Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 9A000 manual C.3 ATM Adapters, C.3.1 Adapter Cabling Speciﬁcations, C-19

Models: 9A000

1 180

Download 180 pages 32.99 Kb

Page 145

Image 145

Hardware Specifications

C.3 ATM Adapters

The family of ATM adapters provides a ﬂexible ATM interface for the commu- nications needs of today’s high-speed workstations and personal computers.

C.3.1 Adapter Cabling Speciﬁcations

C.3.1.1 Fiber-Optic Cable Speciﬁcations

The table below lists the recommended cable speciﬁcations for all ATM adapt- ers that use ﬁber-optic cabling to ensure optimal adapter and switch perfor- mance:

Description	Speciﬁcation for Multimode Products

Core Diameter	62.5 ∝m

Fiber Diameter	125 ∝m

Wavelength	1310 nm

Loss Characteristic	~0.5 dB/km

Connector Style	SC or ST

Power Budget	11 dB *

Approximate Distance	2 km

Transmit Power	-19 dBm (minimum)

Receive Power	-30 dBm (minimum)

* If a 50 ∝m core ﬁber is used, the power budget is derated by 4 dB.

C-19

Page 145

Image 145

Cabletron Systems 9A000 manual C.3 ATM Adapters, C.3.1 Adapter Cabling Speciﬁcations, C-19, Hardware Specifications

Contents

MMAC-Plus 9A000, SFCS-200BX SFCS-200WG and SFCS-1000 ATM SWITCH User’s GuidePage Copyright April 1996 by Cabletron Systems, Inc 35 Industrial Way VCCI Notice FCC NoticeInstalling the 9A000 Table of ContentsSwitch Hardware PrefaceHardware Maintenance Procedures Switch SetupContents ChapterAppendix A Software Upgrade InstructionsAppendix B TroubleshootingHardware Speciﬁcations Appendix CContents Technical Support PREFACETypographical Styles PREFACE Important Information Indicatorsviii Are all four conditions true?Information contained in NOTE statements has been found important enough to be called to the special attention of the operator and will be set off from the text as follows PREFACEPREFACE Laser WarningSafety Precautions Safety Agency ComplianceSymbols PREFACEPower Cord Connection Placement of a Cabletron Systems ProductModiﬁcations to Equipment PREFACEIntroduction CHAPTER1.1 Overview of the ATM Standard Introduction 1.2 Hardware DescriptionIntroduction Figure 1.1 - 9A000 Switch Conﬁguration1.2.1 Front Panel Description 1.2.3 9A000 and SFCS Series Switch Board1.2.2 9A000 and SFCS Series Hardware Conﬁguration Introduction1.2.5 9A000 and SFCS Series Network Modules 1.2.4 Switch Control Processor1.2.6 Environmental Information IntroductionIntroduction Features1.3.1 Switch Control Software 1.2.8 Safety Compliance1.3 Software Description 1.2.7 Standards ComplianceIntroduction 1-8 2.1 Installing the 9A000 Installing the 9A000CHAPTER Jack for ESD wrist strap Metal Back-Panel Circuit Card Card Guides Installing the 9A000Ensure that the circuit card is between the card guides Figure 2.1 - Installing the 9A000 ModuleInstalling the 9A000 2.2 The Reset SwitchInstalling the 9A000 2-4 CHAPTER Switch HardwareSwitch Hardware 3.1 Switch Hardware ConﬁgurationsFigure 3.2 - SFCS-200BX Switch Conﬁguration Switch Hardware48V DC Switch HardwareAC Volt. In SFCS3.2.1 Switch Board 3.2 Switch Hardware Components3.2.2 Switch Control Processor Switch Hardware3.2.2.1 i960 Switch Control Processor Switch Hardware3.2.2.1.1 RESET Button 3.2.2.1.2 RS-232 Serial PortSignal Switch HardwareSignal Name Pin Number3.2.2.1.4 CTL Port Switch Hardware3.2.2.1.5 NEXT Pushbutton 3.2.2.1.6 SELECT PushbuttonSwitch Hardware 3.2.3 Network Modules3.2.2.1.8 Power LED LED ColorSwitch Hardware 3-103-11 3.2.4 Power Supply ModulesSwitch Hardware 3.2.4.1 SFCS-200BX AC Power SupplySwitch Hardware 3-123.2.4.2 SFCS-1000 AC Power Supply Model A The model A AC power supply for an SFCS-1000 is shown in FigureSwitch Hardware 3-133.2.4.2.1 Power Supply LEDs 3.2.4.2.2 Shutdown ConditionsSwitch Hardware 3-14If a model A power supply goes into shutdown, it will remain shut down until the power switch is turned off and turned on again power cycle. The power switch must remain off long enough for the SHUTDOWN LED to extinguish this allows the capacitors to discharge Switch Hardware 3-153.2.4.3 SFCS-1000 AC Power Supply Model B The model B AC power supply for an SFCS-1000 is shown in FigureSwitch Hardware 3-163.2.4.3.1 Power Supply LEDs 3.2.4.3.2 Shutdown ConditionsSwitch Hardware 3-173.2.5 SFCS-1000 Fan Tray 3.2.6 SFCS-1000 Temperature Sensing3-18 Switch Hardware3-19 3.2.7 SFCS-1000 Common Equipment Card CECSwitch Hardware AL1AL2Switch Hardware 3-20Pins 1 and Pins 3 andSwitch Hardware 3-213.2.7.3.1 Alarm LEDs 3.2.7.3 CEC Status LEDsSwitch Hardware 3-223.2.7.3.2 Power Supply LEDs 3.2.7.3.3 Switch Board LEDsSwitch Hardware 3-23LED Color MeaningSwitch Hardware 3-24 4.1 Introduction Switch Setup4.2 Unpacking CHAPTER4.2.1 Inventorying the Unit Switch SetupSwitch Setup 4.3 Electrical Considerations4.4.1 Required Tools 4.4 Rack-Mounting an SFCS-200BXSwitch Setup Switch Setup 4.4.2 Installing the Rack-mount BracketsNOTE The SFCS-200BX is an operational ATM switch at this point if used with other Cabletron switches or with ATM interface cards. However, if other vendor equipment is connected, you may have to complete an ini- tial user conﬁguration Switch Setup4.5.1 Required Tools 4.5 Rack-Mounting an SFCS-200WGSwitch Setup Switch Setup 4.5.2 Installing the Rack-mount BracketsSwitch Setup 4-10 4.6 Rack-Mounting an SFCS-1000Switch Setup 4-11 4.6.1 Installing the SFCS-1000Switch Setup 4-12 4.7 Installing the Serial CableSwitch Setup 4.8.1 Modem Parameters 4.8 Modem Conﬁguration4-13 Switch Setupconﬁguration ip address interface address 4.9 Conﬁguring IP Addressesconﬁguration ip mask interface mask 4-144.11 Subsequent Operation 4.10 AMI Security4-15 Switch Setup4.13 Product Registration Information 4.12 Verifying the Installationconﬁguration port show 4-165.1 Network Module Replacement Hardware Maintenance Procedures5.1.1 Overview CHAPTERHardware Maintenance Procedures 5.1.2 Multicast ModeHardware Maintenance Procedures 5.1.3 Hot-swapping Network Modules5.2.1 SFCS-200BX Power Supply Module Replacement 5.2 Power Supply Module ReplacementHardware Maintenance Procedures 5. Pull forward on the handle to remove the sliding tray Hardware Maintenance ProceduresHardware Maintenance Procedures 5.2.2 SFCS-1000 Power Supply Module Replacement5.2.2.1 Replacing an SFCS-1000 AC Power Supply Model A AC 48V DC 5VDC OK SHUTDOWN3. Unplug and remove the power cord from the failed supply Hardware Maintenance Procedures7. Ensure that the fuses on the new unit are rated at 12.5A Hardware Maintenance Procedures5.2.2.2 Replacing an SFCS-1000 AC Power Supply Model B Hardware Maintenance ProceduresA model B AC power supply module for an SFCS-1000 is shown in Figure ON/OFF Switch HandleHardware Maintenance Procedures 5-10Hardware Maintenance Procedures 5-116. Set the failed supply aside and prepare to install the new one 5-12 5.3 SFCS-1000 Fan Tray ReplacementHardware Maintenance Procedures 5-13 5.4 Switch Control Processor ReplacementHardware Maintenance Procedures Hardware Maintenance Procedures 5-14CAUTION Take care to properly align the SCP in the card guides in the following step 5-15 5.5 Switch Board ReplacementHardware Maintenance Procedures Hardware Maintenance Procedures 5-16NOTE To ensure that the switch will work with the previously established network conﬁguration, the relative position of the network modules must not change when you transfer them to the new fabric. For example, an OC-3c network module that is removed from slot A of the old switch fabric must be installed in slot A of the new switch fabric. Therefore, it is recommended that you label all network connections and network modules before removing them Hardware Maintenance Procedures 5-17CAUTION Make sure the replacement board is properly aligned in the slot in the next step Hardware Maintenance Procedures 5-18 CHAPTER Software Upgrade InstructionsSoftware Upgrade Instructions 6.1 Obtaining the Software Upgrade File via Diskettetar -xvf device eject deviceSoftware Upgrade Instructions foreextract devicemkdir /tftpboot 6.2 Performing the Software Upgrademv ﬁlename /tftpboot operation upgrade ?operation upgrade 169.144.3.54ASX-200BX4.0.01.3 operation upgrade 169.144.3.54asx-scp4.0.01.3Software Upgrade Instructions Reboot the switchy? y Software Upgrade InstructionsSoftware Upgrade Instructions 6.3 Changing between Multiple Versions of Softwarelocalhostoperation reboot Software Upgrade InstructionsAre you sure you want to reboot this switch n? y 6.4.2 Setting Up Your bootp Server 6.4 Using bootp to Download Software to the Switch6.4.1 Overview Software Upgrade Instructions6-10 6.4.3 Adding an Entry for Your Switch in the bootptab FileSoftware Upgrade Instructions Software Upgrade Instructions 6-11The variables in the previous example are deﬁned as follows 6-12 6.4.4 Setting Up a tftpboot ServerSoftware Upgrade Instructions A.1 Adapter Hardware Troubleshooting TroubleshootingAPPENDIX A Figure A.1 - Adapter Hardware Troubleshooting Flowchart TroubleshootingTroubleshooting A.1.1 Run LooptestA.1.3 Firmware Download Automatically Performed A.1.2 Check Self-Test Automatically PerformedTroubleshooting netstat A.1.4 Hardware Detected by DriverTroubleshooting atmstat fa0 A.1.5 Check FirmwareTroubleshooting Troubleshooting A.1.6 Check Physical LinkTroubleshooting A.2 Testing Network Connectivity Using PVCsFigure A A-10 ping IPaddressofremoteworkstationTroubleshooting A-11 A.2.1 Verifying the Outgoing ATM ARP EntryTroubleshooting A-12 A.2.2 atmstatTroubleshooting Troubleshooting A-13A.2.2.2 Cells and VPI/VCI Errors Received by Remote A.2.2.3 Cells and AAL* Errors Received by RemoteTroubleshooting A-14A.2.2.5 Cells and No Errors Received by Remote and Transmitting Cells A.3.1 Basic Information A.3 Collecting Additional InformationA.3.2 Adapter Information A-15ifconﬁg fa0 uname -anetstat -nr A-16adinfo fa0 netstat -inA-17 TroubleshootingA-18 A.3.3 Switch InformationTroubleshooting cport switchname asxmon switchnameA-19 Troubleshootingconﬁguration port show conﬁguration spans showA-20 Troubleshootingconﬁguration port ds3 show conﬁguration port taxi showA-21 Troubleshootingconﬁguration port sonet show conﬁguration port ds1 showconﬁguration e1 show conﬁguration port e3 showB.1 SFCS-200WG, SFCS-200BX, SFCS-1000 Diagnostics SCP DiagnosticsAPPENDIX B SCP Diagnostics B.1.1 Accessing the Monitor ModeSCP Diagnostics SCP Diagnostics B.1.2 Running the Hardware TestsB.1.2.1 Clock Test B.1.2.2 DRAM TestB.1.2.3 DRAM Chip Test SCP DiagnosticsB.1.2.4 Ethernet Test B.1.2.5 FLASH TestB.1.2.6 FLASH Chip Test SCP Diagnostics=test-fc 1 Save Chip B.1.2.9 Timer Test SCP DiagnosticsTimer OK Clock OK DRAM OK Ethernet OK Timer OK Serial OK=test-manufact Clock OK DRAM OK Ethernet OK Timer OK SCP DiagnosticsB.1.2.11 Complete Hardware Test APPENDIX C C.1 Cabletron ATM SwitchesHardware Speciﬁcations C.1.1 SFCS-200WG Hardware SpecificationsHardware Specifications C.1.2 SFCS-200BXHardware Specifications C.1.3 SFCS-1000C.2.1 100 Mbps TAXI Module C.2 ATM Network ModulesHardware Specifications Hardware Specifications C.2.2 155 Mbps OC-3c/STM-1 MM ModuleHardware Specifications C.2.3 155 Mbps STS-3c/STM-1 UTP ModuleSignal Hardware SpecificationsSignal Name C.2.3.2 Connecting Switches with 155 Mbps UTP Network ModulesHardware Specifications C.2.4 622 Mbps OC-12c/STM-4c MM ModuleC-10 C.2.5 25 Mbps TP25 ModuleHardware Specifications Hardware Specifications C-11C.2.5.1 Connecting Switches with TP25 Network Modules Hardware Specifications C-12C-13 C.2.6 34 Mbps E3 ModuleHardware Specifications C-14 C.2.7 45 Mbps DS3 ModuleHardware Specifications C-15 C.2.8 155 Mbps OC-3c/STM-1 SM ModuleHardware Specifications C-16 C.2.9 155 Mbps OC-3c/STM-1 3MM/1SM ModuleHardware Specifications Hardware Specifications C-17Description C-18 C.2.10 622 Mbps OC-12c/STM-4c SM ModuleHardware Specifications C.3.1 Adapter Cabling Speciﬁcations C.3 ATM AdaptersC-19 Hardware SpecificationsHardware Specifications C-20C.3.1.2 UTP Cable Speciﬁcations C-21 C.3.2 ESA-200PC Technical SpeciﬁcationsHardware Specifications C-22 C.3.3 PCA-200PC Technical SpeciﬁcationsHardware Specifications C-23 C.3.4 PCA-200MAC Technical SpeciﬁcationsHardware Specifications C-24 C.3.5 NBA-200 Technical SpeciﬁcationsHardware Specifications C-25 C.3.6 GIA-200 Technical SpeciﬁcationsHardware Specifications C-26 C.3.7 HPA-200 Technical SpeciﬁcationsHardware Specifications C-27 C.3.8 MCA-200 Technical SpeciﬁcationsHardware Specifications C-28 C.3.9 SBA-200 Technical SpeciﬁcationsHardware Specifications C-29 C.3.10 ESA-200 Technical SpeciﬁcationsHardware Specifications C-30 C.3.11 VMA-200 Technical SpeciﬁcationsHardware Specifications Hardware Specifications C-31 Hardware Specifications C-32 GLOSSARY ATM Link - a virtual path link VPL or a virtual channel link VCL GLOSSARYGLOSSARY atmconﬁg - a FORE program used to enable or disable SPANS signallingCell - an ATM Layer protocol data unit PDU GLOSSARYCell Header - ATM Layer protocol control information GLOSSARYDSn Digital Standard n 0, 1, 1C, 2, and 3 - a method that deﬁnes the rate and format of digital hierarchy GLOSSARYEPROM - Erasable Programmable Read Only Memory See PROM GLOSSARYHPUX - the Hewlett-Packard version of UNIX GLOSSARYnnn.nnn.nnn.nnn GLOSSARYGLOSSARY g-10GLOSSARY g-11Layer Entity - an active layer within an element GLOSSARY g-12GLOSSARY g-13OpenView - Hewlett-Packard’s network management software GLOSSARY g-14Peer Entities - entities within the same layer GLOSSARY g-15Point-to-Point Connection - a connection with only two endpoints GLOSSARY g-16PVC Permanent Virtual Circuit or Channel - a circuit or channel through an ATM network provisioned by a carrier between two endpoints used for dedicated long-term information transport between locations GLOSSARY g-17SGMP Simple Gateway Management Protocol - the predecessor to SNMP STS Synchronous Transport Signal - a SONET electrical signal rate g-18GLOSSARY Switched Connection - a connection established via signalling g-19GLOSSARY GLOSSARY g-20VCI Virtual Channel Identiﬁer - the address or label of a VC GLOSSARY g-21VPI Virtual Path Identiﬁer - the address or label of a particular VP GLOSSARY g-22