Mesh Statistics | Proxim AP-4000 specs

Monitoring	AP-4000 Series User Guide
Station Statistics

The following stations statistics are available through SNMP:

•Octets Received: The number of octets received from the associated wireless station (or WDS link partner) by the AP.

•Unicast Frames Received: The number of Unicast frames received from the associated wireless station (or WDS link partner) by the AP.

•Non-Unicast Frames Received: The number of Non-Unicast frames received (i.e. broadcast or multicast) from the associated wireless station (or WDS link partner) by the AP.

•Octets Transmitted: The number of octets sent to the associated wireless station (or WDS link partner) from the AP.

•Unicast Frames Transmitted: The number of Unicast frames transmitted to the associated wireless station (or WDS link partner) from the AP.

Mesh Statistics

This tab displays statistics relating to the Mesh portal: the network topology or the Neighbor Table. Selecting Network Topology displays a tree structure representing the Mesh network. Selecting Neighbor Table (shown below) displays the MAC address, channel, path cost, number of hops, RSSI, type, and status of all Mesh APs within range of the AP.

Figure 5-10 Mesh Statistics Monitoring Tab (Neighbor Table)

138

Image 138

Proxim manual Mesh Statistics, Monitoring AP-4000 Series User Guide Station Statistics

Contents

ORiNOCO AP-4000 Series Access Points User Guide OpenSSL License Note CopyrightTrademarks AP-4000 Series User Guide Contents System Status 4 Advanced Configuration Contents AP-4000 Series User Guide Commands TroubleshootingMonitoring Command Line Interface CLI Recovery Procedures Ascii Character Chart C Specifications Statement of WarrantyTechnical Support Regulatory Compliance Products Covered in this User Guide Document ConventionsProduct Description Introduction to Wireless Networking Introduction AP-4000 Series User Guide Mesh Networking AP-4000M/4900M Only Mesh Network Convergence Mesh Startup Topology Example Step Mesh Network Configuration Guidelines for Roaming Management and Monitoring Capabilities Ieee 802.11 SpecificationsCommand Line Interface HTTP/HTTPS Interface Snmp Management SNMPv3 Secure Management SSH Secure Shell Management AP-4000 Series Hardware Description Overview Antennas External Antennas Installation and Initialization AP-4000 Series User Guide Active EthernetGHz Antenna LED Indicators LED Indicators on the AP-4000/4000M/4900M Top Panel Prerequisites General Prerequisites Mesh Prerequisites Product Package System Requirements Hardware Installation Required MaterialsCabling the AP-4000/4000M/4900M Installing the Security Cover Mounting the AP-4000/4000M/4900M Mounting the AP-4000/4000M/4900M to a Ceiling Mounting the AP-4900M in a Vehicle Installing External Antennas Opening the Antenna Compartment Installing the AP in a Plenum Attaching Antennas to the AP-4900M for 4.9 GHz OperationPage Using ScanTool InitializationScanTool Instructions Scan List Click LAN Settings LoggingSelect Tools Internet Options 11 Enter Network Password Using the Setup Wizard 12 System Status ScreenPage Installing the Software Download the Software Install Software with Http Interface Click Commands Update AP via Http Click Commands Reboot Install Software with Tftp Server Install Updates from your Tftp Server using the CLI Related Topics System Status Advanced Configuration Advanced Configuration AP-4000 Series User Guide Configure Main Screen System Dynamic DNS SupportPage IP Configuration Network Dhcp Server DNS ClientAdvanced Advanced Configuration AP-4000 Series User Guide Network Start IP Address End IP AddressComment optional Dhcp Relay Agent Dhcp Relay Agent Dhcp Server IP Address Table Link Integrity Target IP Address Comment optional Link Integrity Configuration Screen Sntp Simple Network Time Protocol Sntp Configuration Screen Advanced Configuration AP-4000 Series User Guide Network Operational Mode Interfaces Advanced Configuration AP-4000 Series User Guide Interfaces Super Mode and Turbo ModeIeee 802.11d Support for Additional Regulatory Domains Configuring 802.11d Support TX Power Control/Transmit Power LevelConfiguring TX Power Control Wireless-A 802.11a Radio and Wireless-B 802.11b/g Radio 10 Wireless Interface a Advanced Configuration AP-4000 Series User Guide Interfaces Dynamic Frequency Selection/Radar Detection DFS/RD Wireless Service Status Affected CountriesRTS/CTS Medium Reservation Traps Generated During Wireless Service Shutdown and Resume Click on Configure Interfaces Wireless a or Wireless BChannel Blacklist Table 13 WDS Example WDS Setup Procedure Bridging WDS Ethernet 15 Adding WDS Links 16 Ethernet Sub-tab Mesh AP-4000M/AP-4900M Only 17 Mesh Sub-tab AP-4000M/AP-4900M Mesh Software Kit 18 Mesh Sub-tab AP-4000 Passwords Management IP Access Table ServicesSecure Management Advanced Configuration AP-4000 Series User Guide Management Https Access Secure Socket LayerAccessing the AP through the Https interface 19 Management Services Configuration Screen SSH Session Setup Configuring SSHSSH Clients Click Commands Update AP via Http or via Tftp Uploading Externally Generated Host Keys Serial Configuration Settings Radius Based Management Access Automatic Configuration AutoConfig Auto Configuration and the CLI Batch FileSet up Automatic Configuration for Static IP 21 Automatic Configuration Screen Set up Automatic Configuration for Dynamic IP Hardware Configuration Reset Chrd 22 Dhcp Options Setting the Boot Server Host Name Configuration Reset via Serial Port During Bootup Configuring Hardware Configuration ResetClick Configure Management Chrd Procedure to Reset Configuration via the Serial Interface Static MAC FilteringEthernet Protocol Select the Filter Operation Type Advanced Configuration AP-4000 Series User Guide Filtering Wired MAC Address Wired MAC Address 0040F41CDB6AWireless MAC Address 00022D5194E4 Wireless MAC Address 0020A6124E38 Number AdvancedTCP/UDP Port Click Add under the TCP/UDP Port Filter Table heading Editing TCP/UDP Port Filters Click Edit under the TCP/UDP Port Filter Table heading Alarms Groups Security Trap Group Trap Name Description Severity Level Operational Trap Group Trap Name Description Severity Level Trap Name Description Severity Level Flash Memory Trap Group Trap Name Description Severity Level Sntp Trap Group Trap Name Description Severity Level Tftp Trap Group Trap Name Description Severity LevelImage Trap Group Trap Name Description Severity Level Generic Trap Group Trap Name Description Severity Level Alarm Host Table RFC 1215-Trap Trap Name Description Severity Level Configuring Syslog Event Notifications SyslogEvent Priority Description Advanced Configuration AP-4000 Series User Guide Alarms Syslog MessagesSyslog Message Name Priority Severity Description Advanced Configuration AP-4000 Series User Guide Rogue Scan Continuous Scanning Mode Background Scanning ModeMulti-Band Scanning Click Configure Alarms Rogue Scan Rogue Scan Data CollectionRogue Scan 28 Rogue Scan Screen Bridge Spanning Tree Advanced Configuration AP-4000 Series User Guide Bridge Storm Threshold Configuring Interfaces for Packet Forwarding Intra BSSPacket Forwarding QoS Wireless Multimedia Extensions WME/Quality of Service QoSClick Configure QoS Policy Enabling QoS and Adding QoS policies Advanced Configuration AP-4000 Series User Guide QoS Enter the Priority Mapping Index101 Click Configure QoS Priority Mapping Priority Mapping102 Enhanced Distributed Channel Access Edca STA Edca Table and AP Edca Table103 Click Configure QoS Edca 104 105 Radius Servers per Authentication Mode and per Vlan Radius Profiles106 Configuring Radius Profiles Radius Servers Enforcing Vlan Access Control107 108 37 Add Radius Server Profile 109 Radius Accounting MAC Access Control Via Radius Authentication802.1x Authentication using Radius Session Length Authentication Attributes Accounting Attributes111 112 SSID/VLAN/Security Vlan Overview113 114 Click Configure SSID/VLAN/Security Mgmt Vlan Typical User Vlan ConfigurationsControl Access to the AP Management Vlan Provide Access to a Wireless Host in the Same Workgroup Disable Vlan TaggingSecurity Profile Authentication Process Wi-Fi Protected Access WPA/802.11i WPA2117 Authentication Protocol Hierarchy 118 Configuring Security Profiles Click Configure SSID/VLAN/Security Security ProfileVLANs and Security Profiles 802.1x Station Non Secure StationWEP Station WPA Station 802.11i-PSK Station 121 42 Security Profile Table Add Entries 122 MAC Access Wireless-A or Wireless-B123 Configuring an SSID/VLAN with Vlan Tagging Disabled 124 45 SSID/VLAN Edit Entries Screen Vlan Tagging Disabled 125 Configuring SSID/VLANs with Vlan Tagging Enabled Click SSID/VLAN/Security Wireless-A or Wireless-B126 47 SSID/VLAN Edit Entries Screen Vlan Tagging Enabled 127 Broadcast Ssid and Closed System 128 Monitor Main Screen 129 Version Monitoring AP-4000 Series User Guide IP/ARP Table Icmp Monitoring Tab Learn Table Learn Table Monitoring Tab Radius 134 Monitoring AP-4000 Series User Guide Interfaces 135 136 Station Statistics 137 Mesh Statistics Monitoring AP-4000 Series User Guide Station Statistics Introduction to File Transfer via Tftp or Http 139 Http File Transfer Guidelines Image Error Checking During File TransferTftp File Transfer Guidelines 140 Commands AP-4000 Series User Guide Update APUpdate AP via Tftp 141 Update AP via Http Commands AP-4000 Series User Guide Update AP142 Retrieve File via Tftp Commands AP-4000 Series User Guide Retrieve FileRetrieve File 143 Retrieve File via Http 144 Retrieve File via Http Command Screen Reboot ResetCommands AP-4000 Series User Guide Reboot 13 Help Link Configuration Screen 147 Help Link Connectivity Issues Troubleshooting ConceptsSymptoms and Solutions AP Unit Will Not Boot No LED Activity Basic Software Setup and Configuration Problems Client Connection Problems Vlan Operation Issues Active Ethernet AE Recovery Procedures Reset to Factory Default ProcedureForced Reload Procedure Preparing to Download the AP Image Download a New Image Using ScanToolDownload Procedure 153 Download a New Image Using the Bootloader CLI 154 Hardware and Software Requirements Setting IP Address using Serial PortInitializing the IP Address using CLI Attaching the Serial Port Cable Radius Authentication Server Related Applications156 Tftp Server 157 Notation Conventions General NotesPrerequisite Skills and Knowledge Important Terminology Navigation and Special Keys CLI Error MessagesError Message Description Key Combination Operation Command Line Interface CLI AP-4000 Series User Guide Command Line Interface CLI VariationsBootloader CLI 160 CLI Command Types Operational CLI CommandsExample 1. Display Command list Example 2. Display specific Commands Example 3. Display parameters for set and showExample 3a. Display every parameter that can be changed Done, exit, quit Example 3b. Display parameters based on letter sequenceExample 4. Display Prompts for Successive Parameters Download Passwd HelpHistory 164 Search Parameter Control CommandsShow CLI Command 165 Set and show Command Examples Set CLI CommandConfiguring Objects that Require Reboot Examples Example 2 Create a table entry or row Example 1 Set the Access Point IP Address ParameterExample 4 Enable, Disable, or Delete a table entry or row Example 3 Modify a table entry or row Example 5 Show the Group Parameters Example 6 Show Individual and Table Parameters168 Working with Tables Using Tables and StringsUsing Strings 169 Log into the AP using HyperTerminal Configuring the AP using CLI commandsSet Basic Configuration Parameters using CLI Commands Log into the AP using Telnet Set System Name, Location and Contact Information Change PasswordsSet Network Names for the Wireless Interface 171 Country Code 172 Configure SSIDs Network Names, VLANs, and Profiles 173 Set up Auto Configuration Download an AP Configuration File from your Tftp ServerBackup your AP Configuration File 174 Other Network Settings Configure the AP as a Dhcp ServerConfigure the DNS Client Operational Mode Autochannel Select ACS Enable/Disable Super Mode 802.11a/g only Enable/Disable Closed SystemShutdown/Resume Wireless Service Enable/Disable Turbo Mode 802.11a/g only Edit Management IP Access Table Configure Management PortsSet the Distance Between APs Configure Serial Port Interface Configure Secure Socket Layer HttpsSet Telnet Session Timeouts Set Communication Ports Setup MAC Address Access Control Create/Enable WDSEnable/Disable WDS Add an Entry to the MAC Access Control Table Configure Radius Authentication servers Set Radius Parameters181 Set Hardware Configuration Reset Parameters 182 Configure a Security Profile with Non Secure Security Mode Enable Vlan ManagementDisable Vlan Management Configure a Security Profile with WEP Security Mode CLI Monitoring Parameters Configure a Security Profile with 802.11i Security ModeConfigure a Security Profile with 802.11i-PSK Security Mode Parameter Tables Serial Port Parameters Serial Port setup 185 186 System Parameters Name Type Value Access CLI ParameterSet sysresettodefaults 187 Network Parameters DNS Client for Radius Name ResolutionDhcp Server Parameters Name Type Value Access CLI Parameter 188 Dhcp Relay Server Table Dhcp Server table for IP poolsDhcp Relay Group 189 Sntp Parameters Name Type Value Access CLI Parameter Link Integrity IP Target Table190 Common Parameters to 802.11a/b/g Wireless Interface ParametersInterface Parameters 191 802.11a Only Parameters 192 802.11b Only Parameters 802.11b/g Only Parameters193 For 802.11b-only For 802.11g-only modeFor 802.11b/g mode Mode Channel Blacklist Parameters Wireless Distribution System WDS ParametersWireless Interface SSID/VLAN/Profile Parameters 195 Wireless Distribution System WDS Security Table Parameters 196 Snmp Parameters Name Type Value Access CLI Parameter Management Parameters197 198 Http Parameters Name Type Value Access CLI Parameter Telnet Parameters Name Type Value Access CLI Parameter199 SSH Parameters Serial Port Parameters Name Type Value Access CLI ParameterRadius Based Management Access Parameters 200 IP Access Table Parameters Tftp Server Parameters201 Filtering Parameters Ethernet Filtering Table202 TCP/UDP Port Filtering Table Proxy ARP Parameters Name Type Value Access CLI ParameterTCP/UDP Port Filtering 203 Alarms Parameters Snmp Table Host Table Parameters204 Syslog Parameters Syslog Host Table205 Bridge Parameters Spanning Tree Priority and Path Cost Table206 Packet Forwarding Parameters Storm Threshold TableIntra BSS Subscriber Blocking 207 General Radius Parameters Radius Server Configuration ParametersRadius Parameters 208 MAC Access Control Table Security Parameters Security Profile Table 210 Other Parameters Iapp Parameters Name Type Value Access CLI ParameterVLAN/SSID Parameters 211 Specifying the Mapping between 802.1p and 802.1D Priorities Enabling QoS Name Type Value Access CLI ParameterConfiguring QoS Policies 212 QoS Enhanced Distributed Channel Access Edca Parameters 213 CLI Batch File Format and Syntax Auto Configuration and the CLI Batch FileCLI Batch File Sample CLI Batch File Reboot Behavior CLI Batch File Error Log215 Hex Charact Equival Ent 216 Radius Based Management Access 217 Software FeaturesFeature Supported by AP-4000 Series Number of Stations per BSS Advanced Bridging Functions Medium Access Control MAC FunctionsSpecifications AP-4000 Series User Guide Software Features Security Functions Specifications AP-4000 Series User Guide Network Functions219 Hardware Specifications Available Channels AP-4000/4000M Channels221 AP-4900M Channels a/b/g Modes AP-4900M Channels 4.9 GHz Public Safety ModeAP-4900M Channels 222 223 Online Support Software and Documentation Downloads Knowledgebase 224 Telephone Support International 225 Limitations of Warranty Warranty CoverageRepair or Replacement Support Procedures Search Knowledgebase Ask a Question or Open an IssueOther Information Other Adapter Cards Product Model Numbers 228 Regulatory Compliance AP-4000 Series User Guide 229 Safety Information USA, Canada, & European Union 230 Federal Communications Commission FCC AP-4000/4000M 231 Modifications 232 Industry Canada IC AP-4000/4000M only 233 European Union AP-4000/4000M only 234 Country Certification/Reference No Regulatory Compliance Certifications Summary AP-4000/4000MRegulatory Compliance Certifications Summary AP-4900M 235