User Command Specifications

9. Details of command LAMP

1

Commands

LAMP

 

 

 

Mode

Control

Setting

Reference

Function

Lamp output setting

 

 

 

 

 

 

 

Format

 

LAMP=<Lamp output setting parameters:ID>

 

 

Parameter Lamp output setting parameters

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Parameter

Meaning

 

 

 

 

 

 

 

 

NORMAL

Normal

 

 

 

 

 

 

 

 

SILENT

Silent cooling

 

 

 

 

 

ID

 

The parameters which can be set at any given point in time can be obtained using the

 

 

 

RANGE command.

 

 

For details, refer to the RANGE command.

 

 

 

Response "i:OK" is returned if the parameter was set properly.

 

 

For all other responses, refer to "Error List."

 

Description This command is used to set the light quantity of the lamp to "NORMAL" or "SILENT" (reduced light

 

quantity appropriate for silent cooling).

 

-1 It can be executed when the projector is in both the remote mode and power-onstatus at the

 

 

same time.

 

 

 

 

 

 

 

 

 

A "busy" response is given while the zoom or focus lens is being driven.

 

 

(Refer to the ZCONTDRV command and FCONTDRV command.)

 

-2 This command is the same as the menu functions in the table below.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Model

Menu

 

 

 

 

 

 

 

 

SX50

[Image adjustments] - [Lamp mode]

 

 

 

 

 

 

 

 

SX6

[Image adjustments] - [Lamp mode]

 

 

 

 

 

 

 

 

SX60

 

 

 

 

 

 

 

 

X600

 

 

 

 

 

 

 

-3 The current lamp output can be acquired using the applicable GET command. For details, refer to the GET command.

Example Setting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

> LAMP=NORMAL

 

 

 

 

The lamp output is set to “NORMAL”.

 

 

 

 

 

 

< i:OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

> GET LAMP or ?LAMP

 

 

 

This retrieves the lamp output.

 

 

 

 

 

 

 

< g:LAMP=SILENT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Acquisition of parameters which can be set

 

 

 

 

 

 

 

 

 

 

 

 

 

 

> RANGE LAMP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

< r:LAMP=I, NORMAL, SILENT

 

"NORMAL" or "SILENT" can be set for the lamp output.

 

 

 

 

* Commands are indicated by ">", and responses are indicated by "<".

 

 

 

 

 

 

Commands

 

SX50

 

SX6

 

SX60

X600

 

 

 

 

 

 

 

 

 

 

supported

01.00**

 

01.01**

 

01.01**

01.01**

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Supported Command States

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Model

Power

 

 

 

 

 

 

 

Input

 

 

 

 

 

 

 

Mode

Remarks

 

OFF

ON

PM

D-RGB

A-RGB1

A-RGB2

Comp

Video

S-Video

D-Video

SCART

None

Remote

Local

 

SX50

×

×

 

 

 

 

×

 

SX6

×

×

 

 

 

 

×

 

SX60

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

X600

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

*If a command cannot be supported, 'INVALID_MODE' or 'NOT_POWER_SUPPLIED' is returned as an error response.

*"i:BUSY" may be returned if the power status is being switched.

PAGE 46

Page 54
Image 54
Canon X600, SX60 specifications Format LAMP=Lamp output setting parameters :ID, Lamp=Normal