Fuji Labs ZSP Sample gas extracting rate Approx N/min Gas extractor, Sample inlet tube

Page 53
SO2
CO
CO2
O2
Repeatability:
Drift:
Linearity: Response time:
Output:
Contact output:
Indication:
Specifications
Type of cubicle: Measuring system:
Sampling system:
Measuring range: (Range selection: Max. rate 1:20 (except for O2))

14. SPECIFICATIONS

Outdoor, self-standing, sealed type or indoor type

Non-dispersion infrared absorption (NDIR method) for NOx, SO2, CO and CO2; zirconia method for O2.

Dry sampling electronic cooling & dehumidification system (Permapure dryer adopted)

NOx — 0 to 100 .... 2000 ppm

— 0 to 100 .... 1000 ppm

— 0 to 200 .... 2000 ppm

— 0 to 5 ........ 50%

— 0 to 10/25%

Note: Measuring range of each gas is 50 to 5000ppm, available in approved type (special order).

± 0.5% of full scale

Zero — ± 2% of full scale/week for NOx, SO2 and CO

±2% of full scale/month for O2

Span — ± 2% of full scale/week

± 2% of full scale

90% response from the inlet of cubicle SO2 : 4 min. CO : 2.5 min NO : 2 min Others : 3 min.

4 to 20mA DC (allowable load resistance 550Ω ), non-isolated. For the number of output points, see Table 1.

Each NO (1a) contact (100V AC, 1A) for error (analyzer error, calibration error) and auto calibration status

Digital indication (indicating measured value and measuring range on analyzer front panel of infrared gas analyzer)

Sample gas extracting rate: Approx. 2 N/min.

Gas extractor:

Electrical heating type (filter built in)

 

Filter mesh — 40∝ m mesh of 316 stainless steel

 

Probe

— 316 stainless steel, length 600, 800 or 1000mm

 

Flange

— JIS 5 K65AFF

Sample inlet tube:

ø 10/ ø 8mm teflon tube for CO and O2 meter and NOx and O2 meter

 

Heating tube ( ø 10/ ø 8mm teflon tube) for NOx, SO2 and O2 meter and NOx, SO2, CO

 

and O2 meter

Standard gas (3.4 N):

Standard air gas for zero calibration and O2 span calibration

 

Standard analyte/remaining N2 gas for low range span calibration and O2 zero calibration

Form verification:

Form for all components already approved

Ambient temperature:

-5 to +40° C

 

Power supply:

100± 10V AC, 50 or 60Hz

Power consumption:

Approx. 1,200 VA (excluding consent and heating tube)

Mass (weight):

Approx. 300 kg (excluding standard gas)

Finish color:

Munsell 5Y 7/1 semigloss

– 45 –

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Infrared GAS Analyzer Request IntroductionProhibition Iii Prohibition Others Contents Vii Outline SpecificationsComposition PreparedSelection of gas sampling location InstallationSelection of installation site Connection of cables Installation workPiping procedure Supply of external power Injection of clean waterDescription of Each Part Preparation for OperationWarm-up time Setting of temperature inside lockerAirtightness test SO2 INDICATION/OPERATION PanelThis panel consists of the following functions Function and indication of indication/operation panelGeneral operation of indication/operation panel Advice on OperationPreparation of standard gas CalibrationKinds of standard gas Pressure regulation for standard gas cylinder Func CAL SET ENT Calibration concentration setting except zirconia O2 sensorCAL Calibration concentration setting zirconia O2 sensor CAL Comp ENT Zero Single-component analyzer Auto calibration Auto CAL Func Auto CAL Func Auto CAL ENT Auto calibration ON/OFF setting Func Hold ENT Operation Operating procedureRoutine maintenance and inspection MaintenanceConditioner Other maintenance and inspection Periodic maintenance and inspectionCentration is measured in the setting range of 0 to 200ppm or more at 0.5L/minGas extractor type ZBAK1 Maintenance of sampling deviceMembrane filter Exploded view of diaphragm type aspirator Structure of electronic dehumidifier Structure of NO2 /NO converter Structure of Permapure dryer Others, major component figures Maintenance of zirconia O2 sensorStandard accessories Standard Accessories and SparesCode for preparation of 1-year spares and supplies Spares for 1 year optionalOutline Processing of Heating Pipe EndsEnd processing method Grid 300mm 40mm Grid area 150 mm Clamp support Check after pipingSpecifications of heating pipe Specifications of tube traceTroubleshooting of instrument TroubleshootingError codes and remedies Power supply Ambient temperaturePower consumption Mass weightNumber of output points and kinds of outputs Standard requirements For sample gasMonth/NO2, 100ppm Moving average output Block diagramOrdering information Automatic calibrationCalibration tolerance Automatic calibration output hold Calibration cycle Once/day variable, up to 7 daysCode Symbols Diaglam Functions of individual components For indoor installation type For outdoor installation typeOnly specified outputs are wired Connection DiagramHead Office Instrumentation Div International Sales Dept
Top Page Image Contents