Table A-14. System Configuration Settings | Q-Logic 5200, 5202

A – Command Line Interface			0
A – Command Line Interface
Set Setup Command


	Table A-14. System Configuration Settings (Continued)

	Entry		Description

	Eth0NetworkMask		Ethernet subnet mask address.
	Eth0GatewayAddress		Ethernet IP address gateway.
	AdminTimeout		Amount of time in minutes the switch waits before
			terminating an idle Admin session. Zero (0)
			disables the time out threshold. The default is 30,
			the maximum is 1440.
	InactivityTimeout		Amount of time in minutes the switch waits before
			terminating an idle Telnet command line interface
			session. Zero (0) disables the time out threshold.
			The default is 0, the maximum is 1440.
	LocalLogEnabled		Enables (True) or disables (False) the saving of log
			information on the switch. The default is True.
	RemoteLogEnabled		Enables (True) or disables (False) the recording of
			the switch event log on a remote host that supports
			the syslog protocol. The default is False.
	RemoteLogHostAddress		The IP address of the host that will receive the
			switch event log information if remote logging is
			enabled. The default is 10.0.0.254.
	NTPClientEnabled		Enables (True) or disables (False) the Network
			Time Protocol (NTP) client on the switch. This
			client enables the switch to synchronize its time
			with an NTP server. This feature supports NTP
			version 4 and is compatible with version 3. An
			Ethernet connection to the server is required and
			you must first set an initial time and date on the
			switch. The synchronized time becomes effective
			immediately. The default is False.
	NTPServerAddress		The IP address of the NTP server from which the
			NTP client acquires the time and date. The default
			is 10.0.0.254.
	EmbeddedGUIEnabled		Enables (True) or disables (False) the SANsurfer
			Switch Manager Web applet. Changing this
			parameter to False while the applet is running will
			terminate the applet. The default is True.

A-58	59056-02 A

Image 208

Q-Logic 5200, 5202 manual Table A-14. System Configuration Settings

Contents

SANbox 5200 Series Switch Management User’s Guide SANbox 5200 Series Switch Management User’s Guide Document Revision History Table of Contents Section Managing Fabrics SANbox 5200 Series Switch Management Section Managing Switches 4.1 Snmp Configuration 4.2 Snmp Trap Configuration Changing the Default Performance View File Encryption KeySection Managing Ports 3.3 NTP Client Appendix a Command Line Interface 7.3 Shutdown Command Glossary Index102 104Page Tables 105 SANbox 5200 Series Switch Management User’s Guide 59056-02 a Intended Audience Related Materials Jdom License Technical Support AvailabilityTraining Contact Information Introduction Technical Support 59056-02 a Using SANsurfer Switch Manager Installing the Management Application SANsurfer Switch Manager For a Windows workstationFor a Linux workstation For a Solaris workstation SMS Installation for Windows SANsurfer Management Suite Chglax.bat SMS Installation for Linux SMS Installation for Solaris Change directories to the package location Install the new SANsurfer Switch Manager packageLocate and execute the file sbmoversms.sh Starting SANsurfer Switch Manager ‰ For Linux or Solaris enter the SANsurfer command Initial Startup Dialog Exiting SANsurfer Switch Manager SANsurfer Switch Manager Window Save Default Fabric View File Dialog Uninstalling SANsurfer Switch Manager SMS Uninstall Standalone Uninstall Changing the Encryption Key for the Default Fabric View File Setting SANsurfer Switch Manager Preferences Saving and Opening Fabric View Files Preferences Dialog SANsurfer Switch Manager Using Online Help Viewing Software Version and Copyright Information Topology Display SANsurfer Switch Manager User InterfaceFaceplate Display Menu Bars Topology Display Menu Faceplate Display Menu Faceplate Display Menu Topology Display Shortcut Keys Topology Display Menu Shortcut Keys Faceplate Display Shortcut Keys Faceplate Display Shortcut Keys Alt+S, L SwitchLoad Firmware Tool Bar Tool Bar Buttons Fabric Tree Fabric Tree Graphic Window Working Status IndicatorData Window and Tabs Using the Topology Display Switch and Link Status Selecting Switches and Links Working with Switches and LinksArranging Switches in the Display Opening the Faceplate Display and Topology Popup Menus Topology Data Windows Using the Faceplate Display 11. Faceplate Display Working with Ports Port Views and StatusSelecting Ports Opening the Faceplate Popup Menu Faceplate Data WindowsPage Fabric Security User Account Security Fabric Services Enabling Snmp ConfigurationClick the In-band Management Enable button Enabling In-band Management Saving a Version Snapshot Fabric TrackerViewing and Comparing Version Snapshots Exporting Version Snapshots to a File Managing the Fabric Database Adding a Fabric Add a New Fabric Dialog Removing a Fabric Opening a Fabric View FileSaving a Fabric View File Rediscovering a Fabric Deleting Switches and Links Adding a New Switch to a Fabric Replacing a Failed Switch Displaying Fabric Information Topology Display Switch and Status Icons Fabric Status Displaying the Event Browser Events Browser Severity Levels Description Icon Filtering the Event Browser Filter Events Dialog Sorting the Event Browser Saving the Event Browser to a File Devices Data Window Devices Data Window Entries Active Zone Set Data Window Active Zone Set Data Window Working with Device Information and Nicknames Link Data WindowDisplaying Detailed Device Information Managing Device Port Nicknames Exporting Device Information to a FileCreating a Nickname Deleting a Nickname Editing a NicknameExporting Nicknames to a File Zoning a Fabric Importing a Nicknames FileZoning Concepts Zones Soft Zones Aliases Access Control List Hard ZonesZone Sets Zoning Database Managing the Zoning Database Using the Zoning WizardManaging the zoning database consists of the following Editing the Zoning Database Edit Zoning Dialog Edit Zoning Dialog Tool Bar Buttons and Icons Create Alias button create another name for a set of objects Configuring the Zoning Database Interop Auto Save Saving the Zoning Database to a File Default VisibilityRestoring the Zoning Database from a File Restoring the Default Zoning Database Removing All Zoning Definitions Managing Zone Sets Creating a Zone Set Copying a Zone to a Zone Set Activating and Deactivating a Zone SetRemoving a Zone from a Zone Set or from All Zone Sets Managing Zones Removing a Zone SetManaging zones involves the following Creating a Zone in a Zone Set Adding Zone Members Renaming a Zone or a Zone Set Removing a Zone MemberRemoving a Zone from a Zone Set Removing a Zone from All Zone Sets Managing Aliases Changing Zone TypesCreating an Alias Adding a Member to an Alias Removing an Alias from All Zones Merging Fabrics and Zoning Zone Merge Failure Zone Merge Failure Recovery Managing Switches Managing User Accounts Factory User Accounts User Account Administration Dialog Add Account Creating User Accounts User Account Administration Dialog Remove Account Removing a User Account Changing a User Account Password User Account Administration Dialog Change Password User Account Administration Dialog Modify Account Modifying a User Account Displaying Switch Information Faceplate Display Switch Information Switch Data Window Switch Data Window Entries Ratov Displaying Detailed Device Information on page 3-17for Port Statistics Data Window Port Information Data Window Configured Zonesets Data Windows Configured Zonesets Data Window Configuring Port Threshold Alarms Port Threshold Alarm Configuration Dialog Paging a Switch EventCount Sample Window Setting the Date/Time and Enabling NTP Client Resetting a Switch Switch Resets Type Description Using the Configuration Wizard Configuring a SwitchSwitch Properties Symbolic Name Switch Administrative States Switch Administrative States Domain ID and Domain ID Lock Fabric Device Management Interface Broadcast Support Interop Mode for ZoningIn-band Management Timeout Values Timeout ValuesLegacy Port Address Format Network Properties 10. Network Properties Dialog IP Configuration IP Configuration Parameters Remote Logging NTP Client Snmp Properties 11. Snmp Properties Dialog Snmp Configuration Snmp Configuration Parameters Snmp Trap Configuration Snmp Trap Configuration Parameters Archiving a Switch Restoring a Switch 12. Restore Dialogs Full and Selective Restoring the Factory Default Configuration Factory Default Configuration Settings Factory Default Configuration Settings Downloading a Support File Upgrading the Switch Using License Keys 13. Features License Key Dialog Installing Firmware Displaying Hardware Status 15. Hardware Status LEDs Managing Ports Displaying Port Information Displaying Port Types Monitoring Port StatusPort Types Displaying Port Operational States Displaying Port SpeedsPort Operational States Port Speeds Displaying Transceiver Media Status Port Transceiver Media View Port Statistics Data Window Entries LIP ALPD,ALPS Port Statistics Data Window Entries Port Information Data Window Entries Port Information Data Window Entries Configuring Ports Port Properties Dialog Changing Port Administrative States Port Administrative States Changing Port Speeds Changing Port Types Stream Guard Scan Device Changing Port Symbolic Name Using the Extended Credits Wizard Resetting a Port Designate Donor Ports Testing Ports Port Loopback Test Dialog Managing Ports Graphing Port Performance Fabric View Graphs Starting SANsurfer Performance Viewer Exiting SANsurfer Performance Viewer Save Default Performance View File Dialog Saving and Opening Performance View Files Changing the Default Performance View File Encryption Key Setting SANsurfer Performance Viewer Preferences Setting the Polling Frequency Displaying Graphs Arranging Graphs in the Display Customizing Graphs Managing Ports Graphing Port Performance Printing Graphs Rescaling a Selected GraphSaving Graph Statistics to a File Managing Ports Graphing Port Performance 59056-02 a Command Line Interface Logging On to a Switch User Accounts Working with Switch Configurations Modifying a Configuration Backing up and Restoring Switch Configurations Ftp ipaddress Date, configswitch16910112003, for example Commands Command syntax is as followsCommand keyword keyword value Table A-1. Command-Line Completion Table A-2. Commands Listed by Authority Level Admin Session Commands Admin Command AuthoritySyntax Keywords Alias Command Syntax alias Remove alias memberlist Members aliasRename aliasold aliasnew Config Command Syntax configKeywords activate configname Edit configname Restore Manager Archive function are not compatible with the ConfigRestore command Save configname # ftp symbolicname or ipaddress Download the file to the workstation Create Support Command Admin sessionFollowing is an example of the Create Support command Create support You have transferred 43430 bytes in 1 files Syntax date Date CommandKeywords MMDDhhmmCCYY Feature Command Syntax featureKeywords add licensekey Log Authority Admin Firmware Install CommandSyntax firmware install Hardreset Command Syntax Help Command Keywords commandSyntax help command keyword Authority None History Command Authority None Syntax history Hotreset Command Hotreset Image Command Ftp Ftp switchname Wait for the unpack to complete Lip Command Following is an example of the Lip commandReinitializes the specified loop port Lip portnumber Passwd Command Syntax passwd accountname Keywords accountname Syntax ping ipaddress Ping CommandKeywords ipaddress Ps Command Following is an example of the Ps commandSyntax Examples Displays current system process information Closes the Telnet session Quit CommandSyntax quit, exit, or logout Reset Command Config configname System Table A-3. Switch Configuration DefaultsZoning Table A-4. Port Configuration Defaults Table A-5. Port Threshold Alarm Configuration Defaults Table A-6. Zoning Configuration Defaults Table A-7. Snmp Configuration Defaults Table A-8. System Configuration Defaults Set Command Syntax set Switch state Setup optionPort option Set Config Command Set configTable A-9. Set Config Port Parameters Port portnumber Command Line Interface Set Config Command Table A-9. Set Config Port Parameters Table A-10. Set Config Switch Parameters Number of milliseconds the switch Table A-10. Set Config Switch Parameters Table A-11. Set Config Threshold Parameters Threshold Table A-12. Set Config Zoning Parameters Arbff Following is an example of the Set Config Switch command Following is an example of the Set Config Threshold command To discard this configuration use the config cancel command Following is an example of the Set Config Zoning command Attributes Set Log Command Set logArchive Clear Display filter Level filter Port portlist SaveStart Stop Set Port Command Disables the port by removing power from the port lasers Port from accepting a device loginDown Set Setup Command Set setupTable A-13. Snmp Configuration Settings Snmp System Table A-14. System Configuration Settings Table A-14. System Configuration Settings Setup snmp Following is an example of the Set Setup System command SANbox Manager admin # set setup system Show Command Alarm optionKeywords about Broadcast Fdmi portwwn Log option Ns option PagebreakPerf option Table A-15. Show Port Parameters Lipalpdalps Post log Steering domainid Table A-16. Switch Operational Parameters Support Topology Displays all connected devicesUsers Version Following is an example of the Show Domains command Following is an example of the Show Fabric command Following is an example of the Show Fdmi command Following is an example of the Show Fdmi WWN command Following is an example of the Show NS domainID command Following is an example of the Show NS local domain commandFollowing is an example of the Show NS portID command Following is an example of the Show Interface command Collisions0 txqueuelen100 Following is an example of the Show Port command PL-XPL-VC-SG3-22 Following is an example of the Show Switch command Following is an example of the Show Topology command Command Line Interface Show Command Following is an example of the Show Version command Show Config Command Show config Following is an example of the Show Config Switch command Following is an example of the Show Config Threshold command Following is an example of the Show Config Zoning command Show Log Command Show logNumber of events Component Settings LevelOptions Port Following is an example of the Show Log Options command Following is an example of the Show Log Level commandFollowing is an example of the Show Log command Show Perf Command Errors portnumber Following is an example of the Show Perf Byte command Show setup Show Setup CommandMfg Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Power from the switch Shutdown CommandShutdown Test Command TestPort portnumber testtype Status Admin start Command Line Interface Test Command Examples The following is an example of the Uptime command Uptime CommandAuthority None Syntax uptime User Command Following is an example of the User Add command Following is an example of the User Edit command Following is an example of the User Delete command Following is an example of the User List command Following is an example of the Whoami command Whoami CommandWhoami Zone Command Syntax zone Members zone Remove zone memberlistRename zoneold zonenew Type zone zonetype Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zoneset Rename zonesetold zonesetnew Remove zoneset zonelistZones zoneset Opens a Zoning Edit session Zoning CommandHistory Limits Table A-17. Zoning Database Limits Following is an example of the Zoning Limits command E1JBOD1 E2JBOD2 Following is an example of the Zoning List command 108 59056-02 a Access Control List Zone Administrative StateAlarm BootP Class 3 Service Configured Zone SetsDefault Visibility Fabric Management Switch Input Power LED Inter-Switch LinkMaintenance Button Maintenance Mode Zoning Database Small Form-Factor PluggableSoft Zone Target Index Index-2 59056-02 a 59056-02 a Index-3 Index-4 59056-02 a 59056-02 a Index-5 Index-6 59056-02 a