Fuji Labs ZSP instruction manual For outdoor installation type, For indoor installation type

Page 60

OUTLINE DIAGRAM (Unit:mm)

For outdoor installation type

	1000
120	°
	°
	30
	Rc 3/8
	1400
	770
	Rc 1/2
	100
	760
	800

815

70

A-140-2-1

(key No.200)

50

620

800

Anchor plan and door opening diagram

620

Rear

Cable inlet (60 ⋅ 120

760

side

70

rectangular hole)

with plastic resin-

Front

cover (PVC)

side

1800	Anchor bolt (option)
1800	( 4 – M12 ⋅ 160 ⋅						50 )

	32						35
	32						35

100 4-φ15 hole

For indoor installation type	Anchor plan and door opening
	Anchor plan and door opening
	diagram

800	800				620
					620
	°
	30
		70		Rear	Cable inlet (60 ⋅ 120
	Rc 3/8	70		side			rectangular hole)
			760	side			rectangular hole)
						70	with plastic resin-
				Front		70

							cover (PVC)
				side			cover (PVC)
				side
	A-140-2-1
	(key No.200)
1400		1610	(1740)
					Anchor bolt (option)
850					( 4 – M12 ⋅	160 ⋅ 50 )
	770				( 4 – M12 ⋅	160 ⋅ 50 )
	770
	Rc 1/2
100						32	35
100		50
760	620	100
800	800	4- φ 15hole

– 52 –

Image 60

Contents Infrared GAS Analyzer Introduction RequestProhibition Iii Prohibition Others Contents Vii Specifications OutlineComposition PreparedInstallation Selection of installation siteSelection of gas sampling location Installation work Connection of cablesPiping procedure Injection of clean water Supply of external powerDescription of Each Part Preparation for OperationSetting of temperature inside locker Airtightness testWarm-up time INDICATION/OPERATION Panel SO2Function and indication of indication/operation panel This panel consists of the following functionsAdvice on Operation General operation of indication/operation panelCalibration Kinds of standard gasPreparation of standard gas Pressure regulation for standard gas cylinder Calibration concentration setting except zirconia O2 sensor Func CAL SET ENTCAL Calibration concentration setting zirconia O2 sensor CAL Comp ENT Zero Single-component analyzer Auto calibration Auto CAL Func Auto CAL Func Auto CAL ENT Auto calibration ON/OFF setting Func Hold ENT Operating procedure OperationMaintenance Routine maintenance and inspectionConditioner Periodic maintenance and inspection Other maintenance and inspectionCentration is measured in the setting range of 0 to 200ppm or more at 0.5L/minMaintenance of sampling device Gas extractor type ZBAK1Membrane filter Exploded view of diaphragm type aspirator Structure of electronic dehumidifier Structure of NO2 /NO converter Structure of Permapure dryer Maintenance of zirconia O2 sensor Others, major component figuresStandard Accessories and Spares Standard accessoriesSpares for 1 year optional Code for preparation of 1-year spares and suppliesProcessing of Heating Pipe Ends OutlineEnd processing method Grid 300mm 40mm Grid area 150 mm Check after piping Clamp supportSpecifications of tube trace Specifications of heating pipeTroubleshooting Troubleshooting of instrumentError codes and remedies Ambient temperature Power supplyPower consumption Mass weightStandard requirements For sample gas Month/NO2, 100ppmNumber of output points and kinds of outputs Block diagram Moving average outputAutomatic calibration Ordering informationCalibration tolerance Automatic calibration output hold Calibration cycle Once/day variable, up to 7 daysCode Symbols Diaglam Functions of individual components For outdoor installation type For indoor installation typeConnection Diagram Only specified outputs are wiredHead Office Instrumentation Div International Sales Dept