Installation, Mains connection, Operation

Distance between the saw blade's outer edge and the riving knife needs to be 3 – 5 mm.

The riving knife must be in align- ment with the saw blade.

ADanger!

The riving knife is one of the

safety devices and must be correctly installed for safe operation.

Only if realignment of the riving knife is necessary:

3.Loosen table insert (49) and remove from table.

Setting the distance to the saw blade:

4.Loosen hexagon socket head cap screw (50) (to do so, turn hexagon socket head cap screw counter- clockwise!)

5.Pull riving knife (51) fully up against the stop and align: the gap between saw blade and riving knife must be 3 to 5 mm.

6.Tighten hexagon socket head cap screw (50) (to do so, turn hexagon socket head cap screw clockwise!)

Lateral alignment:

riving knife and saw blade (52) must be in true alignment.

7.Loosen hexagon nut (53) and adjust vertical alignment with machine screw (54).

8.Lock machine screw with (53).

9.Loosen both hexagon socket screws (55).

10.Align riving knife flush with the saw blade.

11.Tighten both hexagon socket screws (55).

12. Reinstall table insert.

Blade guard installation

1.Raise saw blade fully.

2.Install blade guard (57) on riving knife (56).

5657

7.2Installation

There are two ways to ensure a firm stand of the machine:

mounted on floor stand (accessory);

mounted on sturdy table or bench.

ENGLISH

7.3Mains connection

BDanger! High voltage

ξOperate this machine in dry sur- roundings only.

ξOperate machine only on a power source meeting the following requirements (see also “Techni- cal Specifications”):

outlets properly installed, earthed, and tested.

mains voltage and system fre- quency conform to the voltage and frequency shown on the machine´s rating label;

fuse protection by a residual current operated device (RCD) of 30 mA sensitivity;

System impedance Zmax at the interconnection point (house service connection) 0.35 Ohm maximum.

3 Note:

Check with your local Electricity Board or electrician if in doubt whether your house service connection meets these requirements.

ξPosition power supply cable so it does not interfere with the work and is not damaged.

ξProtect power supply cable from heat, aggressive liquids and sharp edges.

ξUse only rubber-jacketed exten- sion cables with sufficient lead cross-section (see “Technical Specifications”).

ξDo not pull on power supply cable to unplug.

8. Operation

ARisk of injury!

This saw may only be operated

by one person at a time. Other per- sons shall stay only at a distance to the saw for the purpose of feeding or removing stock.

Before starting work, check to see that the following are in proper work- ing order:

power cable and plug;

TS 250 specifications

The Metabo TS 250 is a powerful and versatile table saw designed to meet the demands of both professional woodworkers and serious DIY enthusiasts. Renowned for its robust build quality and precision, this saw is a reliable choice for a variety of woodworking tasks, from rip cuts to cross cuts.

One of the standout features of the Metabo TS 250 is its powerful motor, which delivers consistent performance, allowing users to tackle even the toughest materials with ease. The saw is equipped with a 3 HP motor that provides ample power for cutting hardwoods and thicker sheets of material, ensuring clean and precise cuts every time. The motor is also designed for efficiency, minimizing energy consumption while maximizing performance.

The TS 250 boasts a durable and sturdy work surface, with a high-quality cast iron table that provides ample workspace and stability. The smooth surface allows for easy movement of materials and enhances the overall cutting experience. Additionally, the table features an adjustable fence system that enables quick and accurate adjustments, ensuring precise cuts with minimal effort.

Safety is a key consideration in the design of the Metabo TS 250. It is equipped with an integrated riving knife that helps prevent kickback by maintaining a safe distance between the blade and the wood being cut. The blade guard can be easily adjusted or removed for more complex cuts, while the emergency stop switch offers peace of mind by allowing quick shutdown in case of any unexpected incidents.

In terms of technology, the Metabo TS 250 comes with a range of features that enhance its usability. The saw offers variable blade speed options, allowing users to adjust the speed based on the material being cut. This flexibility not only improves the quality of the cut but also extends the life of the blade.

Another impressive characteristic of the TS 250 is its portability. Although it is designed as a stationary saw, it features built-in handles for easy transportation and setup in various work environments. This makes it a suitable option for contractors and tradespeople who require mobility without sacrificing performance.

Overall, the Metabo TS 250 stands out as a premier choice in the table saw market, combining power, precision, safety, and portability. With its user-friendly features and advanced technology, it’s an investment that will serve woodworkers for years to come, fulfilling both professional and hobbyist needs.