Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 9A000 manual Switch Hardware Conﬁgurations

Models: 9A000

1 180

Download 180 pages 32.99 Kb

Page 28

Switch Hardware

Switch Hardware

3.1Switch Hardware Conﬁgurations

The SFCS-200WG, as shown in Figure 3.1, is a self-contained ATM switch that provides an Ethernet connection for network management access. The SFCS-200WG ATM switch hardware consists of a single switch board with an i960 SCP, network modules, and fans. These components work together to provide ATM switching capabilities, as well as distributed connection setup and management.

SYSTEMS

SecureFast SFCS-200WG

								5 VOLT
	RX1	RX2	RX3	RX4	RX1	RX2	RX3	RX4
	TX1	TX2	TX3	TX4	TX1	TX2	TX3	TX4
	RX1	RX2	RX3	RX4	RX1	RX2	RX3	RX4
	TX1	TX2	TX3	TX4	TX1	TX2	TX3	TX4
	Tx	Rx		PWR	Tx	Rx		PWR
	C	L		PWR	Tx	Rx		PWR
RESET				RESET	C	L		-
								-

SER

ETH

NEXT

SELECT

SER

ETH

NEXT SELECT

Figure 3.1 - SFCS-200WG Switch Conﬁguration

The SFCS-200BX, as shown in Figure 3.2, is a self-contained ATM switch that provides an Ethernet connection for network management access. The SFCS-200BX hardware consists of a single switch board with an i960 SCP, net- work modules, redundant power supplies, and fans. These components work together to provide ATM switching capabilities, as well as distributed connec- tion setup and management.

3-2

Image 28

Cabletron Systems 9A000 manual Switch Hardware Conﬁgurations

Contents

SFCS-200WG and SFCS-1000 ATM SWITCH User’s Guide MMAC-Plus 9A000, SFCS-200BXPage Copyright April 1996 by Cabletron Systems, Inc 35 Industrial Way FCC Notice VCCI NoticeTable of Contents Installing the 9A000Switch Hardware PrefaceSwitch Setup Hardware Maintenance ProceduresContents ChapterSoftware Upgrade Instructions Appendix AAppendix B TroubleshootingHardware Speciﬁcations Appendix CContents Technical Support PREFACETypographical Styles Important Information Indicators PREFACEviii Are all four conditions true?PREFACE Information contained in NOTE statements has been found important enough to be called to the special attention of the operator and will be set off from the text as followsLaser Warning PREFACESafety Agency Compliance Safety PrecautionsSymbols PREFACEPlacement of a Cabletron Systems Product Power Cord ConnectionModiﬁcations to Equipment PREFACEIntroduction CHAPTER1.1 Overview of the ATM Standard 1.2 Hardware Description IntroductionFigure 1.1 - 9A000 Switch Conﬁguration Introduction1.2.3 9A000 and SFCS Series Switch Board 1.2.1 Front Panel Description1.2.2 9A000 and SFCS Series Hardware Conﬁguration Introduction1.2.4 Switch Control Processor 1.2.5 9A000 and SFCS Series Network Modules1.2.6 Environmental Information IntroductionFeatures Introduction1.2.8 Safety Compliance 1.3.1 Switch Control Software1.3 Software Description 1.2.7 Standards ComplianceIntroduction 1-8 2.1 Installing the 9A000 Installing the 9A000CHAPTER Installing the 9A000 Jack for ESD wrist strap Metal Back-Panel Circuit Card Card GuidesEnsure that the circuit card is between the card guides Figure 2.1 - Installing the 9A000 Module2.2 The Reset Switch Installing the 9A000Installing the 9A000 2-4 Switch Hardware CHAPTER3.1 Switch Hardware Conﬁgurations Switch HardwareSwitch Hardware Figure 3.2 - SFCS-200BX Switch ConﬁgurationSwitch Hardware 48V DCAC Volt. In SFCS3.2 Switch Hardware Components 3.2.1 Switch Board3.2.2 Switch Control Processor Switch HardwareSwitch Hardware 3.2.2.1 i960 Switch Control Processor3.2.2.1.1 RESET Button 3.2.2.1.2 RS-232 Serial PortSwitch Hardware SignalSignal Name Pin NumberSwitch Hardware 3.2.2.1.4 CTL Port3.2.2.1.5 NEXT Pushbutton 3.2.2.1.6 SELECT Pushbutton3.2.3 Network Modules Switch Hardware3.2.2.1.8 Power LED LED Color3-10 Switch Hardware3.2.4 Power Supply Modules 3-11Switch Hardware 3.2.4.1 SFCS-200BX AC Power Supply3-12 Switch Hardware3.2.4.2 SFCS-1000 AC Power Supply Model A The model A AC power supply for an SFCS-1000 is shown in Figure3-13 Switch Hardware3.2.4.2.1 Power Supply LEDs 3.2.4.2.2 Shutdown ConditionsSwitch Hardware 3-14If a model A power supply goes into shutdown, it will remain shut down until the power switch is turned off and turned on again power cycle. The power switch must remain off long enough for the SHUTDOWN LED to extinguish this allows the capacitors to discharge 3-15 Switch Hardware3.2.4.3 SFCS-1000 AC Power Supply Model B The model B AC power supply for an SFCS-1000 is shown in Figure3-16 Switch Hardware3.2.4.3.1 Power Supply LEDs 3.2.4.3.2 Shutdown Conditions3-17 Switch Hardware3.2.6 SFCS-1000 Temperature Sensing 3.2.5 SFCS-1000 Fan Tray3-18 Switch Hardware3.2.7 SFCS-1000 Common Equipment Card CEC 3-19Switch Hardware AL1AL23-20 Switch HardwarePins 1 and Pins 3 and3-21 Switch Hardware3.2.7.3.1 Alarm LEDs 3.2.7.3 CEC Status LEDs3-22 Switch Hardware3.2.7.3.2 Power Supply LEDs 3.2.7.3.3 Switch Board LEDs3-23 Switch HardwareLED Color MeaningSwitch Hardware 3-24 Switch Setup 4.1 Introduction4.2 Unpacking CHAPTERSwitch Setup 4.2.1 Inventorying the Unit4.3 Electrical Considerations Switch Setup4.4.1 Required Tools 4.4 Rack-Mounting an SFCS-200BXSwitch Setup 4.4.2 Installing the Rack-mount Brackets Switch SetupSwitch Setup NOTE The SFCS-200BX is an operational ATM switch at this point if used with other Cabletron switches or with ATM interface cards. However, if other vendor equipment is connected, you may have to complete an ini- tial user conﬁguration4.5.1 Required Tools 4.5 Rack-Mounting an SFCS-200WGSwitch Setup 4.5.2 Installing the Rack-mount Brackets Switch SetupSwitch Setup 4-10 4.6 Rack-Mounting an SFCS-1000Switch Setup 4-11 4.6.1 Installing the SFCS-1000Switch Setup 4-12 4.7 Installing the Serial CableSwitch Setup 4.8 Modem Conﬁguration 4.8.1 Modem Parameters4-13 Switch Setup4.9 Conﬁguring IP Addresses conﬁguration ip address interface addressconﬁguration ip mask interface mask 4-144.10 AMI Security 4.11 Subsequent Operation4-15 Switch Setup4.12 Verifying the Installation 4.13 Product Registration Informationconﬁguration port show 4-16Hardware Maintenance Procedures 5.1 Network Module Replacement5.1.1 Overview CHAPTER5.1.2 Multicast Mode Hardware Maintenance Procedures5.1.3 Hot-swapping Network Modules Hardware Maintenance Procedures5.2.1 SFCS-200BX Power Supply Module Replacement 5.2 Power Supply Module ReplacementHardware Maintenance Procedures Hardware Maintenance Procedures 5. Pull forward on the handle to remove the sliding tray5.2.2 SFCS-1000 Power Supply Module Replacement Hardware Maintenance Procedures5.2.2.1 Replacing an SFCS-1000 AC Power Supply Model A AC 48V DC 5VDC OK SHUTDOWNHardware Maintenance Procedures 3. Unplug and remove the power cord from the failed supplyHardware Maintenance Procedures 7. Ensure that the fuses on the new unit are rated at 12.5AHardware Maintenance Procedures 5.2.2.2 Replacing an SFCS-1000 AC Power Supply Model BA model B AC power supply module for an SFCS-1000 is shown in Figure ON/OFF Switch Handle5-10 Hardware Maintenance ProceduresHardware Maintenance Procedures 5-116. Set the failed supply aside and prepare to install the new one 5-12 5.3 SFCS-1000 Fan Tray ReplacementHardware Maintenance Procedures 5-13 5.4 Switch Control Processor ReplacementHardware Maintenance Procedures Hardware Maintenance Procedures 5-14CAUTION Take care to properly align the SCP in the card guides in the following step 5-15 5.5 Switch Board ReplacementHardware Maintenance Procedures Hardware Maintenance Procedures 5-16NOTE To ensure that the switch will work with the previously established network conﬁguration, the relative position of the network modules must not change when you transfer them to the new fabric. For example, an OC-3c network module that is removed from slot A of the old switch fabric must be installed in slot A of the new switch fabric. Therefore, it is recommended that you label all network connections and network modules before removing them Hardware Maintenance Procedures 5-17CAUTION Make sure the replacement board is properly aligned in the slot in the next step Hardware Maintenance Procedures 5-18 Software Upgrade Instructions CHAPTER6.1 Obtaining the Software Upgrade File via Diskette Software Upgrade Instructionstar -xvf device eject deviceforeextract device Software Upgrade Instructions6.2 Performing the Software Upgrade mkdir /tftpbootmv ﬁlename /tftpboot operation upgrade ?operation upgrade 169.144.3.54ASX-200BX4.0.01.3 operation upgrade 169.144.3.54asx-scp4.0.01.3Software Upgrade Instructions Software Upgrade Instructions Reboot the switchy? y6.3 Changing between Multiple Versions of Software Software Upgrade Instructionslocalhostoperation reboot Software Upgrade InstructionsAre you sure you want to reboot this switch n? y 6.4 Using bootp to Download Software to the Switch 6.4.2 Setting Up Your bootp Server6.4.1 Overview Software Upgrade Instructions6-10 6.4.3 Adding an Entry for Your Switch in the bootptab FileSoftware Upgrade Instructions Software Upgrade Instructions 6-11The variables in the previous example are deﬁned as follows 6-12 6.4.4 Setting Up a tftpboot ServerSoftware Upgrade Instructions A.1 Adapter Hardware Troubleshooting TroubleshootingAPPENDIX A Troubleshooting Figure A.1 - Adapter Hardware Troubleshooting FlowchartA.1.1 Run Looptest TroubleshootingA.1.3 Firmware Download Automatically Performed A.1.2 Check Self-Test Automatically PerformedTroubleshooting netstat A.1.4 Hardware Detected by DriverTroubleshooting atmstat fa0 A.1.5 Check FirmwareTroubleshooting A.1.6 Check Physical Link TroubleshootingA.2 Testing Network Connectivity Using PVCs TroubleshootingFigure A A-10 ping IPaddressofremoteworkstationTroubleshooting A-11 A.2.1 Verifying the Outgoing ATM ARP EntryTroubleshooting A-12 A.2.2 atmstatTroubleshooting A-13 TroubleshootingA.2.2.2 Cells and VPI/VCI Errors Received by Remote A.2.2.3 Cells and AAL* Errors Received by RemoteTroubleshooting A-14A.2.2.5 Cells and No Errors Received by Remote and Transmitting Cells A.3 Collecting Additional Information A.3.1 Basic InformationA.3.2 Adapter Information A-15uname -a ifconﬁg fa0netstat -nr A-16netstat -in adinfo fa0A-17 TroubleshootingA-18 A.3.3 Switch InformationTroubleshooting asxmon switchname cport switchnameA-19 Troubleshootingconﬁguration spans show conﬁguration port showA-20 Troubleshootingconﬁguration port taxi show conﬁguration port ds3 showA-21 Troubleshootingconﬁguration port ds1 show conﬁguration port sonet showconﬁguration e1 show conﬁguration port e3 showB.1 SFCS-200WG, SFCS-200BX, SFCS-1000 Diagnostics SCP DiagnosticsAPPENDIX B B.1.1 Accessing the Monitor Mode SCP DiagnosticsSCP Diagnostics B.1.2 Running the Hardware Tests SCP DiagnosticsB.1.2.1 Clock Test B.1.2.2 DRAM TestSCP Diagnostics B.1.2.3 DRAM Chip TestB.1.2.4 Ethernet Test B.1.2.5 FLASH TestB.1.2.6 FLASH Chip Test SCP Diagnostics=test-fc 1 Save Chip SCP Diagnostics B.1.2.9 Timer TestTimer OK Clock OK DRAM OK Ethernet OK Timer OK Serial OK=test-manufact Clock OK DRAM OK Ethernet OK Timer OK SCP DiagnosticsB.1.2.11 Complete Hardware Test APPENDIX C C.1 Cabletron ATM SwitchesHardware Speciﬁcations Hardware Specifications C.1.1 SFCS-200WGC.1.2 SFCS-200BX Hardware SpecificationsC.1.3 SFCS-1000 Hardware SpecificationsC.2.1 100 Mbps TAXI Module C.2 ATM Network ModulesHardware Specifications C.2.2 155 Mbps OC-3c/STM-1 MM Module Hardware SpecificationsC.2.3 155 Mbps STS-3c/STM-1 UTP Module Hardware SpecificationsHardware Specifications SignalSignal Name C.2.3.2 Connecting Switches with 155 Mbps UTP Network ModulesC.2.4 622 Mbps OC-12c/STM-4c MM Module Hardware SpecificationsC-10 C.2.5 25 Mbps TP25 ModuleHardware Specifications Hardware Specifications C-11C.2.5.1 Connecting Switches with TP25 Network Modules C-12 Hardware SpecificationsC-13 C.2.6 34 Mbps E3 ModuleHardware Specifications C-14 C.2.7 45 Mbps DS3 ModuleHardware Specifications C-15 C.2.8 155 Mbps OC-3c/STM-1 SM ModuleHardware Specifications C-16 C.2.9 155 Mbps OC-3c/STM-1 3MM/1SM ModuleHardware Specifications Hardware Specifications C-17Description C-18 C.2.10 622 Mbps OC-12c/STM-4c SM ModuleHardware Specifications C.3 ATM Adapters C.3.1 Adapter Cabling SpeciﬁcationsC-19 Hardware SpecificationsHardware Specifications C-20C.3.1.2 UTP Cable Speciﬁcations C-21 C.3.2 ESA-200PC Technical SpeciﬁcationsHardware Specifications C-22 C.3.3 PCA-200PC Technical SpeciﬁcationsHardware Specifications C-23 C.3.4 PCA-200MAC Technical SpeciﬁcationsHardware Specifications C-24 C.3.5 NBA-200 Technical SpeciﬁcationsHardware Specifications C-25 C.3.6 GIA-200 Technical SpeciﬁcationsHardware Specifications C-26 C.3.7 HPA-200 Technical SpeciﬁcationsHardware Specifications C-27 C.3.8 MCA-200 Technical SpeciﬁcationsHardware Specifications C-28 C.3.9 SBA-200 Technical SpeciﬁcationsHardware Specifications C-29 C.3.10 ESA-200 Technical SpeciﬁcationsHardware Specifications C-30 C.3.11 VMA-200 Technical SpeciﬁcationsHardware Specifications Hardware Specifications C-31 Hardware Specifications C-32 GLOSSARY GLOSSARY ATM Link - a virtual path link VPL or a virtual channel link VCLatmconﬁg - a FORE program used to enable or disable SPANS signalling GLOSSARYGLOSSARY Cell - an ATM Layer protocol data unit PDUGLOSSARY Cell Header - ATM Layer protocol control informationGLOSSARY DSn Digital Standard n 0, 1, 1C, 2, and 3 - a method that deﬁnes the rate and format of digital hierarchyGLOSSARY EPROM - Erasable Programmable Read Only Memory See PROMGLOSSARY HPUX - the Hewlett-Packard version of UNIXGLOSSARY nnn.nnn.nnn.nnng-10 GLOSSARYGLOSSARY g-11Layer Entity - an active layer within an element g-12 GLOSSARYGLOSSARY g-13OpenView - Hewlett-Packard’s network management software GLOSSARY g-14Peer Entities - entities within the same layer GLOSSARY g-15Point-to-Point Connection - a connection with only two endpoints GLOSSARY g-16PVC Permanent Virtual Circuit or Channel - a circuit or channel through an ATM network provisioned by a carrier between two endpoints used for dedicated long-term information transport between locations GLOSSARY g-17SGMP Simple Gateway Management Protocol - the predecessor to SNMP STS Synchronous Transport Signal - a SONET electrical signal rate g-18GLOSSARY Switched Connection - a connection established via signalling g-19GLOSSARY GLOSSARY g-20VCI Virtual Channel Identiﬁer - the address or label of a VC GLOSSARY g-21VPI Virtual Path Identiﬁer - the address or label of a particular VP GLOSSARY g-22