American Power Conversion 3-in-1 Wireless Mobile Router guide

	The Ethernet (WAN) Port Status

Connection Log	The Connection Log shows status messages relating to the existing connection.
	The most common messages are listed in the section “The following table describes the Connection
	Log Messages..”
	The Clear Log button will restart the log, while the Refresh button will update the messages shown on
	screen.
Buttons
Clear Log	Deletes all data currently in the log, making it easier to read new messages.
Connect	If not connected, establishes a connection to the ISP.
Disconnect	If connected to the ISP, hangs up the connection.
Refresh	Updates the data on screen.

The following table describes the Connection Log Messages.

Message	Description
Connect on Demand	Connection attempt has been triggered by the Connect automatically, as required setting.
Manual connection	Connection attempt started by the Connect button.
Reset physical connection	Preparing line for connection attempt.
Connecting to remote	Attempting to connect to the ISP's server.
server

Remote Server located	ISP's server has responded to connection attempt.
Start PPP	Attempting to log in to ISP's Server and establish a PPP connection.
PPP up successfully	Able to login to ISP's server and establish a PPP connection.
Idle time-out reached	The connection has been idle for the time period specified in the Idle Time-outfield. The
	connection will now be terminated.
Disconnecting	The current connection is being terminated, due to either the Idle Time-outabove, or
	Disconnect button being clicked.
Error: Remote Server not	ISP's server did not respond. This could be a server problem, or a problem with the link to the
found	server.

Error: PPP Connection	Unable to establish a PPP connection with the ISP's server. This could be a login problem
failed	(name or password) or a server problem.

Error: Connection to	The existing connection has been lost. This could be caused by a power failure, a link failure,
Server lost	or server failure.

Error: Invalid or	The data received from the ISP's server could not be processed. This could be caused by data
unknown packet type	corruption (from a bad link), or the server using a protocol which is not supported by this
	device.

4-13

Image 39

American Power Conversion 3-in-1 Wireless Mobile Router user manual Message Description

Contents

User’s Manual Page Contents Operation and Usage Configuring the Router for AP/Router ModeAP/Router Mode Advanced Features Configuring the Router for Client Mode Appendix A. Troubleshooting and Maintenance A-1 List of Figures Conventions and Typefaces Used in This Manual Contents of this ManualPreface Intended Audience Trademarks Regulatory ApprovalsCompliance Statement Disclaimers Introduction FeaturesWireless Router Mode Features Physical Features Package Contents Modes Feature Functionality AP/Router Mode Access Point AP Mode Client Mode Config Mode Modes Initial Configuration How to Perform the Initial ConfigurationRequirements Mode Configuration Screen Admin Using The System Setup Screen System Using The Config File Screen Upgrading the Firmware Upgrade Firmware Screen Upgrading the Firmware Connecting the Router to a Wired or Wireless Network Configuring the Router for Access Point AP Mode Using the Wireless Security Screen Wireless Wireless Security WEP Screen Wireless Security WPA-PSK Screen Using the Trusted Wireless Stations Screen Edit AddClear Using the Trusted Wireless Stations Screen Connecting in AP/Router Mode Configuring the Router for AP/Router Mode AP/Router Setup Screen Using the AP/Router Setup Screen Ethernet WAN Port Wireless LAN Security System WEP Wireless Security Screen Security System WPA-PSK Buttons Trusted Wireless Stations Screen IP Address Ethernet WAN Port Configuration ScreenConnection Type Travel Mode Hotel Connection Type Connection Types PPPoE, PPTP, L2TP, and No Login MAC AddressIdentification Connection Behavior Ethernet Port Configuration All Settings Ethernet WAN Port Configuration Screen Ethernet WAN Port Status InternetFixed/Dynamic IP Address Connection Log Connection Message Description Pptp Status Screen Pptp Status L2TP Status Screen Connection Status L2TP Screen Ethernet WAN Port Status Communication Applications AP/Router Mode Advanced FeaturesAdvanced Internet Screen Communication Applications My PC is not listed Enable DMZ usingPort Forwarding Send Application’s incoming calls to Port Forwarding IP Address Seen by Internet Users Service Port Forwarding ScreenProperties Modify Edit a Server Using Self-defined ServersConnecting to User-defined Servers Create a new Server Ddns Screen Using Dynamic DNS Domain Name Server Ddns Data Ddns Service Network Diagnostics Screen PingDNS Lookup Options Screen Backup DNSBackup DNS IP Enable UPnP Services Advanced PC Database Screen Advanced PC Database Screen PC Properties Security Screen FirewallOptions Allow L2TP Allow Pptp Security Screen Connecting the Computer to the Router Configuring the Router for Client Mode Client Mode Setup Screen Wireless ProfilesSet as Current Network Type Wireless Client Profile ScreenGeneral Profile Name Security Sytem Security When Changing Modes Using AP ModeOperation and Usage Connecting in AP/Router Mode Using AP/Router Mode AP/Router Setup Screen annotated Using Client Mode Solution Appendix a Troubleshooting and MaintenanceGeneral Problems Wireless Access AP or AP/Router Mode Problem 3 The wireless connections speed is very slow Router Mode Appendix B About Wireless LANs Modes for Wireless LANsBasic Service Set BSS and Extended Service Set ESS Wired Equivalent Privacy WEP Off, 64 Bit, 128 BitOpen System or Shared Key Wireless Interface Specifications Appendix C Specifications Technical Support Warranty