Enabling Lldp | Cisco Systems WSC2960X48TDL specs

Configuring LLDP, LLDP-MED, and Wired Location Service

How to Configure LLDP, LLDP-MED, and Wired Location Service

you can apply a network-policy profile on the interface. This way the interface has the voice or voice-signaling VLAN network-policy profile applied on the interface.

•You cannot configure static secure MAC addresses on an interface that has a network-policy profile.

•You cannot configure a network-policy profile on a private-VLAN port.

•For wired location to function, you must first enter the ip device tracking global configuration command.

How to Configure LLDP, LLDP-MED, and Wired Location Service

Enabling LLDP

Beginning in privileged EXEC mode, follow these steps to enable LLDP:

SUMMARY STEPS

1.configure terminal

2.lldp run

3.interface interface-id

4.lldp transmit

5.lldp receive

6.end

7.show lldp

8.copy running-config startup-config

DETAILED STEPS

	Command or Action	Purpose
Step 1	configure terminal	Enters global configuration mode.
	Example:
	Switch# configure terminal
Step 2	lldp run	Enables LLDP globally on the switch.
	Example:
	Switch (config)# lldp run
Step 3	interface interface-id	Specifies the interface on which you are enabling
		LLDP, and enter interface configuration mode.
	Example:
	Switch (config)# interface

	Catalyst 2960-X Switch Interface and Hardware Component Configuration Guide, Cisco IOS Release 15.0(2)EX
56	OL-29034-01

Image 68

Cisco Systems WSC2960X48TDL manual Enabling Lldp, Configure terminal Lldp run, Lldp run Enables Lldp globally on the switch

Contents

Americas Headquarters First Published July 10Page N T E N T S Contents Configuring Auto-MDIX41 Configuring System MTU Configuring EEE Viii Bold font Document ConventionsConvention Description Reader Alert Conventions Vertical barsElement Obtaining Documentation and Submitting a Service Request Related Documentation Xii This chapter contains the following topics Information About Using the Command-Line InterfaceCommand Modes Mode Access Method Prompt Exit Method About This Mode ConfigureQuit Ctrl-Z Using the Help System Command or Action Purpose StepMode Help CLI Error Messages Understanding Abbreviated CommandsNo and default Forms of Commands How to Use the CLI to Configure Features Configuration LoggingConfiguring the Command History Error Message Meaning Command or Action Changing the Command History Buffer SizeRecalling Commands Enabling and Disabling Editing Features Disabling the Command History FeaturePrivileged Exec mode Terminal no history Editing Commands through Keystrokes Editing Command Lines That Wrap Searching and Filtering Output of show and more Commands Access-listShow more command begin include exclude regular-expression Show more command begin include exclude Command or Action Example OL-29034-01 Finding Feature Information Information About Configuring Interface CharacteristicsInterface Types This module contains the following topics Switch Ports Port-Based VLANs Switch Virtual Interfaces Trunk Ports Power over Ethernet Ports EtherChannel Port Groups Using the Switch USB Ports USB Mini-Type B Console Port Interface Connections USB Type a Ports Interface Configuration Mode Connecting VLANs with the Switch Default Ethernet Interface Configuration FeatureDefault Setting Layer 2 or switching mode switchport command VLANs 1 Interface Speed and Duplex Mode Speed and Duplex Configuration Guidelines Ieee 802.3x Flow Control How to Configure Interface Characteristics Configuring Interfaces ProcedureGigabit Ethernet port 1 on switch 1 is selected Either gigabitethernet 1/0/1 Configure terminal Adding a Description for an InterfaceDescription string Show interfaces interface-id description Interface range port-rangemacro Configuring a Range of InterfacesConfigure terminal Enters global configuration mode Define interface-range macroname Configuring and Using Interface Range MacrosVerifies the configuration of the interfaces in the range Interface range macro macroname Configuring Ethernet InterfacesSetting the Interface Speed and Duplex Parameters Speed 10 100 1000 auto 10 Nonegotiate Configuring Ieee 802.3x Flow Control Command or Action Purpose Enter interface configuration mode Configuring SVI Autostate ExcludeEnd Returns to privileged Exec mode Switchport autostate exclude Shutting Down and Restarting the InterfaceAn SVI line state up or down Interface vlan vlan-id gigabitethernet interface-id Configuring the Console Media Type This configuration applies to all switches in a stackConfigure terminal Line console Media-type rj45 End Shutdown Shuts down an interface Configuring the USB Inactivity Timeout Configure terminal Enters the global configuration mode Monitoring Interface Characteristics Command PurposeShow interfaces interface-id status err-disabled Show interfaces interface-id switchport Clearing and Resetting Interfaces and Counters Configuration Examples for Interface Characteristics Identifying Interfaces on a Stack-Capable Switch ExamplesConfiguring a Range of Interfaces Examples Adding a Description to an Interface Example Configuring the Console Media Type Example Configuring and Using Interface Range Macros ExamplesSetting Interface Speed and Duplex Mode Example Configuring the USB Inactivity Timeout Example To disable the configuration, use these commandsStandards and RFCs Standard/RFC None Release Modification Cisco IOS Release 15.02EX This feature was introducedTechnical Assistance Description Link OL-29034-01 This module contains the following sections Prerequisites for Auto-MDIXRestrictions for Auto-MDIX Information about Configuring Auto-MDIX How to Configure Auto-MDIXConfiguring Auto-MDIX on an Interface Auto-MDIX on an Interface Monitoring Auto-MDIX Example for Configuring Auto-MDIX This example shows how to enable auto-MDIX on a port Prerequisites for Ethernet Management Ports Information about the Ethernet Management Port Ethernet Management Port Direct Connection to a Switch Supported Features on the Ethernet Management Port How to Configure the Ethernet Management Port Disabling and Enabling the Ethernet Management Port Additional References What to Do Next Bootloader commands Related TopicMIBs Document Title OL-29034-01 Configuring LLDP, LLDP-MED, and Wired Location Service Lldp and Cisco Medianet Lldp and Cisco Switch StacksLldp Supported TLVs LLDP-MED Supported TLVs Wired Location Service Default Lldp Configuration Configuration Guidelines Configure terminal Lldp run Lldp run Enables Lldp globally on the switchLLDP, and enter interface configuration mode Enabling Lldp Configuring Lldp Characteristics Lldp transmit Enables the interface to send Lldp packetsLldp receive Enables the interface to receive Lldp packets Show lldp Verifies the configuration Switchconfig# lldp holdtime Configuring LLDP-MED TLVs Command or Action Purpose Step Lldp med-tlv-select End Copy running-config startup-config Lldp med-tlv-select Specifies the TLV to enable Configuring Network-Policy TLV Configuration mode. The range is 1 to Voice voice-signalingvlan vlan-idcos Dscp dvalue none untagged Configuring Location TLV and Wired Location Service Show network-policy profile Verifies the configuration Use one of the following Way Exit Returns to global configuration mode Information, and enter interface configuration modeUse one of the following Verifies the configuration Enters location information for an interface Enabling Wired Location Service on the Switch Command or Action Purpose Example Nmsp notification interval attachment location Configuring Network-Policy TLV ExamplesNmsp enable Enables the Nmsp features on the switch Command Description Civic location OL-29034-01 Information about the MTU System MTU Guidelines How to Configure MTU Sizes Configuring the System MTU Reload Reloads the operating system Configuration Examples for System MTUShow system mtu Verifies your settings Additional References for System MTU Configuring PoE Restrictions for PoE Supported Protocols and Standards Power over Ethernet PortsInformation about PoE Powered-Device Detection and Initial Power Allocation Class Power Management Modes Power Monitoring and Power Policing Maximum Power Allocation Cutoff Power on a PoE Port How to Configure PoE Configuring a Power Management Mode on a PoE Port Never static max max-wattage Budgeting Power for Devices Connected to a PoE PortShow power inline Budgeting Power to All PoE ports No cdp run Optional Disables CDP Budgeting Power to a Specific PoE Port Configure terminal No cdp run Power inline consumption wattage Configuring Power PolicingSpecifies the physical port to be configured, and enter Power inline police actionlog errdisable Exit Show power inline police Show errdisable recoveryConfiguration mode Power inline police actionlog errdisable Down the port and puts the port in the error-disabled state Power inline police action log-Generates a syslog messageWhile still providing power to the port Budgeting Power Example Monitoring Power StatusConfiguration Examples for Configuring PoE Information About EEE EEE Overview How to Configure EEE Default EEE ConfigurationEEE is disabled by default Restrictions for EEE Specifies the interface to be configured, and enter Power efficient-ethernet autoCommand Monitoring EEE This example shows how to disable EEE for an interface Configuration Examples for Configuring EEEThis example shows how to enable EEE for an interface Feature History and Information for Configuring EEE OL-29034-01 D E PoE