration Options Displaying/Editing Configuration Options Load from Activ Cust1Choose Funct Edit Save Edit DTE Port NET Saving Edit Changes Selecting/Copying to a Specific PortSave Edit to Activ Cust1 Port Select Copy Prt1 Prt2 Configuring the DSU/CSU for Snmp or Telnet Access Selecting the PortCopy From Prt1 Prt2 Prt3 Copy To All Prt1 Prt2 Setting the IP Address Edit User Alarm MgmtMgmt Config Gen Trap Edit Chan Gen User Selecting the Link Layer Protocol Com IP Adr Next Edit Clear000.000.000.000 Up Down Save 010.155.111.222 Up Down Save Specifying the Community Names and Access Types Com Link Next PPP Slip Access Next Read R/W CommunityName1 Next Edit ClearPublic Up Down Save Configuring Snmp Traps Enabling Snmp Trap MessagesSelecting the Number of Trap Managers Snmp Trap Next Enab Disab Configuring a Destination for Snmp Traps Num Trap Mgrs1 NextTrapn Dst Next None Com Configuring DS0 Channels Example of Channel Allocation Network Interface Network Channel Allocation Example of Interface Worksheet DTE Chan Assign Voice Config N1 ± RBS or Data Example of RBS Information Worksheet Port Channel Configuration Worksheet Ports 1 Port Chan Options Value Conf 10. Port Channel Configuration Worksheet Ports 3 Display Channel Symbols Symbol MeaningDisplaying DS0 Channel Assignments Channel Config Prt1 Prt2 Prt3 Allocating Data PortsEditDTE Port Chan Block or Acami Assignment Method Assign ToNET Next NET DTEAssign By Next Block Acami Port Rate384 Next 64 Individual Channel Assignment Method Assign ByBlock Next Block AcamiAssign ByChan Block Acami Chan Next Prt1 Prt2 DTE Channels Assign Voice Providing Backup Capability Clearing DS0 Channel AllocationClear Channel Port1 11. Common Clocking Configurations Selecting the Timing Source Configuring for Network Timing Configuring for External Timing Establishing Access Security on a Port Setting a PasswordPasswordNone Next None Com Control Reset CID Passwd Entering a Password to Gain Access Acquiring/Releasing User InterfaceAcquiring the Active User Interface Passwd Up Down Done FP Access Next Enab Disab Enabling/Disabling the Front PanelReleasing the Active User Interface Using the Integral Modem in Standalone DSU/CSUs Call Setup Pass Dial ChDirEntering Numbers in the Phone Directories Xxxxxxxxxxxxxxxxx Next Prev Edit Xxxxxxxxxxxxxxxxx Up Down Save Initiating a Call for Front Panel Pass-Through Operation Up Down Dial Disconnecting the Modem Connection Call Setup Disc ChDirDisconnect Command Complete Enabling the Communication Port for Carrier-Mounted DSU/CSUs Com Port Next Enab Disab Control Sequences Ascii HEX Deactivating the Alarm Relay for Carrier-Mounted DSU/CSUs Resetting the DSU/CSUDownload Operations Acculink 316x DSU/CSU January User Interface Access Security for Standalone DSU/CSUs Changing User Interface Access SecuritySecurity Lvl1 Lvl2 Acculink 316x DSU/CSU January Maintenance Self-Test Health Status DevHS STest PerfSTest Health Passed Self-Test Health Messages Device Health and Status Device H/S OOF at DTEAuto Dev H/S OOF at DTE Health and Status Messages Health and Status Messages Performance Reports Performance Telco User Prt1User Registers Cur 24Tot Intvl User Current Event = xx,xxx User 24 Hour VldIntvl = User Intvl Up Down DsplyUser Intvl ES=xxx Control Rel CurTimer EventVldIntvl StEvnt Complete Alarms Snmp Traps Enterprise-Specific Trap Definitions Trap Value EventSnmp Trap per Interface Trap Meaning Troubleshooting Troubleshooting Symptom Possible Cause SolutionsYellow at Net Yellow at DTE AIS at DTE X x x x x Test Jacks Control Passwd MonMon Jack Eqpt Test Jack Functions Test Jack Name Function Test Commands Remote Loopback TestsSending a Line Loopback Up or Down Test Rlpbk Lpbk Ptrns Sending a V.54/ANSI FT1 Activation/Deactivation Rem Loop Type Prt1 Prt2 Prt3 Local Loopback Tests Valid Loopback Combinations Starting a Line Loopback Starting a Payload LoopbackLoopback Abort LLB PLB Starting a DTE Loopback Starting a Repeater LoopbackLoopback Starting a Data Channel Loopback Starting a Data Terminal LoopbackLoopback Dclb Prt1 Prt2 Prt3 Aborting Loopbacks Loopback Dtlb Prt1 Prt2 Prt3Loopback Abort All Test Patterns Sending Test Patterns Monitoring Test Patterns Patterns Mon QrssMonitor Name NET Prt1 Prt2 Qrss Network Qrss Port Aborting Test Patterns Patterns Abort All Send Mon Lamp Test Starting a Lamp TestAborting a Lamp Test Displaying DSU/CSU Test Status Status STest Perf TStatTest Status Messages Front Panel Menu a DSU ESF 3160-A2-GB21-50 Technical Specifications B Models 3160/3164 Port Interface Configuration Options C DTE Interface Configuration Options DTE Interface Configuration Options Table C-1 DTE Interface Configuration OptionsDTE Port Enab Next Enab Disab Prev DTE Framing ESF Factory 1 D4 Factory Next D4 ESF Prev Extrn DLB Disab Next Enab Disab Prev Send Ones Enab Next Enab Disab Prev Port Configuration Options Port Configuration OptionsTable C-2 Port Type E530 Factory Next E530 V.35 RS449 Prev Table C-2 Port Configuration Options All Ones Both Next Disab DTR RTS Both PrevRcv Yellow Halt Next None Halt Prev Tx Clock Int Next Int Ext Prev InvertTxC Disab Next Enab Disab Prev InvrtData Disab Next Enab Disab PrevEDL Disab Next Enab Disab Prev Err Rate 10E-4 Next 10E-4 10E-5 10E-6 10E-7 10E-8 10E-9 Prev Near-end Disab Next Disab Maint Send Both Prev Far-end Disab Next Disab Maint Prev Mgmt Link Disab Next Enab Disab Prev Network Interface Configuration Options Table C-3 Network Interface Configuration Options NET LLB Enab Next Enab Disab Prev NET PLB Enab Next Enab Disab PrevBit Stuff Next 62411 Part68 Disab Prev Circuit Ident Next Edit Clear Prev Channel Configuration Options Table C-4 DTE Channel Configuration Options Table C-5 Data Port Channel Configuration Options Channel Config Dsply Clear DTE Prt1 Prt2 Prt3 Prt4Assign To NET Next NET DTE Prtn Prtn Prtn Prev Assign By Block Next Block Acami Chan Prev Port Rate Next 128 192 256 320 384 448 576 640 704 768 832 896 960 10881216 1280 1344 1472 1536 Prev Next 112 168 224 280 336 392 N10 N11 N12 N24 Next Prev D10 D11 D12 D24 General Configuration Options Table C-6 General Configuration OptionsGen Yellow Enab Next Enab Disab Prev Clock Src NET Next NET DTE Prt1 Int Ext Prev Tst Timeout Enab Next Enab Disab Prev Tst Duration Next Up Down Save Prev User Interface Configuration Options Table C-7 User Interface Configuration Options Password None Next None Com Modem Both Prev Com Port Disab Next Enab Disab PrevCom Use Ascii Next Mgmt Ascii Daisy Term Prev ComExtDev Disab Next Disab AT Other Prev ComConnPrefix Next Edit Clear Prev ComConnected Next Edit Clear PrevComEscapeSeq Next Edit Clear Prev ComEscDel None Next None 0.2s 0.4s 0.6s 0.8s 1.0s Prev ComDisconnect Next Edit Clear PrevCom Type Async Next Async Sync Prev Com Clk Int Next Int Ext Prev Com Rate Next 1.2 2.4 4.8 9.6 14.4 19.2 38.4 Prev Char Length Next 7 8 PrevCParity None Next None Even Odd Prev CStop Bits Next 1 1.5 2 Prev CmDiscTm Next Up Down Save Prev Modem Use Ascii Next Mgmt Ascii Term PrevModem Type Async Next Async Sync Prev Modem Rate Next 1.2 2.4 Prev MStop Bits Next 1 2 Prev LSpaceDsc Disab Next Enab Disab PrevMInActTm Disab Next Enab Disab Prev MDiscTm Next Up Down Save Prev Aux Rate Next 9.6 14.4 19.2 38.4 Prev TnSession Disab Next Enab Disab PrevTnPaswd Disab Next Enab Disab Prev TnInActTm Disab Next Enab Disab Prev Alarm Configuration Options Table C-8 Alarm Configuration OptionsAlrm Msg Disab Next Disab Modem Com Both Prev Snmp Trap Disab Next Enab Disab Prev Dial Delay Next 1 2 3 4 5 6 7 8 9 10 Prev DialOut Disab Next Enab Disab PrevCall Retry Disab Next Enab Disab Prev Next None 1 2 3 4 5 Prev AlrmRelay Disab Next Enab Disab Prev Management Configuration Options Table C-9 General Management Configuration Options NMS n Access Read Next Read R/W Prev System Name Next Edit Clear PrevSystem Location Next Edit Clear Prev System Contact Next Edit Clear Prev Access 1 Read Next Read R/W Prev Access 2 Read Next Read R/W PrevCommunityName2 Next Edit Clear Prev IP Adr Next Edit Clear Prev Com IP Adr Next Edit Clear Prev Com NetMask Next Edit Clear PrevCom Link PPP Next PPP Slip Prev Modem IP Adr Next Edit Clear Prev Mdm NetMask Next Edit Clear Prev Alt Mdm IP Adr Next Edit Clear PrevAlt Mdm NetMask Next Edit Clear Prev Modem Link PPP Next PPP Slip Prev Aux IP Adr Next Edit Clear Prev Aux NetMask Next Edit Clear PrevIPBusMast Disab Next Enab Disab Prev Table C-9 General Management Configuration Options Table C-10 Management Trap Configuration Options Num Trap Mgrs Next 1 2 3 4 5 6 PrevTrapn IP Adr Next Edit Clear Prev Gen Trap Both Next Disab Warm Auth Both Prev Entp Trap Enab Next Enab Disab Prev Link Trap Both Next Disab Up Down Both PrevTrap I/F All Next NET DTE T1s Ports All Prev Configuration Worksheets Value Default in BoldDTE Options General Alarm User Options Prt1 Options Prt2 OptionsPrt3 Options Prt4 Options Network Interface Network Channel Allocation D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 Port Chan Options Port Chan Options General Mgmt Mgmt Trap Table D-1 T1 Network Interface Connector Signal Pin Number Pin Assignments DT1 Network Interface Figure D-1. T1 Line Interface Cable, RJ48C-to-RJ48C Table D-2 DTE Drop/Insert DSX-1 Connector Signal Pin Number DTE Drop/Insert Interface Table D-3 Integral Modem Port Connector Signal Pin Number Modem Port Interface Table D-4 AUX Port Connector Signal Direction Pin Number AUX Port Interface Table D-5 COM Port Connector Signal Direction Pin Number COM Port Interface Figure D-5. COM Port-to-PC Cable EIA 530A Port Interface Connector Table D-6 EIA 530A Port Interface Connector Signal CircuitDirection Pin Mnemonic Number EIA 530A-to-RS449 Cable Interface Figure D-7. EIA 530A-to-RS449 Cable Table D-7 RS449 Cable Interface Signal Circuit EIA 530A-to-V.35 Cable Interface Figure D-8. EIA 530A-to-V.35 Cable Table D-8 Cable Interface Signal Direction Pin Number EIA 530A-to-X.21 Cable Interface Figure D-9. EIA 530A-to-X.21 Cable Table D-9 Cable Interface Signal Serial Crossover Cable Pin Power Input Connector Optional DC Power CableTable D-10 DC Power Connector Signal Pin Number Table D-11 External Clock Connector Signal Pin Number Snmp MIB Objects E MIB II RFC System Group, MIB System Group ± ªsysServicesº Object system Interface Group, MIB Interface Group ± ªifDescrº Object ifEntry Interface Group ± ªifOperStatusº Object ifEntry IP Group ± ªipAdEntAddrº Object ipAddrEntry IP Group, MIB IP Group ± ªipRouteDestº Object ipRouteEntry DS1/E1 MIB RFC Near End Group ± ªdsx1ValidIntervalsº Object dsx1ConfigEntry Near End Group ± ªdsx1LineStatusº Object dsx1ConfigEntry Far End Group, DS1/E1 MIB DS1 Fractional Group, DS1/E1 MIB RS-232-like MIB RFC General Port Table, RS-232-like MIB General Port Table ± ªrs232PortTypeº Object rs232PortEntry Asynchronous Port Table, RS-232-like MIB Output Signal Table, RS-232-like MIB Input Signal Table, RS-232-like MIBSynchronous Port Table, RS-232-like MIB Generic-Interface MIB Extensions RFC Generic Interface Test Table, Generic Interface MIB Correlation between Menu Commands and Snmp Objects Enterprise MIB Dsx1TimeElapsed Dsx1CurrentESDsx1CurrentUAS Dsx1CurrentSES Set dsx1LoopbackConfig for Net T1 to dsx1LineLoop Set dsx1LoopbackConfig for Net T1 to dsx1NoLoopSet dsx1LoopbackConfig for Net T1 to dsx1PayloadLoop Set dsx1LoopbackConfig for DTE T1 to dsx1LineLoop Set/Display dsx1FracNumber and dsx1FracIfindex for DTE T1 Set/Display dsx1FracNumber and dsx1Fracifindex for DTE orDisplay rs232PortInSpeed or rs232PortOutSpeed for port n Set/Display rs232PortInSpeed or rs232PortOutSpeed for COM Acculink 316x DSU/CSU IP Network Addressing Scenarios F Scenario Figure F-1. Daisy-Chained Standalone at the Central Site 135.18.2.17 135 135 Figure F-5. Multiple COM Ports Connected to Different NMSs Installing Front Panel Emulation Software Front Panel Emulation G Starting Front Panel Emulation Before Using the Async Terminal Async Terminal Operation H Initiating an Async Terminal Session Ending an Async Terminal Session Main Status Test Configuration Control Menu Organization Using Async Terminal Screens Table H-1 Screen Function Keys UsageTable H-2 Keyboard Keys Usage Figure H-3. Customer Identification Screen Figure H-4. Example of Display LEDs Screen Displaying or Editing Configuration Options Figure H-5. Configuration Load Screen Figure H-6. Configuration Edit/Display Screen Figure H-7. Configuration Save Screen Figure H-8. Enabling a Password Figure H-9. Setting a Password Figure H-10. Entering a Password Configuration Worksheets for the Async Terminal Interface Network Interface Options Front PanelEquivalent DTE Interface Options Front Panel Sync Data Port Options Port Front Panel Sync Data Port Options PortFront Panel Async Terminal Operation Value Default in Bold General Options Front PanelUser Interface Front Panel Options Equivalent External Device Options Equivalent Telnet Sessions Options EquivalentInternal Modem Options Equivalent Alarm & Trap Options Front Panel Auxiliary Port Options EquivalentPort Use Aux Use None, Mgmt, Daisy Management and Communication Front Panel Communication Protocol Options EquivalentGeneral Snmp Management Options Equivalent Snmp NMS Security Options Equivalent Snmp Traps Options Equivalent Equipment Feature Number Equipment ListCable numbers for DSU/CSU are located Acculink 316x DSU/CSU Glossary Acami allocation method AWG CRC6 DSR ISO LCP PDU RTS TXC Acculink 316x DSU/CSU Glossary-10 Index Index-2 Index Index-4 Index-5 Index-6