Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 9A000 C.3.2 ESA-200PC Technical Speciﬁcations, C-21, Hardware Specifications

Models: 9A000

1 180

Download 180 pages 32.99 Kb

Page 147

C.3.2 ESA-200PC Technical Speciﬁcations

Hardware Specifications

C.3.2 ESA-200PC Technical Speciﬁcations

The ESA-200PC ATM Adapter provides ATM connectivity to EISA-based PCs and servers, and has the following speciﬁcations:

	Hardware

Architecture	On-board 25 Mhz i960 RISC processor

AAL Support	Special-purpose hardware for AAL5 and AAL3/4, HEC, and CRC
	calculations

UNI	100 Mbps TAXI (4B/5B encoding);
	155Mbps OC-3/SONET STS-3c/SDH STM-1

Form Factor	Single-slot EISA bus, half-card

Compliance	ATM cell processing per ANSI T1S1.5/92-002R3, ITU I.361, and
	ATM Forum v3.0 UNI speciﬁcation

Cabling	Duplex 62.5/125 ∝m multimode ﬁber (2 km max. run, 10 dB loss);
	2-pair 100 ohm CAT 5, or CAT 5 screened, UTP (100 meters max.)

Connectors	ST and SC Types for multimode ﬁber; RJ-45 for CAT 5 UTP copper

	Software

Transparent standard protocol interface NDIS 3.0, ODI Server

SPANS Switched Virtual Circuits (SVCs) signaling protocol

Permanent Virtual Circuits (PVCs)

Supports up to 1024 Virtual Circuit Identiﬁers (VCIs)

Support for UNI 3.0 signalling

Support for LAN Emulation Clients

	General

Dimensions	H: 0.6" x W: 5.0" x D: 9.4" (1.5 cm x 12.7 cm x 23.8 cm)

Weight	8.3 oz (235 g)

Power Requirements	2 amps (maximum) @ +5V

Operating Temperature	32˚F to 104˚F (0˚C to 40˚C)

Operating Humidity	20% to 80% non-condensing @ 40˚C

Compliance	FCC Part 15, Class A Veriﬁcation and UL 1950

C-21

Image 147

Cabletron Systems 9A000 manual C.3.2 ESA-200PC Technical Speciﬁcations, C-21, Hardware Specifications

Contents

MMAC-Plus 9A000, SFCS-200BX SFCS-200WG and SFCS-1000 ATM SWITCH User’s GuidePage Copyright April 1996 by Cabletron Systems, Inc 35 Industrial Way VCCI Notice FCC NoticePreface Table of ContentsInstalling the 9A000 Switch HardwareChapter Switch SetupHardware Maintenance Procedures ContentsTroubleshooting Software Upgrade InstructionsAppendix A Appendix BAppendix C Hardware SpeciﬁcationsContents PREFACE Technical SupportTypographical Styles Are all four conditions true? Important Information IndicatorsPREFACE viiiInformation contained in NOTE statements has been found important enough to be called to the special attention of the operator and will be set off from the text as follows PREFACEPREFACE Laser WarningPREFACE Safety Agency ComplianceSafety Precautions SymbolsPREFACE Placement of a Cabletron Systems ProductPower Cord Connection Modiﬁcations to EquipmentCHAPTER Introduction1.1 Overview of the ATM Standard Introduction 1.2 Hardware DescriptionIntroduction Figure 1.1 - 9A000 Switch ConﬁgurationIntroduction 1.2.3 9A000 and SFCS Series Switch Board1.2.1 Front Panel Description 1.2.2 9A000 and SFCS Series Hardware ConﬁgurationIntroduction 1.2.4 Switch Control Processor1.2.5 9A000 and SFCS Series Network Modules 1.2.6 Environmental InformationIntroduction Features1.2.7 Standards Compliance 1.2.8 Safety Compliance1.3.1 Switch Control Software 1.3 Software DescriptionIntroduction 1-8 Installing the 9A000 2.1 Installing the 9A000CHAPTER Figure 2.1 - Installing the 9A000 Module Installing the 9A000Jack for ESD wrist strap Metal Back-Panel Circuit Card Card Guides Ensure that the circuit card is between the card guidesInstalling the 9A000 2.2 The Reset SwitchInstalling the 9A000 2-4 CHAPTER Switch HardwareSwitch Hardware 3.1 Switch Hardware ConﬁgurationsFigure 3.2 - SFCS-200BX Switch Conﬁguration Switch HardwareSFCS Switch Hardware48V DC AC Volt. InSwitch Hardware 3.2 Switch Hardware Components3.2.1 Switch Board 3.2.2 Switch Control Processor3.2.2.1.2 RS-232 Serial Port Switch Hardware3.2.2.1 i960 Switch Control Processor 3.2.2.1.1 RESET ButtonPin Number Switch HardwareSignal Signal Name3.2.2.1.6 SELECT Pushbutton Switch Hardware3.2.2.1.4 CTL Port 3.2.2.1.5 NEXT PushbuttonLED Color 3.2.3 Network ModulesSwitch Hardware 3.2.2.1.8 Power LEDSwitch Hardware 3-103.2.4.1 SFCS-200BX AC Power Supply 3.2.4 Power Supply Modules3-11 Switch HardwareThe model A AC power supply for an SFCS-1000 is shown in Figure 3-12Switch Hardware 3.2.4.2 SFCS-1000 AC Power Supply Model A3.2.4.2.2 Shutdown Conditions 3-13Switch Hardware 3.2.4.2.1 Power Supply LEDs3-14 Switch HardwareIf a model A power supply goes into shutdown, it will remain shut down until the power switch is turned off and turned on again power cycle. The power switch must remain off long enough for the SHUTDOWN LED to extinguish this allows the capacitors to discharge The model B AC power supply for an SFCS-1000 is shown in Figure 3-15Switch Hardware 3.2.4.3 SFCS-1000 AC Power Supply Model B3.2.4.3.2 Shutdown Conditions 3-16Switch Hardware 3.2.4.3.1 Power Supply LEDsSwitch Hardware 3-17Switch Hardware 3.2.6 SFCS-1000 Temperature Sensing3.2.5 SFCS-1000 Fan Tray 3-18AL1AL2 3.2.7 SFCS-1000 Common Equipment Card CEC3-19 Switch HardwarePins 3 and 3-20Switch Hardware Pins 1 and3.2.7.3 CEC Status LEDs 3-21Switch Hardware 3.2.7.3.1 Alarm LEDs3.2.7.3.3 Switch Board LEDs 3-22Switch Hardware 3.2.7.3.2 Power Supply LEDsMeaning 3-23Switch Hardware LED ColorSwitch Hardware 3-24 CHAPTER Switch Setup4.1 Introduction 4.2 Unpacking4.2.1 Inventorying the Unit Switch SetupSwitch Setup 4.3 Electrical Considerations4.4 Rack-Mounting an SFCS-200BX 4.4.1 Required ToolsSwitch Setup Switch Setup 4.4.2 Installing the Rack-mount BracketsNOTE The SFCS-200BX is an operational ATM switch at this point if used with other Cabletron switches or with ATM interface cards. However, if other vendor equipment is connected, you may have to complete an ini- tial user conﬁguration Switch Setup4.5 Rack-Mounting an SFCS-200WG 4.5.1 Required ToolsSwitch Setup Switch Setup 4.5.2 Installing the Rack-mount BracketsSwitch Setup 4.6 Rack-Mounting an SFCS-1000 4-10Switch Setup 4.6.1 Installing the SFCS-1000 4-11Switch Setup 4.7 Installing the Serial Cable 4-12Switch Setup Switch Setup 4.8 Modem Conﬁguration4.8.1 Modem Parameters 4-134-14 4.9 Conﬁguring IP Addressesconﬁguration ip address interface address conﬁguration ip mask interface maskSwitch Setup 4.10 AMI Security4.11 Subsequent Operation 4-154-16 4.12 Verifying the Installation4.13 Product Registration Information conﬁguration port showCHAPTER Hardware Maintenance Procedures5.1 Network Module Replacement 5.1.1 OverviewHardware Maintenance Procedures 5.1.2 Multicast ModeHardware Maintenance Procedures 5.1.3 Hot-swapping Network Modules5.2 Power Supply Module Replacement 5.2.1 SFCS-200BX Power Supply Module ReplacementHardware Maintenance Procedures 5. Pull forward on the handle to remove the sliding tray Hardware Maintenance ProceduresAC 48V DC 5VDC OK SHUTDOWN 5.2.2 SFCS-1000 Power Supply Module ReplacementHardware Maintenance Procedures 5.2.2.1 Replacing an SFCS-1000 AC Power Supply Model A3. Unplug and remove the power cord from the failed supply Hardware Maintenance Procedures7. Ensure that the fuses on the new unit are rated at 12.5A Hardware Maintenance ProceduresON/OFF Switch Handle Hardware Maintenance Procedures5.2.2.2 Replacing an SFCS-1000 AC Power Supply Model B A model B AC power supply module for an SFCS-1000 is shown in FigureHardware Maintenance Procedures 5-105-11 Hardware Maintenance Procedures6. Set the failed supply aside and prepare to install the new one 5.3 SFCS-1000 Fan Tray Replacement 5-12Hardware Maintenance Procedures 5.4 Switch Control Processor Replacement 5-13Hardware Maintenance Procedures 5-14 Hardware Maintenance ProceduresCAUTION Take care to properly align the SCP in the card guides in the following step 5.5 Switch Board Replacement 5-15Hardware Maintenance Procedures 5-16 Hardware Maintenance ProceduresNOTE To ensure that the switch will work with the previously established network conﬁguration, the relative position of the network modules must not change when you transfer them to the new fabric. For example, an OC-3c network module that is removed from slot A of the old switch fabric must be installed in slot A of the new switch fabric. Therefore, it is recommended that you label all network connections and network modules before removing them 5-17 Hardware Maintenance ProceduresCAUTION Make sure the replacement board is properly aligned in the slot in the next step Hardware Maintenance Procedures 5-18 CHAPTER Software Upgrade Instructionseject device 6.1 Obtaining the Software Upgrade File via DisketteSoftware Upgrade Instructions tar -xvf deviceSoftware Upgrade Instructions foreextract deviceoperation upgrade ? 6.2 Performing the Software Upgrademkdir /tftpboot mv ﬁlename /tftpbootoperation upgrade 169.144.3.54asx-scp4.0.01.3 operation upgrade 169.144.3.54ASX-200BX4.0.01.3Software Upgrade Instructions Reboot the switchy? y Software Upgrade InstructionsSoftware Upgrade Instructions 6.3 Changing between Multiple Versions of SoftwareSoftware Upgrade Instructions localhostoperation rebootAre you sure you want to reboot this switch n? y Software Upgrade Instructions 6.4 Using bootp to Download Software to the Switch6.4.2 Setting Up Your bootp Server 6.4.1 Overview6.4.3 Adding an Entry for Your Switch in the bootptab File 6-10Software Upgrade Instructions 6-11 Software Upgrade InstructionsThe variables in the previous example are deﬁned as follows 6.4.4 Setting Up a tftpboot Server 6-12Software Upgrade Instructions Troubleshooting A.1 Adapter Hardware TroubleshootingAPPENDIX A Figure A.1 - Adapter Hardware Troubleshooting Flowchart TroubleshootingTroubleshooting A.1.1 Run LooptestA.1.2 Check Self-Test Automatically Performed A.1.3 Firmware Download Automatically PerformedTroubleshooting A.1.4 Hardware Detected by Driver netstatTroubleshooting A.1.5 Check Firmware atmstat fa0Troubleshooting Troubleshooting A.1.6 Check Physical LinkTroubleshooting A.2 Testing Network Connectivity Using PVCsFigure A ping IPaddressofremoteworkstation A-10Troubleshooting A.2.1 Verifying the Outgoing ATM ARP Entry A-11Troubleshooting A.2.2 atmstat A-12Troubleshooting A.2.2.3 Cells and AAL* Errors Received by Remote A-13Troubleshooting A.2.2.2 Cells and VPI/VCI Errors Received by RemoteA-14 TroubleshootingA.2.2.5 Cells and No Errors Received by Remote and Transmitting Cells A-15 A.3 Collecting Additional InformationA.3.1 Basic Information A.3.2 Adapter InformationA-16 uname -aifconﬁg fa0 netstat -nrTroubleshooting netstat -inadinfo fa0 A-17A.3.3 Switch Information A-18Troubleshooting Troubleshooting asxmon switchnamecport switchname A-19Troubleshooting conﬁguration spans showconﬁguration port show A-20Troubleshooting conﬁguration port taxi showconﬁguration port ds3 show A-21conﬁguration port e3 show conﬁguration port ds1 showconﬁguration port sonet show conﬁguration e1 showSCP Diagnostics B.1 SFCS-200WG, SFCS-200BX, SFCS-1000 DiagnosticsAPPENDIX B SCP Diagnostics B.1.1 Accessing the Monitor ModeSCP Diagnostics B.1.2.2 DRAM Test B.1.2 Running the Hardware TestsSCP Diagnostics B.1.2.1 Clock TestB.1.2.5 FLASH Test SCP DiagnosticsB.1.2.3 DRAM Chip Test B.1.2.4 Ethernet TestSCP Diagnostics B.1.2.6 FLASH Chip Test=test-fc 1 Save Chip Clock OK DRAM OK Ethernet OK Timer OK Serial OK SCP DiagnosticsB.1.2.9 Timer Test Timer OKSCP Diagnostics =test-manufact Clock OK DRAM OK Ethernet OK Timer OKB.1.2.11 Complete Hardware Test C.1 Cabletron ATM Switches APPENDIX CHardware Speciﬁcations C.1.1 SFCS-200WG Hardware SpecificationsHardware Specifications C.1.2 SFCS-200BXHardware Specifications C.1.3 SFCS-1000C.2 ATM Network Modules C.2.1 100 Mbps TAXI ModuleHardware Specifications Hardware Specifications C.2.2 155 Mbps OC-3c/STM-1 MM ModuleHardware Specifications C.2.3 155 Mbps STS-3c/STM-1 UTP ModuleC.2.3.2 Connecting Switches with 155 Mbps UTP Network Modules Hardware SpecificationsSignal Signal NameHardware Specifications C.2.4 622 Mbps OC-12c/STM-4c MM ModuleC.2.5 25 Mbps TP25 Module C-10Hardware Specifications C-11 Hardware SpecificationsC.2.5.1 Connecting Switches with TP25 Network Modules Hardware Specifications C-12C.2.6 34 Mbps E3 Module C-13Hardware Specifications C.2.7 45 Mbps DS3 Module C-14Hardware Specifications C.2.8 155 Mbps OC-3c/STM-1 SM Module C-15Hardware Specifications C.2.9 155 Mbps OC-3c/STM-1 3MM/1SM Module C-16Hardware Specifications C-17 Hardware SpecificationsDescription C.2.10 622 Mbps OC-12c/STM-4c SM Module C-18Hardware Specifications Hardware Specifications C.3 ATM AdaptersC.3.1 Adapter Cabling Speciﬁcations C-19C-20 Hardware SpecificationsC.3.1.2 UTP Cable Speciﬁcations C.3.2 ESA-200PC Technical Speciﬁcations C-21Hardware Specifications C.3.3 PCA-200PC Technical Speciﬁcations C-22Hardware Specifications C.3.4 PCA-200MAC Technical Speciﬁcations C-23Hardware Specifications C.3.5 NBA-200 Technical Speciﬁcations C-24Hardware Specifications C.3.6 GIA-200 Technical Speciﬁcations C-25Hardware Specifications C.3.7 HPA-200 Technical Speciﬁcations C-26Hardware Specifications C.3.8 MCA-200 Technical Speciﬁcations C-27Hardware Specifications C.3.9 SBA-200 Technical Speciﬁcations C-28Hardware Specifications C.3.10 ESA-200 Technical Speciﬁcations C-29Hardware Specifications C.3.11 VMA-200 Technical Speciﬁcations C-30Hardware Specifications Hardware Specifications C-31 Hardware Specifications C-32 GLOSSARY ATM Link - a virtual path link VPL or a virtual channel link VCL GLOSSARYGLOSSARY atmconﬁg - a FORE program used to enable or disable SPANS signallingCell - an ATM Layer protocol data unit PDU GLOSSARYCell Header - ATM Layer protocol control information GLOSSARYDSn Digital Standard n 0, 1, 1C, 2, and 3 - a method that deﬁnes the rate and format of digital hierarchy GLOSSARYEPROM - Erasable Programmable Read Only Memory See PROM GLOSSARYHPUX - the Hewlett-Packard version of UNIX GLOSSARYnnn.nnn.nnn.nnn GLOSSARYGLOSSARY g-10g-11 GLOSSARYLayer Entity - an active layer within an element GLOSSARY g-12g-13 GLOSSARYOpenView - Hewlett-Packard’s network management software g-14 GLOSSARYPeer Entities - entities within the same layer g-15 GLOSSARYPoint-to-Point Connection - a connection with only two endpoints g-16 GLOSSARYPVC Permanent Virtual Circuit or Channel - a circuit or channel through an ATM network provisioned by a carrier between two endpoints used for dedicated long-term information transport between locations g-17 GLOSSARYSGMP Simple Gateway Management Protocol - the predecessor to SNMP g-18 STS Synchronous Transport Signal - a SONET electrical signal rateGLOSSARY g-19 Switched Connection - a connection established via signallingGLOSSARY g-20 GLOSSARYVCI Virtual Channel Identiﬁer - the address or label of a VC g-21 GLOSSARYVPI Virtual Path Identiﬁer - the address or label of a particular VP GLOSSARY g-22