Lipalpdalps | Q-Logic 5200, 5202 guide

A – Command Line Interface			0
A – Command Line Interface
Show Command

		Table A-15. Show Port Parameters (Continued)
		Table A-15. Show Port Parameters (Continued)

	Entry		Description

	EpConnects		Number of times an E_Port connected through ISL
			negotiation.
	FBusy		Number of times the switch sent a F_BSY because Class 2
			frame could not be delivered within ED_TOV time. Number
			of class 2 and class 3 fabric busy (F_BSY) frames
			generated by this port in response to incoming frames.
			This usually indicates a busy condition on the fabric or
			N_Port that is preventing delivery of this frame.
	Flowerrors		Received a frame when there were no available credits.
	FReject		Number of frames from devices that were rejected.
	InvalidCRC		Invalid CRC detected.
	InvalidDestAddr		Invalid destination address detected.
	LIP_AL_PD_ALPS		Number of F7, AL_PS LIPs, or AL_PD (vendor specific)
			resets, performed.
	LIP_F7_AL_PS		This LIP is used to reinitialize the loop. An L_Port,
			identified by AL_PS, may have noticed a performance
			degradation and is trying to restore the loop.
	LIP_F8_AL_PS		This LIP denotes a loop failure detected by the L_Port
			identified by AL_PS.
	LIP_F7_F7		A loop initialization primitive frame used to acquire a valid
			AL_PA.
	LIP_F8_F7		A loop initialization primitive frame used to indicate that a
			loop failure has been detected at the receiver.
	Link Failures		Number of optical link failures detected by this port. A link
			failure is a loss of synchronization or a loss of signal while
			not in the offline state. A loss of signal causes the switch to
			attempt to re-establish the link. If the link is not
			re-established, a link failure is counted. A link reset is
			performed after a link failure.
	Login		Number of device logins
	Logout		Number of device logouts
	LoopTimeouts		A two (2) second timeout as specified by FC-AL-2.
	LossOfSync		Number of synchronization losses (>100 ms) detected by
			this port. A loss of synchronization is detected by receipt of
			an invalid transmission word.

A-64	59056-02 A

Image 214

Q-Logic 5200, 5202 manual Lipalpdalps

Contents

SANbox 5200 Series Switch Management User’s Guide SANbox 5200 Series Switch Management User’s Guide Document Revision History Table of Contents Section Managing Fabrics SANbox 5200 Series Switch Management Section Managing Switches Section Managing Ports 4.1 Snmp Configuration 4.2 Snmp Trap ConfigurationChanging the Default Performance View File Encryption Key 3.3 NTP Client Appendix a Command Line Interface 7.3 102 Shutdown CommandGlossary Index 104Page Tables 105 SANbox 5200 Series Switch Management User’s Guide 59056-02 a Intended Audience Related Materials Jdom License Training Technical SupportAvailability Contact Information Introduction Technical Support 59056-02 a Using SANsurfer Switch Manager Installing the Management Application For a Linux workstation SANsurfer Switch ManagerFor a Windows workstation For a Solaris workstation SMS Installation for Windows SANsurfer Management Suite Chglax.bat SMS Installation for Linux SMS Installation for Solaris Change directories to the package location Install the new SANsurfer Switch Manager packageLocate and execute the file sbmoversms.sh Starting SANsurfer Switch Manager ‰ For Linux or Solaris enter the SANsurfer command Initial Startup Dialog Exiting SANsurfer Switch Manager SANsurfer Switch Manager Window Save Default Fabric View File Dialog Uninstalling SANsurfer Switch Manager SMS Uninstall Standalone Uninstall Changing the Encryption Key for the Default Fabric View File Setting SANsurfer Switch Manager Preferences Saving and Opening Fabric View Files Preferences Dialog SANsurfer Switch Manager Using Online Help Viewing Software Version and Copyright Information Topology Display SANsurfer Switch Manager User InterfaceFaceplate Display Menu Bars Topology Display Menu Faceplate Display Menu Faceplate Display Menu Topology Display Shortcut Keys Topology Display Menu Shortcut Keys Faceplate Display Shortcut Keys Faceplate Display Shortcut Keys Alt+S, L SwitchLoad Firmware Tool Bar Tool Bar Buttons Fabric Tree Fabric Tree Graphic Window Working Status IndicatorData Window and Tabs Using the Topology Display Switch and Link Status Selecting Switches and Links Working with Switches and LinksArranging Switches in the Display Opening the Faceplate Display and Topology Popup Menus Topology Data Windows Using the Faceplate Display 11. Faceplate Display Working with Ports Port Views and StatusSelecting Ports Opening the Faceplate Popup Menu Faceplate Data WindowsPage Fabric Security User Account Security Click the In-band Management Enable button Fabric ServicesEnabling Snmp Configuration Enabling In-band Management Saving a Version Snapshot Fabric TrackerViewing and Comparing Version Snapshots Exporting Version Snapshots to a File Managing the Fabric Database Adding a Fabric Add a New Fabric Dialog Saving a Fabric View File Removing a FabricOpening a Fabric View File Rediscovering a Fabric Deleting Switches and Links Adding a New Switch to a Fabric Replacing a Failed Switch Displaying Fabric Information Topology Display Switch and Status Icons Fabric Status Displaying the Event Browser Events Browser Severity Levels Description Icon Filtering the Event Browser Filter Events Dialog Sorting the Event Browser Saving the Event Browser to a File Devices Data Window Devices Data Window Entries Active Zone Set Data Window Active Zone Set Data Window Working with Device Information and Nicknames Link Data WindowDisplaying Detailed Device Information Managing Device Port Nicknames Exporting Device Information to a FileCreating a Nickname Deleting a Nickname Editing a NicknameExporting Nicknames to a File Zoning a Fabric Importing a Nicknames FileZoning Concepts Zones Soft Zones Aliases Access Control List Hard ZonesZone Sets Zoning Database Managing the Zoning Database Using the Zoning WizardManaging the zoning database consists of the following Editing the Zoning Database Edit Zoning Dialog Edit Zoning Dialog Tool Bar Buttons and Icons Create Alias button create another name for a set of objects Configuring the Zoning Database Interop Auto Save Saving the Zoning Database to a File Default VisibilityRestoring the Zoning Database from a File Restoring the Default Zoning Database Removing All Zoning Definitions Managing Zone Sets Creating a Zone Set Copying a Zone to a Zone Set Activating and Deactivating a Zone SetRemoving a Zone from a Zone Set or from All Zone Sets Managing Zones Removing a Zone SetManaging zones involves the following Creating a Zone in a Zone Set Adding Zone Members Removing a Zone from a Zone Set Renaming a Zone or a Zone SetRemoving a Zone Member Removing a Zone from All Zone Sets Managing Aliases Changing Zone TypesCreating an Alias Adding a Member to an Alias Removing an Alias from All Zones Merging Fabrics and Zoning Zone Merge Failure Zone Merge Failure Recovery Managing Switches Managing User Accounts Factory User Accounts User Account Administration Dialog Add Account Creating User Accounts User Account Administration Dialog Remove Account Removing a User Account Changing a User Account Password User Account Administration Dialog Change Password User Account Administration Dialog Modify Account Modifying a User Account Displaying Switch Information Faceplate Display Switch Information Switch Data Window Switch Data Window Entries Ratov Displaying Detailed Device Information on page 3-17for Port Statistics Data Window Port Information Data Window Configured Zonesets Data Windows Configured Zonesets Data Window Configuring Port Threshold Alarms Port Threshold Alarm Configuration Dialog Count Paging a SwitchEvent Sample Window Setting the Date/Time and Enabling NTP Client Resetting a Switch Switch Resets Type Description Using the Configuration Wizard Configuring a SwitchSwitch Properties Symbolic Name Switch Administrative States Switch Administrative States Domain ID and Domain ID Lock Fabric Device Management Interface Broadcast Support Interop Mode for ZoningIn-band Management Timeout Values Timeout ValuesLegacy Port Address Format Network Properties 10. Network Properties Dialog IP Configuration IP Configuration Parameters Remote Logging NTP Client Snmp Properties 11. Snmp Properties Dialog Snmp Configuration Snmp Configuration Parameters Snmp Trap Configuration Snmp Trap Configuration Parameters Archiving a Switch Restoring a Switch 12. Restore Dialogs Full and Selective Restoring the Factory Default Configuration Factory Default Configuration Settings Factory Default Configuration Settings Downloading a Support File Upgrading the Switch Using License Keys 13. Features License Key Dialog Installing Firmware Displaying Hardware Status 15. Hardware Status LEDs Managing Ports Displaying Port Information Displaying Port Types Monitoring Port StatusPort Types Port Operational States Displaying Port Operational StatesDisplaying Port Speeds Port Speeds Displaying Transceiver Media Status Port Transceiver Media View Port Statistics Data Window Entries LIP ALPD,ALPS Port Statistics Data Window Entries Port Information Data Window Entries Port Information Data Window Entries Configuring Ports Port Properties Dialog Changing Port Administrative States Port Administrative States Changing Port Speeds Changing Port Types Stream Guard Scan Device Changing Port Symbolic Name Using the Extended Credits Wizard Resetting a Port Designate Donor Ports Testing Ports Port Loopback Test Dialog Managing Ports Graphing Port Performance Fabric View Graphs Starting SANsurfer Performance Viewer Exiting SANsurfer Performance Viewer Save Default Performance View File Dialog Saving and Opening Performance View Files Changing the Default Performance View File Encryption Key Setting SANsurfer Performance Viewer Preferences Setting the Polling Frequency Displaying Graphs Arranging Graphs in the Display Customizing Graphs Managing Ports Graphing Port Performance Printing Graphs Rescaling a Selected GraphSaving Graph Statistics to a File Managing Ports Graphing Port Performance 59056-02 a Command Line Interface Logging On to a Switch User Accounts Working with Switch Configurations Modifying a Configuration Backing up and Restoring Switch Configurations Ftp ipaddress Date, configswitch16910112003, for example Command keyword keyword value CommandsCommand syntax is as follows Table A-1. Command-Line Completion Table A-2. Commands Listed by Authority Level Admin Session Commands Syntax Admin CommandAuthority Keywords Alias Command Syntax alias Remove alias memberlist Members aliasRename aliasold aliasnew Keywords activate configname Config CommandSyntax config Edit configname Restore command RestoreManager Archive function are not compatible with the Config Save configname # ftp symbolicname or ipaddress Download the file to the workstation Following is an example of the Create Support command Create Support CommandAdmin session Create support You have transferred 43430 bytes in 1 files Syntax date Date CommandKeywords MMDDhhmmCCYY Keywords add licensekey Feature CommandSyntax feature Log Authority Admin Firmware Install CommandSyntax firmware install Hardreset Command Syntax Syntax help command keyword Help CommandKeywords command Authority None History Command Authority None Syntax history Hotreset Command Hotreset Image Command Ftp Ftp switchname Wait for the unpack to complete Reinitializes the specified loop port Lip CommandFollowing is an example of the Lip command Lip portnumber Passwd Command Syntax passwd accountname Keywords accountname Syntax ping ipaddress Ping CommandKeywords ipaddress Syntax Examples Ps CommandFollowing is an example of the Ps command Displays current system process information Closes the Telnet session Quit CommandSyntax quit, exit, or logout Reset Command Config configname System Table A-3. Switch Configuration DefaultsZoning Table A-4. Port Configuration Defaults Table A-5. Port Threshold Alarm Configuration Defaults Table A-6. Zoning Configuration Defaults Table A-7. Snmp Configuration Defaults Table A-8. System Configuration Defaults Set Command Syntax set Switch state Setup optionPort option Table A-9. Set Config Port Parameters Set Config CommandSet config Port portnumber Command Line Interface Set Config Command Table A-9. Set Config Port Parameters Table A-10. Set Config Switch Parameters Number of milliseconds the switch Table A-10. Set Config Switch Parameters Table A-11. Set Config Threshold Parameters Threshold Table A-12. Set Config Zoning Parameters Arbff Following is an example of the Set Config Switch command Following is an example of the Set Config Threshold command To discard this configuration use the config cancel command Following is an example of the Set Config Zoning command Attributes Archive Set Log CommandSet log Clear Display filter Level filter Start Port portlistSave Stop Set Port Command Disables the port by removing power from the port lasers Port from accepting a device loginDown Table A-13. Snmp Configuration Settings Set Setup CommandSet setup Snmp System Table A-14. System Configuration Settings Table A-14. System Configuration Settings Setup snmp Following is an example of the Set Setup System command SANbox Manager admin # set setup system Keywords about Show CommandAlarm option Broadcast Fdmi portwwn Log option Perf option Ns optionPagebreak Table A-15. Show Port Parameters Lipalpdalps Post log Steering domainid Table A-16. Switch Operational Parameters Support Users TopologyDisplays all connected devices Version Following is an example of the Show Domains command Following is an example of the Show Fabric command Following is an example of the Show Fdmi command Following is an example of the Show Fdmi WWN command Following is an example of the Show NS domainID command Following is an example of the Show NS local domain commandFollowing is an example of the Show NS portID command Following is an example of the Show Interface command Collisions0 txqueuelen100 Following is an example of the Show Port command PL-XPL-VC-SG3-22 Following is an example of the Show Switch command Following is an example of the Show Topology command Command Line Interface Show Command Following is an example of the Show Version command Show Config Command Show config Following is an example of the Show Config Switch command Following is an example of the Show Config Threshold command Following is an example of the Show Config Zoning command Number of events Show Log CommandShow log Component Options SettingsLevel Port Following is an example of the Show Log Options command Following is an example of the Show Log Level commandFollowing is an example of the Show Log command Show Perf Command Errors portnumber Following is an example of the Show Perf Byte command Show setup Show Setup CommandMfg Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Power from the switch Shutdown CommandShutdown Port portnumber testtype Test CommandTest Status Admin start Command Line Interface Test Command Examples The following is an example of the Uptime command Uptime CommandAuthority None Syntax uptime User Command Following is an example of the User Add command Following is an example of the User Edit command Following is an example of the User Delete command Following is an example of the User List command Following is an example of the Whoami command Whoami CommandWhoami Zone Command Syntax zone Rename zoneold zonenew Members zoneRemove zone memberlist Type zone zonetype Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zoneset Rename zonesetold zonesetnew Remove zoneset zonelistZones zoneset Opens a Zoning Edit session Zoning CommandHistory Limits Table A-17. Zoning Database Limits Following is an example of the Zoning Limits command E1JBOD1 E2JBOD2 Following is an example of the Zoning List command 108 59056-02 a Alarm Access Control List ZoneAdministrative State BootP Default Visibility Class 3 ServiceConfigured Zone Sets Fabric Management Switch Maintenance Button Input Power LEDInter-Switch Link Maintenance Mode Soft Zone Zoning DatabaseSmall Form-Factor Pluggable Target Index Index-2 59056-02 a 59056-02 a Index-3 Index-4 59056-02 a 59056-02 a Index-5 Index-6 59056-02 a