Manuals / Q-Logic / Computer Equipment / Switch

Q-Logic 5200, 5202 manual Legacy Port Address Format, Timeout Values

Models: 5200 5202

1 268

Download 268 pages 9.43 Kb

Page 110

4 – Managing Switches	0
4 – Managing Switches
Configuring a Switch

4.7.2.8

Legacy Port Address Format

Legacy Address Format should be enabled only to permit interoperation with certain older non-FC-SW-2 switches. Enabling this setting under other circumstances will disable zoning that is defined by domain ID and port number. This setting is available only when the Interop Mode setting is disabled. Contact your authorized maintenance provider for assistance in using this feature. Refer to the QLogic Switch Interoperability Guide on the QLogic Web site for a complete discussion of configuring for operation with non-Qlogic switches.

Note: The Legacy Address Format setting must be the same on all switches in the fabric, otherwise the inter-switch links will not connect.

4.7.2.9

Timeout Values

The switch timeout values determine the timeout values for all ports on the switch. Table 4-5describes the switch timeout parameters. The timeout values must be the same for all switches in the fabric.

Note: Mismatched timeout values will disrupt the fabric. These should not be changed unless absolutely necessary. Therefore, the switch must be offline to change these values. Use the Switch Properties dialog to take the switch offline.

	Table 4-5. Timeout Values

Parameter	Description

R_A_TOV	Resource Allocation Timeout: Represents the maximum time a frame
	could be delayed in the Fabric and still be delivered. The default is
	10000 milliseconds.
E_D_TOV	Error Detect Timeout: Represents the maximum round trip time that
	an operation between two N_Ports could require. The default is 2000
	milliseconds.

4-22	59056-02 A

Image 110

Q-Logic 5200, 5202 manual Legacy Port Address Format, Timeout Values

Contents

SANbox 5200 Series Switch Management User’s Guide SANbox 5200 Series Switch Management User’s Guide Document Revision History Table of Contents Section Managing Fabrics SANbox 5200 Series Switch Management Section Managing Switches Section Managing Ports 4.1 Snmp Configuration 4.2 Snmp Trap ConfigurationChanging the Default Performance View File Encryption Key 3.3 NTP Client Appendix a Command Line Interface 7.3 102 Shutdown CommandGlossary Index 104Page Tables 105 SANbox 5200 Series Switch Management User’s Guide 59056-02 a Intended Audience Related Materials Jdom License Training Technical SupportAvailability Contact Information Introduction Technical Support 59056-02 a Using SANsurfer Switch Manager Installing the Management Application For a Linux workstation SANsurfer Switch ManagerFor a Windows workstation For a Solaris workstation SMS Installation for Windows SANsurfer Management Suite Chglax.bat SMS Installation for Linux SMS Installation for Solaris Locate and execute the file sbmoversms.sh Install the new SANsurfer Switch Manager packageChange directories to the package location Starting SANsurfer Switch Manager ‰ For Linux or Solaris enter the SANsurfer command Initial Startup Dialog Exiting SANsurfer Switch Manager SANsurfer Switch Manager Window Save Default Fabric View File Dialog Uninstalling SANsurfer Switch Manager SMS Uninstall Standalone Uninstall Changing the Encryption Key for the Default Fabric View File Setting SANsurfer Switch Manager Preferences Saving and Opening Fabric View Files Preferences Dialog SANsurfer Switch Manager Using Online Help Viewing Software Version and Copyright Information Faceplate Display SANsurfer Switch Manager User InterfaceTopology Display Menu Bars Topology Display Menu Faceplate Display Menu Faceplate Display Menu Topology Display Shortcut Keys Topology Display Menu Shortcut Keys Faceplate Display Shortcut Keys Faceplate Display Shortcut Keys Alt+S, L SwitchLoad Firmware Tool Bar Tool Bar Buttons Fabric Tree Fabric Tree Data Window and Tabs Working Status IndicatorGraphic Window Using the Topology Display Switch and Link Status Arranging Switches in the Display Working with Switches and LinksSelecting Switches and Links Opening the Faceplate Display and Topology Popup Menus Topology Data Windows Using the Faceplate Display 11. Faceplate Display Selecting Ports Port Views and StatusWorking with Ports Opening the Faceplate Popup Menu Faceplate Data WindowsPage Fabric Security User Account Security Click the In-band Management Enable button Fabric ServicesEnabling Snmp Configuration Enabling In-band Management Viewing and Comparing Version Snapshots Fabric TrackerSaving a Version Snapshot Exporting Version Snapshots to a File Managing the Fabric Database Adding a Fabric Add a New Fabric Dialog Saving a Fabric View File Removing a FabricOpening a Fabric View File Rediscovering a Fabric Deleting Switches and Links Adding a New Switch to a Fabric Replacing a Failed Switch Displaying Fabric Information Topology Display Switch and Status Icons Fabric Status Displaying the Event Browser Events Browser Severity Levels Description Icon Filtering the Event Browser Filter Events Dialog Sorting the Event Browser Saving the Event Browser to a File Devices Data Window Devices Data Window Entries Active Zone Set Data Window Active Zone Set Data Window Displaying Detailed Device Information Link Data WindowWorking with Device Information and Nicknames Creating a Nickname Exporting Device Information to a FileManaging Device Port Nicknames Exporting Nicknames to a File Editing a NicknameDeleting a Nickname Zoning Concepts Importing a Nicknames FileZoning a Fabric Zones Soft Zones Zone Sets Access Control List Hard ZonesAliases Zoning Database Managing the zoning database consists of the following Using the Zoning WizardManaging the Zoning Database Editing the Zoning Database Edit Zoning Dialog Edit Zoning Dialog Tool Bar Buttons and Icons Create Alias button create another name for a set of objects Configuring the Zoning Database Interop Auto Save Restoring the Zoning Database from a File Default VisibilitySaving the Zoning Database to a File Restoring the Default Zoning Database Removing All Zoning Definitions Managing Zone Sets Creating a Zone Set Removing a Zone from a Zone Set or from All Zone Sets Activating and Deactivating a Zone SetCopying a Zone to a Zone Set Managing zones involves the following Removing a Zone SetManaging Zones Creating a Zone in a Zone Set Adding Zone Members Removing a Zone from a Zone Set Renaming a Zone or a Zone SetRemoving a Zone Member Removing a Zone from All Zone Sets Creating an Alias Changing Zone TypesManaging Aliases Adding a Member to an Alias Removing an Alias from All Zones Merging Fabrics and Zoning Zone Merge Failure Zone Merge Failure Recovery Managing Switches Managing User Accounts Factory User Accounts User Account Administration Dialog Add Account Creating User Accounts User Account Administration Dialog Remove Account Removing a User Account Changing a User Account Password User Account Administration Dialog Change Password User Account Administration Dialog Modify Account Modifying a User Account Displaying Switch Information Faceplate Display Switch Information Switch Data Window Switch Data Window Entries Ratov Displaying Detailed Device Information on page 3-17for Port Statistics Data Window Port Information Data Window Configured Zonesets Data Windows Configured Zonesets Data Window Configuring Port Threshold Alarms Port Threshold Alarm Configuration Dialog Count Paging a SwitchEvent Sample Window Setting the Date/Time and Enabling NTP Client Resetting a Switch Switch Resets Type Description Switch Properties Configuring a SwitchUsing the Configuration Wizard Symbolic Name Switch Administrative States Switch Administrative States Domain ID and Domain ID Lock Fabric Device Management Interface In-band Management Interop Mode for ZoningBroadcast Support Legacy Port Address Format Timeout ValuesTimeout Values Network Properties 10. Network Properties Dialog IP Configuration IP Configuration Parameters Remote Logging NTP Client Snmp Properties 11. Snmp Properties Dialog Snmp Configuration Snmp Configuration Parameters Snmp Trap Configuration Snmp Trap Configuration Parameters Archiving a Switch Restoring a Switch 12. Restore Dialogs Full and Selective Restoring the Factory Default Configuration Factory Default Configuration Settings Factory Default Configuration Settings Downloading a Support File Upgrading the Switch Using License Keys 13. Features License Key Dialog Installing Firmware Displaying Hardware Status 15. Hardware Status LEDs Managing Ports Displaying Port Information Port Types Monitoring Port StatusDisplaying Port Types Port Operational States Displaying Port Operational StatesDisplaying Port Speeds Port Speeds Displaying Transceiver Media Status Port Transceiver Media View Port Statistics Data Window Entries LIP ALPD,ALPS Port Statistics Data Window Entries Port Information Data Window Entries Port Information Data Window Entries Configuring Ports Port Properties Dialog Changing Port Administrative States Port Administrative States Changing Port Speeds Changing Port Types Stream Guard Scan Device Changing Port Symbolic Name Using the Extended Credits Wizard Resetting a Port Designate Donor Ports Testing Ports Port Loopback Test Dialog Managing Ports Graphing Port Performance Fabric View Graphs Starting SANsurfer Performance Viewer Exiting SANsurfer Performance Viewer Save Default Performance View File Dialog Saving and Opening Performance View Files Changing the Default Performance View File Encryption Key Setting SANsurfer Performance Viewer Preferences Setting the Polling Frequency Displaying Graphs Arranging Graphs in the Display Customizing Graphs Managing Ports Graphing Port Performance Saving Graph Statistics to a File Rescaling a Selected GraphPrinting Graphs Managing Ports Graphing Port Performance 59056-02 a Command Line Interface Logging On to a Switch User Accounts Working with Switch Configurations Modifying a Configuration Backing up and Restoring Switch Configurations Ftp ipaddress Date, configswitch16910112003, for example Command keyword keyword value CommandsCommand syntax is as follows Table A-1. Command-Line Completion Table A-2. Commands Listed by Authority Level Admin Session Commands Syntax Admin CommandAuthority Keywords Alias Command Syntax alias Rename aliasold aliasnew Members aliasRemove alias memberlist Keywords activate configname Config CommandSyntax config Edit configname Restore command RestoreManager Archive function are not compatible with the Config Save configname # ftp symbolicname or ipaddress Download the file to the workstation Following is an example of the Create Support command Create Support CommandAdmin session Create support You have transferred 43430 bytes in 1 files Keywords MMDDhhmmCCYY Date CommandSyntax date Keywords add licensekey Feature CommandSyntax feature Log Syntax firmware install Firmware Install CommandAuthority Admin Hardreset Command Syntax Syntax help command keyword Help CommandKeywords command Authority None History Command Authority None Syntax history Hotreset Command Hotreset Image Command Ftp Ftp switchname Wait for the unpack to complete Reinitializes the specified loop port Lip CommandFollowing is an example of the Lip command Lip portnumber Passwd Command Syntax passwd accountname Keywords accountname Keywords ipaddress Ping CommandSyntax ping ipaddress Syntax Examples Ps CommandFollowing is an example of the Ps command Displays current system process information Syntax quit, exit, or logout Quit CommandCloses the Telnet session Reset Command Config configname Zoning Table A-3. Switch Configuration DefaultsSystem Table A-4. Port Configuration Defaults Table A-5. Port Threshold Alarm Configuration Defaults Table A-6. Zoning Configuration Defaults Table A-7. Snmp Configuration Defaults Table A-8. System Configuration Defaults Set Command Syntax set Port option Setup optionSwitch state Table A-9. Set Config Port Parameters Set Config CommandSet config Port portnumber Command Line Interface Set Config Command Table A-9. Set Config Port Parameters Table A-10. Set Config Switch Parameters Number of milliseconds the switch Table A-10. Set Config Switch Parameters Table A-11. Set Config Threshold Parameters Threshold Table A-12. Set Config Zoning Parameters Arbff Following is an example of the Set Config Switch command Following is an example of the Set Config Threshold command To discard this configuration use the config cancel command Following is an example of the Set Config Zoning command Attributes Archive Set Log CommandSet log Clear Display filter Level filter Start Port portlistSave Stop Set Port Command Down Port from accepting a device loginDisables the port by removing power from the port lasers Table A-13. Snmp Configuration Settings Set Setup CommandSet setup Snmp System Table A-14. System Configuration Settings Table A-14. System Configuration Settings Setup snmp Following is an example of the Set Setup System command SANbox Manager admin # set setup system Keywords about Show CommandAlarm option Broadcast Fdmi portwwn Log option Perf option Ns optionPagebreak Table A-15. Show Port Parameters Lipalpdalps Post log Steering domainid Table A-16. Switch Operational Parameters Support Users TopologyDisplays all connected devices Version Following is an example of the Show Domains command Following is an example of the Show Fabric command Following is an example of the Show Fdmi command Following is an example of the Show Fdmi WWN command Following is an example of the Show NS portID command Following is an example of the Show NS local domain commandFollowing is an example of the Show NS domainID command Following is an example of the Show Interface command Collisions0 txqueuelen100 Following is an example of the Show Port command PL-XPL-VC-SG3-22 Following is an example of the Show Switch command Following is an example of the Show Topology command Command Line Interface Show Command Following is an example of the Show Version command Show Config Command Show config Following is an example of the Show Config Switch command Following is an example of the Show Config Threshold command Following is an example of the Show Config Zoning command Number of events Show Log CommandShow log Component Options SettingsLevel Port Following is an example of the Show Log command Following is an example of the Show Log Level commandFollowing is an example of the Show Log Options command Show Perf Command Errors portnumber Following is an example of the Show Perf Byte command Mfg Show Setup CommandShow setup Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Shutdown Shutdown CommandPower from the switch Port portnumber testtype Test CommandTest Status Admin start Command Line Interface Test Command Authority None Syntax uptime Uptime CommandExamples The following is an example of the Uptime command User Command Following is an example of the User Add command Following is an example of the User Edit command Following is an example of the User Delete command Following is an example of the User List command Whoami Whoami CommandFollowing is an example of the Whoami command Zone Command Syntax zone Rename zoneold zonenew Members zoneRemove zone memberlist Type zone zonetype Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zoneset Zones zoneset Remove zoneset zonelistRename zonesetold zonesetnew History Zoning CommandOpens a Zoning Edit session Limits Table A-17. Zoning Database Limits Following is an example of the Zoning Limits command E1JBOD1 E2JBOD2 Following is an example of the Zoning List command 108 59056-02 a Alarm Access Control List ZoneAdministrative State BootP Default Visibility Class 3 ServiceConfigured Zone Sets Fabric Management Switch Maintenance Button Input Power LEDInter-Switch Link Maintenance Mode Soft Zone Zoning DatabaseSmall Form-Factor Pluggable Target Index Index-2 59056-02 a 59056-02 a Index-3 Index-4 59056-02 a 59056-02 a Index-5 Index-6 59056-02 a