Using Alarm Conﬁguration, From the icon | Cabletron Systems EMM-E6

Alarm Conﬁguration

Using Alarm Conﬁguration

To open the Alarms window

from the icon:

1.Click on the appropriate EMM-E6 icon to display the icon menu.

2.Drag down to Alarm Conﬁguration and release.

from the Hub View:

1.In the Hub View, click on to display the Device menu.

2.Drag down to Alarm Conﬁguration and release to open the Repeater Alarms window.

from the command line (stand-alone mode):

1.From the appropriate directory type:

spmarun r4al <IP Address> <community name>

NOTES

The spmarun script invoked ﬁrst in the above command temporarily sets the environment variables SPMA needs to operate; be sure to use this command any time you launch an application from the command line. The script is automatically invoked when you launch the application from the icon menu or from within the Hub View.

If you wish to change any Alarm Conﬁgurations, be sure to use a community name with at least Read/Write access. If you only wish to view current settings, a community name with Read access will be sufﬁcient.

If there is a hostname mapped to your EMM-E6’s IP address, you can use <hostname> in place of <IP address> to launch this application. Please note, however, that the hostname is not the same as the device name which can be assigned via Local Management and/or SPMA; you cannot use the device name in place of the IP address.

Figure 3-1. Repeater Alarms Window

3-2	Using Alarm Conﬁguration

Image 52

Contents

EMM-E6 Page Virus Disclaimer Restricted Rights Notice Contents Chapter Source Addressing Chapter Security Chapter Front Panel Redundancy Appendix a EMM-E6 MIB Structure Contents Using the EMM-E6 User’s Guide Introduction Using the EMM-E6 User’s Guide What’s not in the EMM-E6 User’s Guide UPS Conventions Screen Displays Window Conventions Using the Mouse Button Getting Help EMM-E6 Firmware Year 2000 Compliance Using the EMM-E6 Hub View Using the Hub View Navigating Through the Hub View Hub View Front Panel Uptime Date and TimeDevice Name Device Location Using the EMM-E6 Hub View EMM-E6 Ports Display Using the Mouse in a Hub View Module Brim Ports Hub View Port Color Codes Port Display Form Monitoring Hub Performance Port Display Form Errors LoadTrafﬁc Collisions Frame Sizes ProtocolsPort Type Using the EMM-E6 Hub View Name and Location Checking Device Status and Updating Front Panel InfoContact Checking Network Status Chassis Type Name Active Users Checking Module Status Module Type Checking Port Status Link Status Status Media Type Viewing the IP Address Table Topology Type Launching the Global Find MAC Address Tool Checking Statistics Using the EMM-E6 Hub View Received Bytes Total PacketsAvg Packet Size Broadcast Packets Total Errors Alignment ErrorsCRC Errors OOW Collisions Runt Frames Giant Frames Viewing the Port Source Address List Protocols/Frames Statistics Using the EMM-E6 Hub View Setting the Polling Intervals Managing the Hub Contact Status Device General Status Conﬁguring FNB Connections Device ConﬁgurationPort Operational State Statistics Conﬁguring RIC MIM Connections To conﬁgure FNB connectivity for an individual port Setting a Port’s Trunk Type 15. Tpxmim Channel Selection Window To change a port’s topology status Enabling/Disabling MIM Ports Alarm Conﬁguration Using Alarm Conﬁguration From the command line stand-alone modeFrom the icon From the Hub View Conﬁguring Alarms CRC Setting Repeater Alarms Broadcast Setting and Changing Alarms Set Repeater Alarms Window Setting Module and Port Alarms Setting Module Alarms Set Module Alarms Window Set the Status to Enabled Setting Port Alarms Set Port Alarms Window Set the Status to Enabled Alarm Conﬁguration Setting Module and Port Alarms What is a Segmentation Trap? Link/Seg Traps What is a Link Trap? Enabling and Disabling Link/Seg Traps Spmarun r4hwtr IP address community name Conﬁguring Link/Seg Traps for the Repeater Viewing and Conﬁguring Link/Seg Traps for Hub Modules Module Traps Window Viewing and Conﬁguring Link/Seg Traps for Ports Port Traps Window Link/Seg Traps Link/Seg Traps Enabling and Disabling Link/Seg Traps Setting Network Circuit Redundancy Repeater Redundancy Conﬁguring a Redundant Circuit Spmarun r4red IP address community name Channel X Redundancy Window Add Circuit Address Window Repeater Redundancy Monitoring Redundancy To set the Poll Interval Source Addressing Displaying the Source Address List Displaying the Source Address List Source Addressing Setting the Hash Type Setting the Aging Time Locking Source Addresses Source Address Locking on Older Devices Conﬁguring Source Address Traps Repeater-level Traps Module- and Port-level Traps Source Addressing Finding a Source Address Port Source Address Traps Window Click on to exit the window Security What is LANVIEWSECURE? Spmarun r4sec IP address SU community name Secure address assignment New deﬁnitions for station and trunk portsTrunk port security Newest Lanviewsecure Features Continuous learning modeConﬁgurable violation response Full or partial security against eavesdropping Security on Non-LANVIEWSECUREMIMs Learned addresses resetForced non-secure status Conﬁguring Security Security To assign secure addresses to a port Addresses Window Boards with Multiple Caches Add MAC Address Window Resetting Learned Addresses Tips for Successfully Implementing Eavesdropper Protection Enabling Security and Traps Security Repeater-level Security and Traps Channel X Security Window Module-level Security and Traps Channel X Module Security Window Port-level Security and Traps Channel X Port Security Window Security Setting Front Panel Redundancy Front Panel Redundancy Setting Front Panel Redundancy Add Circuit Address Window Front Panel Redundancy Setting Front Panel Redundancy Ietf MIB Support EMM-E6 MIB Structure MIB Components Chassis MGR Host Services IP ServicesRepeater One, Repeater Two, and Repeater Three Ctron Use Only Rmon Default Distributed LAN MonitorMIB Navigator Rmon Host Brief Word About MIB Components and Community Names EMM-E6 MIB Structure Index Index-2 Index-3 Index Index-4