MAC Access, Wireless-A or Wireless-B, 123 | Proxim AP-4000 specs

Advanced Configuration

AP-4000 Series User Guide

SSID/VLAN/Security

MAC Access

The MAC Access sub-tab allows you to build a list of stations, identified by their MAC addresses, authorized to access the network through the AP. The list is stored inside each AP within your network. Note that you must reboot the AP for any changes to the MAC Access Control Table to take effect. Up to 1000 entries can be made in the table.

The “MAC ACL Status” parameter (configurable on the SSID/VLAN > Wireless A or B sub-tab) is per VLAN if VLAN Management is enabled. All other parameters besides “MAC ACL Status” are configured per AP, even if VLAN is enabled.

The following list details the configurable MAC Access parameters.

NOTE: MAC Access Control status is enabled or disabled when configuring each Security Profile.

•Operation Type: Choose between Passthru and Block. This determines how the stations identified in the MAC Access Control Table are filtered.

•If set to Passthru, only the addresses listed in the Control Table will pass through the bridge.

•If set to Block, the bridge will block traffic to or from the addresses listed in the Control Table.

•MAC Access Control Table: Click Add to create a new entry. Click Edit to change an existing entry. Each entry contains the following field:

– MAC Address: Enter the wireless client’s MAC address.

– Comment: Enter an optional comment such as the client’s name.

– Status: The entry is enabled automatically when saved (so the Status field is only visible when editing an entry). You can also disable or delete entries by changing this field’s value.

NOTE: For larger networks that include multiple Access Points, you may prefer to maintain this list on a centralized location using the MAC Access Control Via RADIUS Authentication.

Figure 4-43 MAC Access Configuration Screen

Wireless-A or Wireless-B

Each SSID can have its own Security Profile that defines its security mode, authentication mechanism, and encryption, so that customers can have multiple types of clients (non-WEP, WEP, 802.1x, WPA, WPA-PSK, 802.11i, 802.11i-PSK) on

123

Image 123

Proxim AP-4000 manual MAC Access, Wireless-A or Wireless-B, 123

Contents

ORiNOCO AP-4000 Series Access Points User Guide AP-4000 Series User Guide CopyrightTrademarks OpenSSL License Note Contents Contents AP-4000 Series User Guide System Status 4 Advanced Configuration Commands TroubleshootingMonitoring Recovery Procedures Command Line Interface CLI Ascii Character Chart C Specifications Statement of WarrantyTechnical Support Regulatory Compliance Products Covered in this User Guide Document ConventionsProduct Description Introduction AP-4000 Series User Guide Introduction to Wireless Networking Mesh Network Convergence Mesh Networking AP-4000M/4900M Only Mesh Startup Topology Example Step Mesh Network Configuration Guidelines for Roaming HTTP/HTTPS Interface Ieee 802.11 SpecificationsCommand Line Interface Management and Monitoring Capabilities SNMPv3 Secure Management Snmp Management SSH Secure Shell Management Overview AP-4000 Series Hardware Description External Antennas Antennas Installation and Initialization AP-4000 Series User Guide Active EthernetGHz Antenna LED Indicators on the AP-4000/4000M/4900M Top Panel LED Indicators General Prerequisites Prerequisites Mesh Prerequisites System Requirements Product Package Hardware Installation Required MaterialsCabling the AP-4000/4000M/4900M Mounting the AP-4000/4000M/4900M Installing the Security Cover Mounting the AP-4900M in a Vehicle Mounting the AP-4000/4000M/4900M to a Ceiling Opening the Antenna Compartment Installing External Antennas Attaching Antennas to the AP-4900M for 4.9 GHz Operation Installing the AP in a PlenumPage Using ScanTool InitializationScanTool Instructions Scan List Click LAN Settings LoggingSelect Tools Internet Options 11 Enter Network Password 12 System Status Screen Using the Setup WizardPage Download the Software Installing the Software Click Commands Update AP via Http Install Software with Http Interface Install Software with Tftp Server Click Commands Reboot Related Topics Install Updates from your Tftp Server using the CLI System Status Advanced Configuration Configure Main Screen Advanced Configuration AP-4000 Series User Guide Dynamic DNS Support SystemPage Network IP Configuration Dhcp Server DNS ClientAdvanced Advanced Configuration AP-4000 Series User Guide Network Start IP Address End IP AddressComment optional Dhcp Relay Agent Dhcp Server IP Address Table Dhcp Relay Agent Target IP Address Comment optional Link Integrity Sntp Simple Network Time Protocol Link Integrity Configuration Screen Sntp Configuration Screen Advanced Configuration AP-4000 Series User Guide Network Interfaces Operational Mode Advanced Configuration AP-4000 Series User Guide Interfaces Super Mode and Turbo ModeIeee 802.11d Support for Additional Regulatory Domains Configuring 802.11d Support TX Power Control/Transmit Power LevelConfiguring TX Power Control 10 Wireless Interface a Wireless-A 802.11a Radio and Wireless-B 802.11b/g Radio Advanced Configuration AP-4000 Series User Guide Interfaces Dynamic Frequency Selection/Radar Detection DFS/RD Wireless Service Status Affected CountriesRTS/CTS Medium Reservation Traps Generated During Wireless Service Shutdown and Resume Click on Configure Interfaces Wireless a or Wireless BChannel Blacklist Table 13 WDS Example Bridging WDS WDS Setup Procedure 15 Adding WDS Links Ethernet 16 Ethernet Sub-tab 17 Mesh Sub-tab AP-4000M/AP-4900M Mesh AP-4000M/AP-4900M Only 18 Mesh Sub-tab AP-4000 Mesh Software Kit Management Passwords IP Access Table ServicesSecure Management Advanced Configuration AP-4000 Series User Guide Management Https Access Secure Socket LayerAccessing the AP through the Https interface 19 Management Services Configuration Screen SSH Session Setup Configuring SSHSSH Clients Uploading Externally Generated Host Keys Click Commands Update AP via Http or via Tftp Radius Based Management Access Serial Configuration Settings Automatic Configuration AutoConfig Auto Configuration and the CLI Batch FileSet up Automatic Configuration for Static IP Set up Automatic Configuration for Dynamic IP 21 Automatic Configuration Screen 22 Dhcp Options Setting the Boot Server Host Name Hardware Configuration Reset Chrd Configuration Reset via Serial Port During Bootup Configuring Hardware Configuration ResetClick Configure Management Chrd Procedure to Reset Configuration via the Serial Interface Select the Filter Operation Type FilteringEthernet Protocol Static MAC Advanced Configuration AP-4000 Series User Guide Filtering Wireless MAC Address 0020A6124E38 Wired MAC Address 0040F41CDB6AWireless MAC Address 00022D5194E4 Wired MAC Address Click Add under the TCP/UDP Port Filter Table heading AdvancedTCP/UDP Port Number Click Edit under the TCP/UDP Port Filter Table heading Editing TCP/UDP Port Filters Groups Alarms Operational Trap Group Trap Name Description Severity Level Security Trap Group Trap Name Description Severity Level Flash Memory Trap Group Trap Name Description Severity Level Trap Name Description Severity Level Generic Trap Group Trap Name Description Severity Level Tftp Trap Group Trap Name Description Severity LevelImage Trap Group Trap Name Description Severity Level Sntp Trap Group Trap Name Description Severity Level RFC 1215-Trap Trap Name Description Severity Level Alarm Host Table Configuring Syslog Event Notifications SyslogEvent Priority Description Advanced Configuration AP-4000 Series User Guide Alarms Syslog MessagesSyslog Message Name Priority Severity Description Advanced Configuration AP-4000 Series User Guide Rogue Scan Continuous Scanning Mode Background Scanning ModeMulti-Band Scanning Click Configure Alarms Rogue Scan Rogue Scan Data CollectionRogue Scan 28 Rogue Scan Screen Spanning Tree Bridge Storm Threshold Advanced Configuration AP-4000 Series User Guide Bridge Configuring Interfaces for Packet Forwarding Intra BSSPacket Forwarding Enabling QoS and Adding QoS policies Wireless Multimedia Extensions WME/Quality of Service QoSClick Configure QoS Policy QoS Advanced Configuration AP-4000 Series User Guide QoS Enter the Priority Mapping Index101 Click Configure QoS Priority Mapping Priority Mapping102 Enhanced Distributed Channel Access Edca STA Edca Table and AP Edca Table103 104 Click Configure QoS Edca 105 Radius Servers per Authentication Mode and per Vlan Radius Profiles106 Configuring Radius Profiles Radius Servers Enforcing Vlan Access Control107 108 109 37 Add Radius Server Profile Session Length MAC Access Control Via Radius Authentication802.1x Authentication using Radius Radius Accounting Authentication Attributes Accounting Attributes111 112 SSID/VLAN/Security Vlan Overview113 114 Management Vlan Typical User Vlan ConfigurationsControl Access to the AP Click Configure SSID/VLAN/Security Mgmt Vlan Provide Access to a Wireless Host in the Same Workgroup Disable Vlan TaggingSecurity Profile Authentication Process Wi-Fi Protected Access WPA/802.11i WPA2117 118 Authentication Protocol Hierarchy Configuring Security Profiles Click Configure SSID/VLAN/Security Security ProfileVLANs and Security Profiles WPA Station Non Secure StationWEP Station 802.1x Station 121 802.11i-PSK Station 42 Security Profile Table Add Entries 122 MAC Access Wireless-A or Wireless-B123 124 Configuring an SSID/VLAN with Vlan Tagging Disabled 125 45 SSID/VLAN Edit Entries Screen Vlan Tagging Disabled Configuring SSID/VLANs with Vlan Tagging Enabled Click SSID/VLAN/Security Wireless-A or Wireless-B126 127 47 SSID/VLAN Edit Entries Screen Vlan Tagging Enabled 128 Broadcast Ssid and Closed System 129 Monitor Main Screen Monitoring AP-4000 Series User Guide Version Icmp Monitoring Tab IP/ARP Table Learn Table Monitoring Tab Learn Table Radius 134 135 Monitoring AP-4000 Series User Guide Interfaces 136 137 Station Statistics Monitoring AP-4000 Series User Guide Station Statistics Mesh Statistics 139 Introduction to File Transfer via Tftp or Http 140 Image Error Checking During File TransferTftp File Transfer Guidelines Http File Transfer Guidelines 141 Update APUpdate AP via Tftp Commands AP-4000 Series User Guide Update AP via Http Commands AP-4000 Series User Guide Update AP142 143 Commands AP-4000 Series User Guide Retrieve FileRetrieve File Retrieve File via Tftp 144 Retrieve File via Http Retrieve File via Http Command Screen Reboot ResetCommands AP-4000 Series User Guide Reboot Help Link 13 Help Link Configuration Screen 147 AP Unit Will Not Boot No LED Activity Troubleshooting ConceptsSymptoms and Solutions Connectivity Issues Basic Software Setup and Configuration Problems Client Connection Problems Active Ethernet AE Vlan Operation Issues Recovery Procedures Reset to Factory Default ProcedureForced Reload Procedure 153 Download a New Image Using ScanToolDownload Procedure Preparing to Download the AP Image 154 Download a New Image Using the Bootloader CLI Attaching the Serial Port Cable Setting IP Address using Serial PortInitializing the IP Address using CLI Hardware and Software Requirements Radius Authentication Server Related Applications156 157 Tftp Server Important Terminology General NotesPrerequisite Skills and Knowledge Notation Conventions Key Combination Operation CLI Error MessagesError Message Description Navigation and Special Keys 160 Command Line Interface CLI VariationsBootloader CLI Command Line Interface CLI AP-4000 Series User Guide CLI Command Types Operational CLI CommandsExample 1. Display Command list Example 2. Display specific Commands Example 3. Display parameters for set and showExample 3a. Display every parameter that can be changed Download Example 3b. Display parameters based on letter sequenceExample 4. Display Prompts for Successive Parameters Done, exit, quit 164 HelpHistory Passwd 165 Parameter Control CommandsShow CLI Command Search Examples Set CLI CommandConfiguring Objects that Require Reboot Set and show Command Examples Example 3 Modify a table entry or row Example 1 Set the Access Point IP Address ParameterExample 4 Enable, Disable, or Delete a table entry or row Example 2 Create a table entry or row Example 5 Show the Group Parameters Example 6 Show Individual and Table Parameters168 169 Using Tables and StringsUsing Strings Working with Tables Log into the AP using Telnet Configuring the AP using CLI commandsSet Basic Configuration Parameters using CLI Commands Log into the AP using HyperTerminal 171 Change PasswordsSet Network Names for the Wireless Interface Set System Name, Location and Contact Information 172 Country Code 173 Configure SSIDs Network Names, VLANs, and Profiles 174 Download an AP Configuration File from your Tftp ServerBackup your AP Configuration File Set up Auto Configuration Other Network Settings Configure the AP as a Dhcp ServerConfigure the DNS Client Autochannel Select ACS Operational Mode Enable/Disable Turbo Mode 802.11a/g only Enable/Disable Closed SystemShutdown/Resume Wireless Service Enable/Disable Super Mode 802.11a/g only Edit Management IP Access Table Configure Management PortsSet the Distance Between APs Set Communication Ports Configure Secure Socket Layer HttpsSet Telnet Session Timeouts Configure Serial Port Interface Add an Entry to the MAC Access Control Table Create/Enable WDSEnable/Disable WDS Setup MAC Address Access Control Configure Radius Authentication servers Set Radius Parameters181 182 Set Hardware Configuration Reset Parameters Configure a Security Profile with WEP Security Mode Enable Vlan ManagementDisable Vlan Management Configure a Security Profile with Non Secure Security Mode Parameter Tables Configure a Security Profile with 802.11i Security ModeConfigure a Security Profile with 802.11i-PSK Security Mode CLI Monitoring Parameters 185 Serial Port Parameters Serial Port setup 186 187 Name Type Value Access CLI ParameterSet sysresettodefaults System Parameters 188 DNS Client for Radius Name ResolutionDhcp Server Parameters Name Type Value Access CLI Parameter Network Parameters 189 Dhcp Server table for IP poolsDhcp Relay Group Dhcp Relay Server Table Sntp Parameters Name Type Value Access CLI Parameter Link Integrity IP Target Table190 191 Wireless Interface ParametersInterface Parameters Common Parameters to 802.11a/b/g 192 802.11a Only Parameters 802.11b Only Parameters 802.11b/g Only Parameters193 Mode For 802.11g-only modeFor 802.11b/g mode For 802.11b-only 195 Wireless Distribution System WDS ParametersWireless Interface SSID/VLAN/Profile Parameters Channel Blacklist Parameters 196 Wireless Distribution System WDS Security Table Parameters Snmp Parameters Name Type Value Access CLI Parameter Management Parameters197 198 Http Parameters Name Type Value Access CLI Parameter Telnet Parameters Name Type Value Access CLI Parameter199 200 Serial Port Parameters Name Type Value Access CLI ParameterRadius Based Management Access Parameters SSH Parameters IP Access Table Parameters Tftp Server Parameters201 Filtering Parameters Ethernet Filtering Table202 203 Proxy ARP Parameters Name Type Value Access CLI ParameterTCP/UDP Port Filtering TCP/UDP Port Filtering Table Alarms Parameters Snmp Table Host Table Parameters204 Syslog Parameters Syslog Host Table205 Bridge Parameters Spanning Tree Priority and Path Cost Table206 207 Storm Threshold TableIntra BSS Subscriber Blocking Packet Forwarding Parameters 208 Radius Server Configuration ParametersRadius Parameters General Radius Parameters Security Parameters MAC Access Control Table 210 Security Profile Table 211 Iapp Parameters Name Type Value Access CLI ParameterVLAN/SSID Parameters Other Parameters 212 Enabling QoS Name Type Value Access CLI ParameterConfiguring QoS Policies Specifying the Mapping between 802.1p and 802.1D Priorities 213 QoS Enhanced Distributed Channel Access Edca Parameters Sample CLI Batch File Auto Configuration and the CLI Batch FileCLI Batch File CLI Batch File Format and Syntax Reboot Behavior CLI Batch File Error Log215 Charact Equival Ent 216 Hex Number of Stations per BSS Software FeaturesFeature Supported by AP-4000 Series Radius Based Management Access 217 Security Functions Medium Access Control MAC FunctionsSpecifications AP-4000 Series User Guide Software Features Advanced Bridging Functions Specifications AP-4000 Series User Guide Network Functions219 Hardware Specifications Available Channels AP-4000/4000M Channels221 222 AP-4900M Channels 4.9 GHz Public Safety ModeAP-4900M Channels AP-4900M Channels a/b/g Modes 223 Software and Documentation Downloads Knowledgebase 224 Online Support International 225 Telephone Support Support Procedures Warranty CoverageRepair or Replacement Limitations of Warranty Other Adapter Cards Ask a Question or Open an IssueOther Information Search Knowledgebase 228 Product Model Numbers 229 Regulatory Compliance AP-4000 Series User Guide 230 Safety Information USA, Canada, & European Union 231 Federal Communications Commission FCC AP-4000/4000M 232 Modifications 233 Industry Canada IC AP-4000/4000M only 234 European Union AP-4000/4000M only 235 Regulatory Compliance Certifications Summary AP-4000/4000MRegulatory Compliance Certifications Summary AP-4900M Country Certification/Reference No