Agilent Technologies 66111A, 66309B, 66311B, D Front Panel Menus

Quick Reference - 1

Front Panel Menus - At a Glance

ADDRESS 7 Sets the GPIB Address

INTF GPIB Selects an interface (GPIB | RS232) 1

BAUDRATE 300 Selects baud rate (300 | 600 | 1200 | 2400 | 4800 | 9600) 1

PARITY NONE Selects message parity (NONE | EVEN | ODD | MARK | SPACE) 1

FLOW NONE Selects flow control (XON-XOFF | RTS-CTS | DTR-DSR | NONE) 1

LANG SCPI Selects language (SCPI | COMP) 1

REMOTE FP OFF Enables or disables Agilent 14575A remote front panel (ON | OFF)

ROM: A.00.00 Displays the firmware revision of the instrument

SN: US12345678 Displays the serial number of the instrument

*RCL 0 Recalls the instrument state

*SAV 0 Saves the present instrument state

ERROR 0 Displays the number of errors in the SCPI error queue

2 5.000V 0.104A Toggles the display between output 1 and output 2 (output 2 shown)

1 12.000V 1 0.204A Measures the output voltage and current (output 1 shown)

1 12.500V MAX Measures the peak output voltage 2

1 1.000V MIN Measures the minimum output voltage 2

1 12.330V HIGH Measures the high level of a voltage pulse waveform 2

1 0.080V LOW Measures the low level of a voltage pulse waveform 2

1 12.000V RMS Measures the rms voltage 2

1 0.350A MAX Measures the peak output current 2

1 0.050A MIN Measures the minimum output current 2

1 0.400A HIGH Measures the high level of a current pulse waveform 2

1 0.012A LOW Measures the low level of a current pulse waveform 2

1 0.210A RMS Measures the rms current 2

1 12.000V DC:DVM Measures the dc voltage on the DVM input 3

1 12.000V RMS:DVM Measures the rms voltage on the DVM input 3

1 VOLT 12.000

2 VOLT 2.000 Sets the voltage of output 1 on all models

Sets the voltage of output 2 4

1 CURR 2.000

2 CURR 1.000 Sets the current limit of output 1 on all models

Sets the current limit of output 2 4

Not available

OVERCURRENT Protection status (example shows overcurrent tripped)

*RST Places the dc source in the factory-default state

COUPLING ALL Couples or decouples output 1 and output 2 (NONE or ALL) 3

TYPE:CAP LOW Sets the output capacitance compensation (HIGH, H2, or LOW)

PON:STATE RST Select the power-on state command (RST or RCL0)

PROT:DLY 0.08 Sets the output protection delay in seconds

RI LATCHING Sets the remote inhibit mode (LATCHING, LIVE, or OFF)

DFI OFF Sets the discrete fault indicator state (ON or OFF)

DFI:SOUR OFF Selects the DFI source (QUES, OPER, ESB, RQS, or OFF )

PORT RIDFI Sets the output port functions (RIDFI or DIGIO)

DIGIO 7 Sets and reads the I/O port value (0 through 7)

SENSE:PROT OFF Enables or disables the open sense lead detect circuit (ON or OFF)

1 REL:MODE DD Sets the relay mode for Option 521 units (DD, HD, DH, or HH) (output 1 shown)

VOLT:PROT 22 Sets the overvoltage protection level

PROT:STAT ON Enables or disables overvoltage protection (ON or OFF)

CURR:RANG HIGH Sets the current range (HIGH, LOW, or AUTO) 2

CURR:DET ACDC Sets the current measurement detector (ACDC or DC) 2

TINT 46.8 Sets the time interval for a front panel measurement in seconds

POINT 2048 Sets the buffer size for a front panel measurement

CAL ON Accesses calibration menu (See Appendix B).

Use and to select parameters (table shows factory defaults). Use to exit any menu.

1Not valid for Agilent Model 66309B 2Not valid for Agilent Model 66111A

3Only valid for Agilent Model 66309B/D 4Only valid for Agilent Model 66311D/66309D

Address

Recall

Save

Shift

Error

Shift

Meter

Channel

Shift

Voltage

Protect

Current

Output

Res

Shift

Input

Cal

Shift

Meter