Mute control parameter, Mute=On, On, Off | Canon X600, SX60 specs

User Command Specifications

9. Details of command MUTE

1

Commands

MUTE

Mode

Control

Setting

Reference

Function

Mute control

Format

MUTE=<Mute control parameter: ID>

Parameter

Mute control parameter

Parameter

Meaning

ON

This turns off the audio/beep sound.

OFF

This returns the audio/beep sound to its original setting.

ID

The parameters which can be set at any given point in time can be obtained using the

RANGE command.

For details, refer to the RANGE command.

Response

"i:OK" is returned if the parameter was set properly.

For all other responses, refer to "Error List."

Description

This command is used to set the sound output muting to ON or OFF.

-1 It can be executed when the projector is in both the remote mode and power-onstatus at the

same time.

A "busy" response is given while the zoom or focus lens is being driven.

(Refer to the ZCONTDRV command and FCONTDRV command.)

-2 The mute setting is always "OFF" when the power has just been turned on.

-3 This command is identical to pressing the MUTE button on the remote control.

-4 Mute control enables simultaneous control of the audio and beep sound.

-5 The current muting status can be acquired using the applicable GET command.

For details, refer to the GET command.

Example

Setting

> MUTE=ON

This mutes the volume.

< i:OK

Reference

> GET MUTE or ?MUTE

This retrieves the volume state.

< g:MUTE=ON

Acquisition of parameters which can be set

> RANGE MUTE

< r:MUTE=I,

ON, OFF

"ON" or "OFF" can be set for muting control.

* Commands are indicated by ">", and responses are indicated by "<".

Commands

SX50

SX6

SX60

X600

supported

01.00**

01.01**

01.01**

01.01**

○

○

○

○

Supported Command States

Model

Power

Input

Mode

Remarks

OFF

ON

PM

D-RGB

A-RGB1

A-RGB2

Comp

Video

S-Video

D-Video

SCART

None

Remote

Local

SX50

×

○

×

○

○

○

○

○

○

–

–

○

○

×

SX6

×

○

×

○

○

○

○

○

○

○

○

○

○

×

SX60

X600

*If a command cannot be supported, 'INVALID_MODE' or 'NOT_POWER_SUPPLIED' is returned as an error response.

*"i:BUSY" may be returned if the power status is being switched.

PAGE 50

Image 58

Canon X600, SX60 specifications Mute control parameter, Mute=On, On, Off

Contents

Canon projector SX6/SX60/X600 User Commands User Command Specifications Version revision history II Contents GET Noshowstatus Range Range PowerGET 6AXADJ GET 6AXR～6AXY GET Lamp Range Sharp Range Rcch Range Guid Range Dpon Overview Description Communication Specifications Command sent from the PC Range Response character string Delimiter Error response character string= eError codeError messageResponse OK response character string=iOK Shield CD DCD RD RXD SD TXD ER DTR SG GND DR DSR OtherCable RS RTS CS CTS Communication Flow Lost, and the mode is reset to receive standby againCommands Delimiter is considered transmission received Command System SX6, SX60 or X600 User Command System GET Comver Error Control ModeRemote Local GET Mode Main ALM Local mode Remote mode Key/Emulation function Events for returning from standby mode ・Signal input Power Management ModeGET/RANGE Command List Parameter Details of commandFormat Description User Command Specifications SET command User Command Specifications GET command User Command Specifications Range command Remote CommandsFunction GET Mode or ?MODE GMODE=LOCAL This switches to Local modeGET Romver GET Signalstatus Main Switch to Local mode Power on PowerFormat Power Parameter ：ＩＤ Example Control Autoｓｅｔexe CommandsExample Setting Format AUTOSETEXEAuto set parameter：ＩＤ Parameter Format BLANK=BLANK parameter：ＩＤ Parameter BlankFunction Response Input Format INPUT=Input selection parameters ：ＩＤ Autopc Autopc Format DOTS=Number of dots Number Example SettingDots Range Ｄｏｔｓ Track Format TRACK=Adjustment value NumberParameter Adjustment value TRACK=25 HPOS/VPOS Range Hpos HPIX/ Vpix Range Vpix Format SEL=Input signal selection parameter ID SEL ASPECT=WIDE AspectTrue Range Aspect Image Supported Command States BRI Format BRI=Brightness setting NumberRange BRI Format CONT=Contrast setting Number Cont Sharp Format SHARP=Sharpness setting NumberSHARP=3 Gamma Format GAMMA=Gamma adjustment NumberRange Gamma DGAMMA=1 DgammaOFF Range Dgamma Prog OFF Auto Supported Command States Greenboard AdjustNormal WB=NORMAL Image adjustments Screen color correction Adjustments Adjustment value NumberAn iOK is returned after setting is successful Wbrgb SAT Range SAT SX50 Image adjustments Hue Format HUE=Hue setting value ：NumberHUE Example RgbgainRange Rgbgain Format Setting：Number ParameterRgboffset Range Rgboffset Acadjust Memcadj Example Control 6AXADJ=ON Format 6AXADJ=6-axis adjustment parameter：ＩＤ Parameter6AXADJ Range 6AXADJ 6AXR-Y Range 6AXC Lamp Format LAMP=Lamp output setting parameters ：ＩＤLAMP=NORMAL Reset Lamptime ResetFormat RESETReset parameters：ＩＤ System Format VKS=Vertical keystone distortion value Number VKS/HKSRange HKS Format AVOL=Audio volume level Number Avol Mute control parameter MuteMute control MUTE=ON Format BVOL=Beep sound setting Number Bvol Imageflip Format IMAGEFLIP=Image flip setting parameters ：ＩＤIMAGEFLIP=REAR PMM Format PMM=Power management setting parameters ：ＩＤPMM=STANDBY Pjon PJON=CANON Black screen This sets the Blue screen when no signals are inputNosig Blue screen Blue NoshowBlack Logo Logopos Lang OUT Format TERMINAL=Terminal setting parameters ：ＩＤTerminal TERMINAL=IN KEYLOCK=RC Format KEYLOCK=Key lock setting parameters ：ＩＤKeylock Range Keylock Rcch Format RCCH=Remote control setting parameters ：ＩＤRange Rcch GUIDE=ON Format GUIDE=Guide setting parameter：ＩＤ ParameterGuide Range Guide DPON=ON Format DPON=Direct power-on setting parameter：ＩＤ ParameterDpon Range Dpon LEDILLUMINATE=ON LedilluminateRange Ledilluminate ZSTEPDRV=TELE ZstepdrvWide Range Zstepdrv GET Comver ZcontdrvGET Romver ZCONTDRV=TELE FSTEPDRV=NEAR FstepdrvRange Fstepdrv Fcontdrv FCONTDRV=NEAR Menu Commands ModeRemarks Button Down RC Power iOk Parameter Main unit panel emulation button parameters ＭａｉｎFunction Front panel operation emulation Format Key assignments for the front panel buttons are shown below GET Format GET Parameter ? Parameter GET Mode GET Mode ? Mode GET Power ? Power GET PowerResponse GPOWER=Power status ID Getblank ?BLANK GET BlankResponse GBLANK=BLANK status：ＩＤ Response GINPUT=Input type ID GET InputGET Input This inquires about the current input selection GET Dots GET DotsResponse GDOTS=Total number of dots Number GET Track Response GTRACK=Tracking adjustment value NumberTracking adjustment value inquiry GET Track ? Track GET Hpos GET Vpos GVPOS=Vertical position adjustment value NumberGET HPOS/VPOS ? Vpos GET Hpix Vertical resolution inquiryGET HPIX/VPIX ? Hpix ? Vpix GET SEL ? SEL Response GSEL=Input signal IDGET SEL GET Aspect Response GASPECT=Screen setting ：ＩＤThis inquires about the current screen setting GET Aspect ? Aspect GET Image Response GIMAGE=Image mode ：ＩＤGET Image ? Image GET BRI GET BRI? BRI Response GET Contrast value setting inquiryContrast can be set by the Cont command Response GCONT=Contrast value Number This inquires about the current sharpness value setting Sharpness value setting inquiryResponse GSHARP=Sharpness setting Number GET Sharp GET Gamma Response GGAMMA=Gamma adjustment value ：NumberThis inquires about the current gamma adjustment value GET Gamma ? Gamma GET Dgamma Dynamic gamma value setting inquiryResponse GDGAMMA=Setting ID GET Dgamma ? Dgamma GET Prog GET ProgResponse GPROG=Set status value ID GET WB GET WB? WB Response GET Wbrgb ? Wbrgb Screen color correction adjustment inquiryGET Wbrgb GET Wbrgb or ? Wbrgb GET SAT ? SAT Response GSAT=Color saturation value setting NumberColor saturation value setting inquiry GET SAT GET HUE GET HUE? HUE Response GET Rgbgain Mode Control SettingFunction RGB gain adjustment value inquiry Format Getrgbgain ?RGBGAIN GET Rgboffset Function RGB offset adjustment value inquiry FormatGetrgboffset ?RGBOFFSET Response GACADJUST=Details of adjustment ：ＩＤ GET AcadjustGET Acadjust ? Acadjust GET Acadjust or ? Acadjust GACADJUST=6AX GET Memcadj Response GMEMCADJ=Details of adjustment：ＩＤGetmemcadj ?MEMCADJ GET 6AXADJ Response G6AXADJ=Setting：ＩＤGET6AXADJ ?6AXADJ GET 6AXR GET 6AXG GET 6AXB GET 6AXC GET 6AXM GET 6AXY Axis correction R to Y hue/color saturation setting inquiryGET 6AXR-6AXY ? 6AXG ? 6AXB ? 6AXC ? 6AXM GET Lamp Response GLAMP=Setting ：ＩＤGET Lamp GET VKS/HKS ? VKS ? HKS Response GVKS=Vertical keystone setting NumberVertical/horizontal keystone setting inquiry GET VKS GET HKS GET Avol Audio volume setting inquiryGET Avol GET Avol or ? Avol GAVOL=18 GET Mute Mute control setting inquiryResponse GMUTE=Setting ：ＩＤ GET Mute GET Bvol Response GBVOL=Setting ＩＤGET Bvol GET Imageflip Flip display setting inquiryResponse GIMAGEFLIP=Setting ：ＩＤ ? Imageflip GET PMM ? PMM Response GPMM=Setting ：ＩＤ（Refer to the Zcontdrv command and Fcontdrv command ） GET PMM GET Pjon GET Pjon ? Pjon GET Nosig Response GNOSIG=Setting ：ＩＤGET Nosig Black screen GET Noshow Response GNOSHOW=Setting ：ＩＤGET Noshow ? Noshow GET Logopos Response GLOGOPOS=Setting ：ＩＤUser image position can be set by the Logopos command ? Logopos GET L ＡＮＧ GET LangLanguage inquiry Response GLANG=Language ：ＩＤ GET Terminal ? Terminal GET TerminalOUT GET Keylock GET Keylock ? Keylock Setting Meaning Remote control setting inquiryResponse GRCCH=Setting ：ＩＤ GET Rcch GET Guide Response GGUIDE=Setting：ＩＤGetguide ?GUIDE GET Dpon Response GDPON=Setting：ＩＤ?DPON GET Ledilluminate Response GLEDILLUMINATE=Setting：ＩＤGetledilluminate ?LEDILLUMINATE Getnoshowstate ?NOSHOWSTATE GET NoshowstateResponse GNOSHOWSTATE=Status：ＩＤ Getfreeze GET FreezeResponse GFREEZE=Status：ＩＤ GET Signalstatus ? Signalstatus GET SignalstatusResponse GSIGNALSTATUS=Signal status ：ＩＤ GET Lampcounter ? Lampcounter GET LampcounterResponse GLAMPCOUNTER=Lamp on time Character string Error ID Meaning Error information inquiry? ERR Response GERR=Error ＩＤＩＤ GET ERR GET Prodcode ? Prodcode GET ProdcodeProduct information inquiry Response GPRODCODE=Product name Character string Function ROM version inquiry Format For all other responses, refer to Error ListGET Romver GET Romver ? Romver GET Comver Function User command version inquiry FormatUser command version = GET Comver ? Comver Range Format Range Parameter Parameter name=Type, Setting range Function Power control setting option request Format Range PowerRange Power Range Blank Rangeblank Range Autosetexe Function Auto setup setting option request FormatRangeautosetexe Range Input Input selection setting option requestRange Input RINPUT=I, D-RGB, A-RGB1, A-RGB2, COMP, VIDEO, S-VIDEO Range Dots Total dot number setting range inquiryRange Dots Range Dots Range Track Tracking adjustment range requestRange Track RTRACK=N, 0 Range Hpos Range Vpos Commands, respectivelyRange HPOS/VPOS Range Vpos Range Hpix Horizontal/vertical resolution setting range requestRange HPIX/VPIX RVPIX=N, 0 Range SEL Input signal setting option requestRange SEL RSEL=I, Auto Range Aspect Screen setting option requestRange Aspect Range Image Image mode setting option requestRange Image Range Image Range BRI Brightness setting range requestRange BRI Contrast setting range request Range Sharp Sharpness setting range requestRange Sharp Range Gamma Gamma adjustment range requestRange Gamma RGAMMA=N, -4 Range Dgamma Dynamic gamma setting option requestRange Dgamma Range Prog Progressive setting option requestRange Prog RPROG=I, 0, 1 Screen color correction option request RWB=I, NORMAL, GREENBOARD, AdjustRange WB Range WB Range Wbrgb Screen color correction adjustment range requestRange Wbrgb Set Range SAT Color saturation setting range requestRange SAT RSAT=N, -20 Range HUE Hue setting range requestRange HUE RHUE=N, -20 Range Rgbgain Function RGB gain adjustment range request FormatRangergbgain Range Rgboffset Function RGB offset adjustment range inquiry FormatRangergboffset RACADJUST=I, NOCORRECT, MEML, MEMM, MEMH, 6AX Range AcadjustRange Acadjust Advanced color adjustment option request Range Memcadj Rangememcadj Range 6AXADJ Function 6-axis adjustment option inquiry FormatRANGE6AXADJ Range 6AXR-6AXY R6AXC=N, -20, 20, -20 Range Lamp Lamp output setting option requestRange Lamp Range VKS Vertical/horizontal keystone setting range requestRange VKS/HKS RHKS=N, -30 Range Avol Audio volume setting range requestRange Avol RAVOL=N, 0 Range Mute Mute control setting option requestRange Mute RMUTE=I, ON, OFF Range Bvol Beep sound setting option requestRange Bvol Range Imageflip Flip display setting option requestFlip display can be set using the Imageflip command Range Imageflip Range PMM Power management setting option requestRange PMM Range Pjon Display screen at startup setting option requestRange Pjon To be set Be set Range NosigRNOSIG=I, BLACK, BLUE, Logo Range Noshow Display screen when nothing is shown setting option requestRNOSHOW=I, BLACK, BLUE, Logo Range Logopos User image position setting option inquiryRLOGOPOS=I, UPPERL, UPPERR, CENTER, LOWERL, Lowerr Range Lang Language setting option requestRange Lang Range Terminal Function Terminal setting option request FormatRange Terminal Range Keylock Key lock setting option requestKey lock can be set by the Keylock command RKEYLOCK=I, MAIN, RC Range Rcch Remote control setting option requestRange Rcch Range Guide Rangeguide Range Dpon Rangedpon Range Ledilluminate Rangeledilluminate Function Zoom lens step drive control option request Format Range ZstepdrvRangezstepdrv Rangecontzdrv Range ZcontdrvRange Zcontdrv Range Fstepdrv Rangefstepdrv Rangefcontdrv Range FcontdrvRange Fcontdrv Error List NOS HOW TimerOther DZ OOMP, D Zoomm Appendix 1 Reset Items Appendix 2 Table of Response Patterns by Command 1/3 Appendix 2 Table of Response Patterns by Command 2/3 Appendix 2 Table of Response Patterns by Command 3/3