Canon SX60, X600 specifications Error List

User Command Specifications10. Error List

10. Error List

		TYPE		Errors
Item	Code		Error character strings	supported by		Error	Remedy
				model
				(1) (2) (3) (4)
1	0001	e	BAD_SEQUENCE	○ ○ ○ ○ Communication sequence error			Wait until the response is received to send
							the command.
2	0002	e	INVALID_COMMAND	○ ○ ○ ○ Command is invalid (undefined).			Send the correct command.
3	0003	e	INVALID_MODE	○ ○ ○ ○ The designated command cannot be			Switch the mode using the REMOTE or
						executed in this mode.	LOCAL command.
4	0004	e	INVALID_FORMAT	○ ○ ○ ○ The command format is incorrect.			Send in the correct command format.
5	0005	e	NOT_POWER_SUPPLIED	○ ○ ○ ○ Power is not being supplied.			Use the POWER ON command to turn on
							the power.
6	–	i	BUSY	○ ○ ○ ○ Mode switching or processing inside the			Wait until the power supply state changes
						projector is underway.	to “ON”, “OFF”, or “PMM”.
7	000A	e	INVALID_PARAMETER			The parameter (type) is invalid	Use the correct parameter(s).
				○ ○ ○ ○ (undefined).This includes the case when
						the number of parameters is incorrect.
8	000B	e	JOB_TIMEOUT	○ ○ ○ ○ SX50 internal processing has timed out.			Resend the command.
9	–	w	USER_COMMAND_VERSION_IS_UPDATED ○ ○ ○ ○ The user command version is being updated.				Use GET COMVER to obtain the latest
							user command version.
10	–	i	BUSY (FOCUS)	○ ○ ○ The focus lens is now being driven.			Wait until the focus lens drive stops.
		i	BUSY (ZOOM)	○ ○ ○ The zoom lens is now being driven.			Wait until the zoom lens drive stops.
	F001	e	SYSTEM (UNKNOWN)	○ ○ ○ ○ An internal error occurred.			Resend the command.
11	F002	e	SYSTEM (FOCUS)	○ ○ ○ An error occurred in AUTOSETEXE=FOCUS.			Eliminate the cause of the error, and
	F004	e	SYSTEM (AUTO_KEYSTONE)	○ ○ ○ An error occurred in AUTOSETEXE=VKS.
							resend the command.
	F005	e	SYSTEM (SCREEN_COLOR)	○ ○ ○ An error occurred in AUTOSETEXE=SCRN.
12	E0XX	e	COMMUNICATION_ERROR	○ ○ ○	○ A communication protocol violation		Resend the command.
						occurred in the projector.
						This cannot be executed with the current
13	200X	e	INVALID_SOURCE (****)	○ ○ ○ ○ input source.			Change the input source.
						The current input source is indicated in
						parentheses.
	2010	e	NO_SIGNAL	○ ○ ○ ○ There is no signal input.			Input the signal.
14						This cannot be executed with the current
	201X	e	INVALID_SIGNAL (****)	○ ○ ○ ○ input signal.			Change the input signal.
						The current input signal is indicated in
						parentheses.
		i	BUSY (NOW_SETTING)	○ ○ ○ ○ Signal setting (detection) is in progress.
		i	BUSY	○ ○ ○ ○ Preparing to switch to power management			Wait until the processing is completed.
			(POWER_MANAGEMENT_READY)			standby.
15	–	i	BUSY (INTERNAL_PROCESS)	○ ○ ○ ○ Heavy processing is in progress.
		i	BUSY (FOCUS)	○ ○ ○ The focus lens is now being driven.			Wait until the focus lens drive stops.
		i	BUSY (ZOOM)	○ ○ ○ The zoom lens is now being driven.			Wait until the zoom lens drive stops.
	0801					Numerical parameters are invalid or	Use the RANGE command to obtain the
16	0802	e	INVALID_VALUE				parameter range, and then use a
				○ ○ ○ ○ outside the range.
							parameter within the range.
	1001	e	TERMINAL_OUT			The input cannot be selected since the	Use the TERMINAL command to set the
				○			terminal to input, and then select the input
						terminal is set to output.
							again.
	1002	e	NO_LOGO_CAPTURED	○ ○ ○ ○ Processing cannot be executed since the			Register the user image.
						user image is not registered.
	1003	e	IP_NOT_AVAILABLE	○ ○ ○ ○ IP conversion cannot be performed.			Change to the correct input signal.
17	1004	e	POWER_MANEGEMENT_OFF	○ ○ ○ DPON cannot be set to ON when PMM is			Set DPON to ON when PMM is not OFF.
						OFF.
	1005	e	DIRECT_POWER_ON	○ ○ ○ PMM cannot be set to OFF when DPON is			Set DPON to OFF.
						ON.
	1006	e	NOW_BLANK			AUTOSETEXE=FOCUS or SCRN cannot	After setting BLANK to ON, resend the
				○ ○ ○ be executed since BLANK is ON.			command.
	203X	e	INVALID_RESOLUTION (***)	○ ○ ○ ○ The input signal resolution is not correct.			Change to the correct resolution of the
							input signal.
18	–	i	INPUT_NOT_FOUND			The input was not switched since no input signal	There is no action to be taken since the
				○ ○ ○ was found with AUTOSETEXE=INPUT.			status has been notified.

※The error code is expressed as a four-digit hexadecimal character string. ‘X’ is a number from ‘0’ to ‘9’ or letter from ‘A’ to ‘F’.

※Errors with the newer item numbers have higher priority. (When there is more than one error, the highest level error is returned. However, error priority is the same within the same item number.)

※Given below is the correspondence between the numbers (1) to (4) in the "Errors supported by model" column and the models concerned.

(1)SX50

(2)SX6

(3)SX60

(4)X600

PAGE 177