Fuji Labs ZSP Installation, Selection of installation site, Selection of gas sampling location

Page 10

4. INSTALLATION

Danger

This product is not explosion-proof. Do not use it in explosive gas-rich atmosphere. Otherwise, serious accidents such as explosion and fire may be caused.

Caution

Installation, carrying and relocation must be made by a qualified contractor or your dealer. Incorrect installation results in falling accidents, electric shocks or fire accidents.

The gas analyzer is heavy. Special care should be taken for installation to prevent trouble or injury due to falling or dropping of the analyzer.

When the gas analyzer needs to be lifted, be sure to put on gloves. Do not hold it with bare hands to prevent injury.

This product must be installed in a place that meets the conditions specified in the ‘instruction manual.’ Use in a place that is outside the given installation conditions may cause an electric shock, fire or mal- function.

During installation work, attention should be paid not to allow entrance of wire fragments, etc. into the product. Otherwise, a fire, trouble or malfunction may be caused.

There are a number of conditions which must be met for operating the gas analyzer stably over a long time.

4.1Selection of installation site

A site which satisfies the following conditions should be selected for installation of the analyzer.

(1)A place which is near the gas sampling location

(2)A place which is not exposed to direct sunlight or heat radiated from a high temperature object (One which is not exposed to rain or water splash in case of indoor type)

(3)A place which has a clean atmosphere (dust and corrosive gas not present)

(4)A place with a minimum of vibration

(5)A place where daily variation in temperature is minimum

4.2Selection of gas sampling location

A place which satisfies the following conditions should be selected.

(1)A typical place where the gases to be analyzed exist

(2)Where the gases always flow without stagnation

(3)A place easy of access for maintenance and inspection

(4)Where the gases respond quickly to a change in the process operating conditions

(5)Where variation in pressure, temperature, etc. is minimum

– 2 –

Image 10
Contents Infrared GAS Analyzer Introduction RequestProhibition Iii Prohibition Others Contents Vii Composition SpecificationsOutline PreparedSelection of installation site InstallationSelection of gas sampling location Installation work Connection of cablesPiping procedure Description of Each Part Injection of clean waterSupply of external power Preparation for OperationAirtightness test Setting of temperature inside lockerWarm-up time INDICATION/OPERATION Panel SO2Function and indication of indication/operation panel This panel consists of the following functionsAdvice on Operation General operation of indication/operation panelKinds of standard gas CalibrationPreparation of standard gas Pressure regulation for standard gas cylinder Calibration concentration setting except zirconia O2 sensor Func CAL SET ENTCAL Calibration concentration setting zirconia O2 sensor CAL Comp ENT Zero Single-component analyzer Auto calibration Auto CAL Func Auto CAL Func Auto CAL ENT Auto calibration ON/OFF setting Func Hold ENT Operating procedure OperationMaintenance Routine maintenance and inspectionConditioner Centration is measured in the setting range of 0 to Periodic maintenance and inspectionOther maintenance and inspection 200ppm or more at 0.5L/minMaintenance of sampling device Gas extractor type ZBAK1Membrane filter Exploded view of diaphragm type aspirator Structure of electronic dehumidifier Structure of NO2 /NO converter Structure of Permapure dryer Maintenance of zirconia O2 sensor Others, major component figuresStandard Accessories and Spares Standard accessoriesSpares for 1 year optional Code for preparation of 1-year spares and suppliesProcessing of Heating Pipe Ends OutlineEnd processing method Grid 300mm 40mm Grid area 150 mm Check after piping Clamp supportSpecifications of tube trace Specifications of heating pipeTroubleshooting Troubleshooting of instrumentError codes and remedies Power consumption Ambient temperaturePower supply Mass weightMonth/NO2, 100ppm Standard requirements For sample gasNumber of output points and kinds of outputs Block diagram Moving average outputCalibration tolerance Automatic calibration output hold Automatic calibrationOrdering information Calibration cycle Once/day variable, up to 7 daysCode Symbols Diaglam Functions of individual components For outdoor installation type For indoor installation typeConnection Diagram Only specified outputs are wiredHead Office Instrumentation Div International Sales Dept