Enter Network Password | Proxim AP-4000 guide

Installation and Initialization	AP-4000 Series User Guide
Initialization

– Click OK twice to save your changes and return to Internet Explorer.

3.Enter the Access Point’s IP address in the browser’s Address field and press Enter or Go.

This is either the dynamic IP address assigned by a network DHCP server or the static IP address you manually configured. See Using ScanTool for information on how to determine the unit’s IP address and manually configure a new IP address, if necessary.

NOTE: Mesh APs must be configured with static IP addresses. The Enter Network Password screen appears.

Figure 2-11 Enter Network Password

4.Enter the HTTP password in the Password field. Leave the User Name field blank. For new units, the default HTTP password is public.

If you are logging on for the first time the Setup Wizard will launch automatically.

NOTE: To prevent the Setup Wizard from launching upon log in, click on Management > Services and choose Disable from the Setup Wizard drop down menu.

5.Follow the steps below to configure the AP using the Setup Wizard (see Using the Setup Wizard), or click Exit to configure the system manually. Upon clicking Exit, the System Status screen will appear.

34

Image 34

Proxim AP-4000 manual Enter Network Password

Contents

ORiNOCO AP-4000 Series Access Points User Guide OpenSSL License Note CopyrightTrademarks AP-4000 Series User Guide Contents System Status 4 Advanced Configuration Contents AP-4000 Series User Guide Troubleshooting CommandsMonitoring Command Line Interface CLI Recovery Procedures Statement of Warranty Ascii Character Chart C SpecificationsTechnical Support Regulatory Compliance Document Conventions Products Covered in this User GuideProduct Description Introduction to Wireless Networking Introduction AP-4000 Series User Guide Mesh Networking AP-4000M/4900M Only Mesh Network Convergence Mesh Startup Topology Example Step Mesh Network Configuration Guidelines for Roaming Management and Monitoring Capabilities Ieee 802.11 SpecificationsCommand Line Interface HTTP/HTTPS Interface Snmp Management SNMPv3 Secure Management SSH Secure Shell Management AP-4000 Series Hardware Description Overview Antennas External Antennas Active Ethernet Installation and Initialization AP-4000 Series User GuideGHz Antenna LED Indicators LED Indicators on the AP-4000/4000M/4900M Top Panel Prerequisites General Prerequisites Mesh Prerequisites Product Package System Requirements Required Materials Hardware InstallationCabling the AP-4000/4000M/4900M Installing the Security Cover Mounting the AP-4000/4000M/4900M Mounting the AP-4000/4000M/4900M to a Ceiling Mounting the AP-4900M in a Vehicle Installing External Antennas Opening the Antenna Compartment Installing the AP in a Plenum Attaching Antennas to the AP-4900M for 4.9 GHz OperationPage Initialization Using ScanToolScanTool Instructions Scan List Logging Click LAN SettingsSelect Tools Internet Options 11 Enter Network Password Using the Setup Wizard 12 System Status ScreenPage Installing the Software Download the Software Install Software with Http Interface Click Commands Update AP via Http Click Commands Reboot Install Software with Tftp Server Install Updates from your Tftp Server using the CLI Related Topics System Status Advanced Configuration Advanced Configuration AP-4000 Series User Guide Configure Main Screen System Dynamic DNS SupportPage IP Configuration Network DNS Client Dhcp ServerAdvanced Start IP Address End IP Address Advanced Configuration AP-4000 Series User Guide NetworkComment optional Dhcp Relay Agent Dhcp Relay Agent Dhcp Server IP Address Table Link Integrity Target IP Address Comment optional Link Integrity Configuration Screen Sntp Simple Network Time Protocol Sntp Configuration Screen Advanced Configuration AP-4000 Series User Guide Network Operational Mode Interfaces Super Mode and Turbo Mode Advanced Configuration AP-4000 Series User Guide InterfacesIeee 802.11d Support for Additional Regulatory Domains TX Power Control/Transmit Power Level Configuring 802.11d SupportConfiguring TX Power Control Wireless-A 802.11a Radio and Wireless-B 802.11b/g Radio 10 Wireless Interface a Advanced Configuration AP-4000 Series User Guide Interfaces Dynamic Frequency Selection/Radar Detection DFS/RD Affected Countries Wireless Service StatusRTS/CTS Medium Reservation Click on Configure Interfaces Wireless a or Wireless B Traps Generated During Wireless Service Shutdown and ResumeChannel Blacklist Table 13 WDS Example WDS Setup Procedure Bridging WDS Ethernet 15 Adding WDS Links 16 Ethernet Sub-tab Mesh AP-4000M/AP-4900M Only 17 Mesh Sub-tab AP-4000M/AP-4900M Mesh Software Kit 18 Mesh Sub-tab AP-4000 Passwords Management Services IP Access TableSecure Management Https Access Secure Socket Layer Advanced Configuration AP-4000 Series User Guide ManagementAccessing the AP through the Https interface 19 Management Services Configuration Screen Configuring SSH SSH Session SetupSSH Clients Click Commands Update AP via Http or via Tftp Uploading Externally Generated Host Keys Serial Configuration Settings Radius Based Management Access Auto Configuration and the CLI Batch File Automatic Configuration AutoConfigSet up Automatic Configuration for Static IP 21 Automatic Configuration Screen Set up Automatic Configuration for Dynamic IP Hardware Configuration Reset Chrd 22 Dhcp Options Setting the Boot Server Host Name Configuring Hardware Configuration Reset Configuration Reset via Serial Port During BootupClick Configure Management Chrd Procedure to Reset Configuration via the Serial Interface Static MAC FilteringEthernet Protocol Select the Filter Operation Type Advanced Configuration AP-4000 Series User Guide Filtering Wired MAC Address Wired MAC Address 0040F41CDB6AWireless MAC Address 00022D5194E4 Wireless MAC Address 0020A6124E38 Number AdvancedTCP/UDP Port Click Add under the TCP/UDP Port Filter Table heading Editing TCP/UDP Port Filters Click Edit under the TCP/UDP Port Filter Table heading Alarms Groups Security Trap Group Trap Name Description Severity Level Operational Trap Group Trap Name Description Severity Level Trap Name Description Severity Level Flash Memory Trap Group Trap Name Description Severity Level Sntp Trap Group Trap Name Description Severity Level Tftp Trap Group Trap Name Description Severity LevelImage Trap Group Trap Name Description Severity Level Generic Trap Group Trap Name Description Severity Level Alarm Host Table RFC 1215-Trap Trap Name Description Severity Level Syslog Configuring Syslog Event NotificationsEvent Priority Description Syslog Messages Advanced Configuration AP-4000 Series User Guide AlarmsSyslog Message Name Priority Severity Description Advanced Configuration AP-4000 Series User Guide Rogue Scan Background Scanning Mode Continuous Scanning ModeMulti-Band Scanning Rogue Scan Data Collection Click Configure Alarms Rogue ScanRogue Scan 28 Rogue Scan Screen Bridge Spanning Tree Advanced Configuration AP-4000 Series User Guide Bridge Storm Threshold Intra BSS Configuring Interfaces for Packet ForwardingPacket Forwarding QoS Wireless Multimedia Extensions WME/Quality of Service QoSClick Configure QoS Policy Enabling QoS and Adding QoS policies Enter the Priority Mapping Index Advanced Configuration AP-4000 Series User Guide QoS101 Priority Mapping Click Configure QoS Priority Mapping102 STA Edca Table and AP Edca Table Enhanced Distributed Channel Access Edca103 Click Configure QoS Edca 104 105 Radius Profiles Radius Servers per Authentication Mode and per Vlan106 Radius Servers Enforcing Vlan Access Control Configuring Radius Profiles107 108 37 Add Radius Server Profile 109 Radius Accounting MAC Access Control Via Radius Authentication802.1x Authentication using Radius Session Length Accounting Attributes Authentication Attributes111 112 Vlan Overview SSID/VLAN/Security113 114 Click Configure SSID/VLAN/Security Mgmt Vlan Typical User Vlan ConfigurationsControl Access to the AP Management Vlan Disable Vlan Tagging Provide Access to a Wireless Host in the Same WorkgroupSecurity Profile Wi-Fi Protected Access WPA/802.11i WPA2 Authentication Process117 Authentication Protocol Hierarchy 118 Click Configure SSID/VLAN/Security Security Profile Configuring Security ProfilesVLANs and Security Profiles 802.1x Station Non Secure StationWEP Station WPA Station 802.11i-PSK Station 121 42 Security Profile Table Add Entries 122 Wireless-A or Wireless-B MAC Access123 Configuring an SSID/VLAN with Vlan Tagging Disabled 124 45 SSID/VLAN Edit Entries Screen Vlan Tagging Disabled 125 Click SSID/VLAN/Security Wireless-A or Wireless-B Configuring SSID/VLANs with Vlan Tagging Enabled126 47 SSID/VLAN Edit Entries Screen Vlan Tagging Enabled 127 Broadcast Ssid and Closed System 128 Monitor Main Screen 129 Version Monitoring AP-4000 Series User Guide IP/ARP Table Icmp Monitoring Tab Learn Table Learn Table Monitoring Tab Radius 134 Monitoring AP-4000 Series User Guide Interfaces 135 136 Station Statistics 137 Mesh Statistics Monitoring AP-4000 Series User Guide Station Statistics Introduction to File Transfer via Tftp or Http 139 Http File Transfer Guidelines Image Error Checking During File TransferTftp File Transfer Guidelines 140 Commands AP-4000 Series User Guide Update APUpdate AP via Tftp 141 Commands AP-4000 Series User Guide Update AP Update AP via Http142 Retrieve File via Tftp Commands AP-4000 Series User Guide Retrieve FileRetrieve File 143 Retrieve File via Http 144 Retrieve File via Http Command Screen Reset RebootCommands AP-4000 Series User Guide Reboot 13 Help Link Configuration Screen 147 Help Link Connectivity Issues Troubleshooting ConceptsSymptoms and Solutions AP Unit Will Not Boot No LED Activity Basic Software Setup and Configuration Problems Client Connection Problems Vlan Operation Issues Active Ethernet AE Reset to Factory Default Procedure Recovery ProceduresForced Reload Procedure Preparing to Download the AP Image Download a New Image Using ScanToolDownload Procedure 153 Download a New Image Using the Bootloader CLI 154 Hardware and Software Requirements Setting IP Address using Serial PortInitializing the IP Address using CLI Attaching the Serial Port Cable Related Applications Radius Authentication Server156 Tftp Server 157 Notation Conventions General NotesPrerequisite Skills and Knowledge Important Terminology Navigation and Special Keys CLI Error MessagesError Message Description Key Combination Operation Command Line Interface CLI AP-4000 Series User Guide Command Line Interface CLI VariationsBootloader CLI 160 Operational CLI Commands CLI Command TypesExample 1. Display Command list Example 3. Display parameters for set and show Example 2. Display specific CommandsExample 3a. Display every parameter that can be changed Done, exit, quit Example 3b. Display parameters based on letter sequenceExample 4. Display Prompts for Successive Parameters Download Passwd HelpHistory 164 Search Parameter Control CommandsShow CLI Command 165 Set and show Command Examples Set CLI CommandConfiguring Objects that Require Reboot Examples Example 2 Create a table entry or row Example 1 Set the Access Point IP Address ParameterExample 4 Enable, Disable, or Delete a table entry or row Example 3 Modify a table entry or row Example 6 Show Individual and Table Parameters Example 5 Show the Group Parameters168 Working with Tables Using Tables and StringsUsing Strings 169 Log into the AP using HyperTerminal Configuring the AP using CLI commandsSet Basic Configuration Parameters using CLI Commands Log into the AP using Telnet Set System Name, Location and Contact Information Change PasswordsSet Network Names for the Wireless Interface 171 Country Code 172 Configure SSIDs Network Names, VLANs, and Profiles 173 Set up Auto Configuration Download an AP Configuration File from your Tftp ServerBackup your AP Configuration File 174 Configure the AP as a Dhcp Server Other Network SettingsConfigure the DNS Client Operational Mode Autochannel Select ACS Enable/Disable Super Mode 802.11a/g only Enable/Disable Closed SystemShutdown/Resume Wireless Service Enable/Disable Turbo Mode 802.11a/g only Configure Management Ports Edit Management IP Access TableSet the Distance Between APs Configure Serial Port Interface Configure Secure Socket Layer HttpsSet Telnet Session Timeouts Set Communication Ports Setup MAC Address Access Control Create/Enable WDSEnable/Disable WDS Add an Entry to the MAC Access Control Table Set Radius Parameters Configure Radius Authentication servers181 Set Hardware Configuration Reset Parameters 182 Configure a Security Profile with Non Secure Security Mode Enable Vlan ManagementDisable Vlan Management Configure a Security Profile with WEP Security Mode CLI Monitoring Parameters Configure a Security Profile with 802.11i Security ModeConfigure a Security Profile with 802.11i-PSK Security Mode Parameter Tables Serial Port Parameters Serial Port setup 185 186 System Parameters Name Type Value Access CLI ParameterSet sysresettodefaults 187 Network Parameters DNS Client for Radius Name ResolutionDhcp Server Parameters Name Type Value Access CLI Parameter 188 Dhcp Relay Server Table Dhcp Server table for IP poolsDhcp Relay Group 189 Link Integrity IP Target Table Sntp Parameters Name Type Value Access CLI Parameter190 Common Parameters to 802.11a/b/g Wireless Interface ParametersInterface Parameters 191 802.11a Only Parameters 192 802.11b/g Only Parameters 802.11b Only Parameters193 For 802.11b-only For 802.11g-only modeFor 802.11b/g mode Mode Channel Blacklist Parameters Wireless Distribution System WDS ParametersWireless Interface SSID/VLAN/Profile Parameters 195 Wireless Distribution System WDS Security Table Parameters 196 Management Parameters Snmp Parameters Name Type Value Access CLI Parameter197 198 Telnet Parameters Name Type Value Access CLI Parameter Http Parameters Name Type Value Access CLI Parameter199 SSH Parameters Serial Port Parameters Name Type Value Access CLI ParameterRadius Based Management Access Parameters 200 Tftp Server Parameters IP Access Table Parameters201 Ethernet Filtering Table Filtering Parameters202 TCP/UDP Port Filtering Table Proxy ARP Parameters Name Type Value Access CLI ParameterTCP/UDP Port Filtering 203 Snmp Table Host Table Parameters Alarms Parameters204 Syslog Host Table Syslog Parameters205 Spanning Tree Priority and Path Cost Table Bridge Parameters206 Packet Forwarding Parameters Storm Threshold TableIntra BSS Subscriber Blocking 207 General Radius Parameters Radius Server Configuration ParametersRadius Parameters 208 MAC Access Control Table Security Parameters Security Profile Table 210 Other Parameters Iapp Parameters Name Type Value Access CLI ParameterVLAN/SSID Parameters 211 Specifying the Mapping between 802.1p and 802.1D Priorities Enabling QoS Name Type Value Access CLI ParameterConfiguring QoS Policies 212 QoS Enhanced Distributed Channel Access Edca Parameters 213 CLI Batch File Format and Syntax Auto Configuration and the CLI Batch FileCLI Batch File Sample CLI Batch File CLI Batch File Error Log Reboot Behavior215 Hex Charact Equival Ent 216 Radius Based Management Access 217 Software FeaturesFeature Supported by AP-4000 Series Number of Stations per BSS Advanced Bridging Functions Medium Access Control MAC FunctionsSpecifications AP-4000 Series User Guide Software Features Security Functions Network Functions Specifications AP-4000 Series User Guide219 Hardware Specifications AP-4000/4000M Channels Available Channels221 AP-4900M Channels a/b/g Modes AP-4900M Channels 4.9 GHz Public Safety ModeAP-4900M Channels 222 223 Online Support Software and Documentation Downloads Knowledgebase 224 Telephone Support International 225 Limitations of Warranty Warranty CoverageRepair or Replacement Support Procedures Search Knowledgebase Ask a Question or Open an IssueOther Information Other Adapter Cards Product Model Numbers 228 Regulatory Compliance AP-4000 Series User Guide 229 Safety Information USA, Canada, & European Union 230 Federal Communications Commission FCC AP-4000/4000M 231 Modifications 232 Industry Canada IC AP-4000/4000M only 233 European Union AP-4000/4000M only 234 Country Certification/Reference No Regulatory Compliance Certifications Summary AP-4000/4000MRegulatory Compliance Certifications Summary AP-4900M 235