Routine Maintenance, Maintenance Of Rectifier | Emerson 48330

72	Chapter 6 Routine Maintenance

Chapter 6 Routine Maintenance

6.1Maintenance Of Rectifier

The fan of rectifier shall be maintained periodically.

The fan shall be replaced if it does not work due to faults.

Follow the procedures below to replace the fan:

1.Loosen the 3 screws on the baffle and remove the baffle.

2.Unplug the power cable of the fan and remove the fan.

3.Replace the fan.

4.Plug the fan power cable back into the corresponding socket.

5.Push back the fan (the side with the tag facing inward).

6.Mount the front baffle and fix it with screws.

6.2Maintenance Of SCU

If any SCU fault affects the normal operation of DC power system, just turn off the SCU.

6.3Maintenance Of MFU

1. Short-circuit of load

If some of the loads have short circuit fault, just turn off the circuit breakers in the MFU to disconnect the power to the loads.

2. MFU short-circuit

When MFU short-circuit occurs, disconnect the AC power supply, isolate the batteries from the system, and then use battery or rectifier to directly supply power to load.

ACTURA Flex 48330 Power System User Manual

Image 82

Emerson 48330 user manual Routine Maintenance, Maintenance Of Rectifier, Maintenance Of SCU, Maintenance Of MFU

Contents

Version V1.0 Revision date May 20 31011084 Safety Precautions Electrical Safety Battery Special Safe Requirements of This Equipment Others Contents System Settings Alarm Settings TestingTemperature Compensation Coefficient Parameters Routine Maintenance Daily Inspection Replacement Appendix 15 Value description of AC settings Changing audible/visual alarm and alarm call back planFunctions of SCU keys Figure List Page Abbreviation FeaturesSystem Description Introduction System Configuration Outline of the DC Power System is illustrated in Figure Configuration Cabinet dimension % 0.6 % 0.6 m % 0.6 % 0.4 m Configurations of Actura Flex 48330 Power SystemSCU BCU Rectifier Shelf ComponentsOutline Connector board Dimension of Rectifier Shelf are given in TableDimensions of rectifier shelf Manufacture type Wmm ×Dmm ×Hmm Dimensions Rectifier Multi-Communication mode Function of indicatorsDimension H % W % D132mm % 85mm % 287mm Weight 0.76kg 3 SCU Alarm category settings for dry contact output Functions fulfilled by SCU and MC Level Authority Default password Password protection for important operationsAuthority and default password Multi-Function Unit MFU Alarm output Battery Connection Unit BCUConfiguration of MFU Component Description 0m % 0.6m % 0.6m cabinet BCU configurationSystem Cabinet 0m % 0.6m % 0.4m cabinet Power Supply InstallationInstallation Preparation Environmental conditions in power room Site Survey Tools & Material Unpacking Installation on the floor Installation ProceduresCabinet Installation Drill reserve holes Installing expansive pipe Connection requirements External Electrical Connection InterfaceConnection Of Input Cables AC input modes Connection of input terminals Different cable connection modes Connection of single-phase AC power input Connection Of Load Cables Configuration number of load MCBs and battery MCBsBusbar type Max. load number 12 Connector board in rectifier shelf Connection Of Communication Cables Layout Of Connector Board S6415X2 13 Layout of connector board S6415X2 Interface definition of connector board S6415X2 Interface Definition Of Connector Board S6415X2Connector Pin Signal name Mark number Logic relation Pgng POWER+ Power Connection Of Temperature Sensor CablesConnector Pin Signal name Connection With Modem Connecting method Battery Installation And CablingBattery Installation Connection With Dry Contacts Battery Cable Connection Standard configuration 16 Connection of battery cables Non-standard configuration 18 Negative battery cables connection in BCU Parallel Connection Of Cabinets DC/Parallel connections Startup Check the DC Power System according to -1 before startupSystem checklist before startup Checking Before Startup Parameters Configuration Startup Process Testing Rectifier TestingTesting MFU Testing SCU BCU Test Battery Breaker TestLoad Breaker Test Operation Panel Functions of LED indicatorsOperating SCU Functions of SCU keys Operation Procedures First system information page appears Querying System Status First Page Of System Information Battery information Other System Information Screen BC prompt and temperature information AC information Querying Rectifier Status Querying Alarms And Setting Alarm Plans Querying Active Alarm Query Alarm History Alarm History Alarm Type Table Alarm type table Llvd Blvd Chapter Operating SCU Serial Alarm Description Default Setting Alarm Type For Dry Contacts Changing Audible/Visual Alarm And Alarm Call Back PlanChanging Alarm Types Of Dry Contacts Changing audible/visual alarm and alarm call back plan Optional alarm types Alarm type Remark Set the Alarm Names Through PLC Function PLC SN and Alarm Logic matrix used for configuring 8 dry contactsExample of PLC setting Alarm Remark Description Alarm Remark Description PLC Maintenance Llvd Blvd Operating SCU Parameter Setting Method Setting System ParametersPress ESC to return to the menu of higher level Password levels and authorities Level Authority Batt. Selection First page of the Batt. Selection is shown below LVD Parameter Description Charging Management Parameters There are 6 related pages, as shown below Operating SCU BC/FC switchover diagram is shown below Parameter Range Default Value description12 Charging management parameter value description Battery Test Parameters There are 7 related pages, as shown below Schematic diagram of the test function is shown below 13 Value description of the battery test parametersValue description of the parameters is listed below Temperature Compensation Coefficient Parameters First page of the setting interface is shown below AC Settings Configuration interface is shown below DC Setting There are three related pages, as shown below Rect Settings 17 Value description of rectifier settings System Settings There will be a prompt when resetting the system 18 Value description of system settings EEM-M Model description is shown below 48V/50A/SET/NONE 48V/30A/SET/NONE First page of the setting interface is show below Alarm SettingsPower system model System type 19 Relationship between system model and system type 20 Value description of alarm settings Maintenance Of SCU Routine MaintenanceMaintenance Of Rectifier Maintenance Of MFU Cover Plates Battery MaintenanceStore the battery in a cool dry place Storage And Supplementary Replacement Troubleshooting TroubleshootingTroubleshooting Rectifier Symptom Cause Suggestion Mains Failure Disastrous Accidents Parameter Category Appendix System Technical ParametersEMC Mtbf Appendix 2 Engineering Design Diagram Appendix 2 Engineering Design Diagram Connector Connector specs MCB Appendix 3 System Circuit Diagram Appendix 3.1 System Electric Schematic Diagram Appendix 3.2 System Wiring Diagram Appendix 3.3 MFU Electric Wiring Diagram Appendix 3.4 BCU Electric Wiring Diagram Hvsd Appendix GlossaryAbbreviation Full word LVD