Texas Instruments TNETX3270 specifications Test measurement

Page 52

TNETX3270

ThunderSWITCH 24/3 ETHERNET SWITCH

WITH 24 10-MBIT/S PORTS AND 3 10-/100-MBIT/S PORTS

SPWS043B ± NOVEMBER 1997 ± REVISED APRIL 1999

PARAMETER MEASUREMENT INFORMATION

Outputs are driven to a minimum high-logic level of 3.3 V and to a maximum low-logic level of 0 V.

Output transition times are specified as follows: For a high-to-low transition on either an input or output signal, the level at which the signal is said to be no longer high is 1.4 V and the level at which the signal is said to be low is 1.4 V. For a low-to-high transition, the level at which the signal is said to be no longer low is 0.8 V and the level at which the signal is said to be high is 2 V, as shown in the following.

The rise and fall times are not specified but are assumed to be those of standard TTL devices, which are typically 1.5 ns.

2 V (high)

1.4 V

0.8 V (low)

test measurement

The test-and-load circuit shown in Figure 12 represents the programmable load of the tester pin that is used to verify timing parameters of the TNETX3270 output signals.

IOL

Test

Point

VLOAD

CL

TTL

Output

Under

Test

			IOH
		TTL OUTPUT TEST LOAD
Where: IOL	=	Refer to IOL in recommended operating conditions.
IOH	=	Refer to IOH in recommended operating conditions.
VLOAD =		1.5	V, typical dc-level verification or
		1.5	V, typical timing verification
CL	=	45 pF, typical load-circuit capacitance

Figure 12. Test-and-Load Circuit

52	POST OFFICE BOX 655303 •DALLAS, TEXAS 75265

Image 52

Contents TNETX3270 ThunderSWITCH 24/3 ETHERNET Switch With 24 10-MBIT/S Ports and 3 10-/100-MBIT/S PortsWith 24 10-MBIT/S Ports and 3 10-/100-MBIT/S Ports DescriptionThunderSWITCH 24/3 ETHERNET ContentsPGV Package TOP View ThunderSWITCH  24/3Terminal Internal Description Name RESISTOR³ 10-/100-Mbit/s MAC interface ports 24±26³ Terminal Internal Description Name ResistorTerminal Functions 10-/100-Mbit/s MAC interface ports 24±26 ²Sdram interface Dras DcasDclk DrasHost DIO interface Eeprom interface Serial MII management PHY interfaceJtag interface Summary of signal terminals by signal group function Power interfaceMiscellaneous Internal Register and Statistics Memory Map DIO register groupsVlan Byte DIO Address Detailed DIO Register MapSIO VLAN1QID VLAN0QID VLAN3QID VLAN2QIDVLAN5QID VLAN4QID VLAN7QID VLAN6QIDVLAN17QID VLAN16QID VLAN19QID VLAN18QIDVLAN21QID VLAN20QID VLAN23QID VLAN22QIDIntenable TNETX3270 reset reinitializes the TNETX3270 0x40000x5FFFFindnode23±16 Findnode31±24 Findnode39±32 Findnode47±40 Findcontrol Findnode7±0 Findnode15±8Interface description State of DIO signals during hardware resetReceiving/transmitting management frames Network management port Frame format on the NM port Vlan ID FCSTpid TCI CRCMII serial management interface PHY management Mbit/s and 10-/100-Mbit/s MAC interface receive controlGiant long frames Short framesReceive filtering of frames Data transmissionTransmit control Adaptive performance optimization APO transmit pacingReceive versus transmit priority Uplink pretaggingSource-Port Pretag Encoding Source PortTAG Received Pretag Port AssignmentsPort 27 NM Edio TNETX3270 Eclk SCL SDA Eeprom interfaceGND Outcome Stop Load Initd ² Fault LED Eclk Interaction of Eeprom load with the SIO registerSummary of Eeprom load outcomes Summary of Eeprom Load OutcomesJtag interface Jtag Instruction OpcodesHighz instruction LED interfaceHardware configurations LED Status Bit Definitions and Shift OrderLamp test Multi-LED displayMbit/s Interface Connections TNETX3270 TNETE2008 TerminalPort CLK Sync TXD3 M03TXD M04TXDM06TXD M03COLConnecting to TNETE2008 PHY² 10-/100-Mbit/s port configuration Switch TNETE2101 Terminal10-/100-Mbit/s MAC interfaces ports 24±26 100-Mbit/s Interface ConnectionsDuplex Configuration ± MxxFORCEHD Speed Configuration ± MxxFORCE1010-/100-Mbit/s port configuration in a nonmanaged switch 10-/100-Mbit/s port configuration in a managed switch Sdram interface TNETX3270 Terminal Interface to SDRAMs Sdram Terminals Not Driven by the TNETX3270Terminals Sdram Terminal Function TNETX3270 Held Sdram Terminal Terminal FunctionTNETX3270 State Terminal During Reset SDRAM-type and quantity indicationInitialization RefreshVlan support Frame routingIale Ieee Std 802.1Q headers ± reception Address maintenanceIeee Std 802.1Q headers ± transmission Aging algorithms Spanning-tree supportFrame-routing determination Frame-Routing Algorithm SPWS043B ± November 1997 ± Revised April Port mirroring CDEPort trunking/load sharing Flow controlCollision-based flow control Ieee Std 802.3 flow controlPause frame reception Internal wrap test Duplex wrap test PHY TNETX3270Copy to uplink MIN NOM MAX Unit Recommended operating conditionsParameter Test Conditions MIN TYP MAX Unit Test measurement MIN MAX Unit Parameter MIN MAX UnitTiming requirements see Note 7 and Figure 10-/100-Mbit/s MAC interface10-/100-Mbit/sreceive ports 24, 25 Timing requirements see Figure 10-/100-Mbit/stransmit ports 24, 25,Sdram command to command see Figure TdDA Delay time, from Dclk ↑ to DA Invalid Sdram subcycleDclk Dras DcasDIO/DMA write cycle DIO/DMA interfaceSDATA7± Z SDATA0 DIO/DMA read cycle Serial MII Management Read/Write Cycle Eeprom Parameter TNETX3150 TNETX3150A Unit MIN MAXTdLEDDATA Delay time, from LEDCLK↑ to 1st LED invalid ² During hard reset, Ledclk runs continuouslyPower-up Oscin and Reset Timing requirements see Figure TsuRESET Setup time Low before Oscin ↑ThRESET Hold time Low after Oscin ↑ TtOSCIN Transition time, Oscin rise and fallMechanical Data Important Notice