Emerson 48330 Appendix 1 System Technical Parameters

Appendix 1 System Technical Parameters 77

ACTURA Flex 48330 Power System User Manu al

Appendix 1 System Technical Parameters

Parameter category Note

AC input over-voltage

alarm point Default: 280 ! 5Vac, cofigurable through monitoring module

AC input over-voltage

recovery point

Default: 270 ! 5Vac, 10Vac lower than the AC input

over-voltage alarm point

AC input under-voltage

alarm point Default: 180 ! 5Vac, configurable through monitoring module

AC input alarm and

protection

AC input under-voltage

recovery point

Default: 190 ! 5Vac, 10Vac higher than the AC input

under-voltage alarm point

DC output over-voltage

protection point Default: 59.0 ! 0.2Vdc

DC output over-voltage

alarm point

Default: 58.5 ! 0.2Vdc, configurable through monitoring

module

DC output over-voltage

recovery point

Default: 58 ! 0.2Vdc, 0.5Vdc lower than the over-voltage

alarm point

DC output under-voltage

alarm point

Default: 45.0 ! 0.2Vdc, configurable through monitoring

module

DC output under-voltage

recovery point

Default: 45.5 ! 0.2Vdc, 0.5Vdc higher than the under-voltage

alarm point

LLVD Default: 44 ! 0.2Vdc, configurable through monitoring module

BLVD Default: 43.2 ! 0.2Vdc, configurable through monitoring

module

Output delay Output voltage can rise slowly upon rectifier start up. The rise

time is configurable

DC output alarm and

protection

Fan speed adjustable Rectifier fan speed can be set to half or full speed.

CS

RS EN300386 2001, Class A

Immunity to EFT EN61000-4-4, Level 3

Immunity to ESD Air discharge: 8kV. Contact discharge: 4kV. EN61000-4-2

EMC

Immunity to Surges EN61000-4-5, Level 4

Lightning protection

features At AC side

The AC input side can withstand 10/700μs simulated

lightning voltage 5kV for !5 times, or 8/20μs simulated

lightning surge current 20kA for !5 times, or 8/20μs

simulated lightning surge current 40kA once. The test interval

is not smaller than 1 minute.

Acoustic noise  55dB (A)

Others

Insulation resistance

At temperature of 15°C ~ 35°C and relative humidity not

higher than 90%RH, apply a test voltage of 500Vdc. The

insulation resistances between AC circuit and earth, between

DC circuit and earth, or between AC and DC circuits are no

less than 10MΩ

Contents

Main ACTURA Flex 48330 Power System User Manual Page Page Page Contents Page Page Table List Figure List Page Chapter 1 System Description 1.1 Abbreviation 1.2 Introduction 1.3 Features 1.4 System Configuration 1.5 Components 1.5.1 Rectifier Shelf Page 1.5.2 Rectifier 1.5.3 SCU Page 1.5.4 Multi-Function Unit (MFU) 1.5.5 Battery Connection Unit (BCU) 1.5.6 System Cabinet Chapter 2 Installation 2.1 Installation Preparation 2.1.1 Environmental Conditions 2.1.2 Power Supply 2.1.3 Site Survey 2.1.4 Tools & Material 2.1.5 Unpacking 2.2 Installation Procedures 2.2.1 Cabinet Installation Page 2.3 External Electrical Connection Interface 2.3.1 Connection Of Input Cables Page Page 2.3.2 Connection Of Load Cables Note 2.3.3 Connection Of Communication Cables Page 2.3.5 Interface Definition Of Connector Board S6415X2 2.3.6 Connection Of Temperature Sensor Cables 2.3.7 Connection With MODEM Note 2.3.8 Connection With Dry Contacts 2.4 Battery Installation And Cabling 2.4.1 Battery Installation Note 2.4.2 Battery Cable Connection Page Page 2.5 Parallel Connection Of Cabinets Chapter 3 Startup 3.1 Checking Before Startup 3.2 Startup Process Item Action Result Comments (Fill in OK or not) 3.3 Parameters Configuration Chapter 4 Testing 4.1 Testing MFU 4.2 Testing Rectifier 4.3 Testing SCU 4.4 Battery Breaker Test 4.5 BCU Test 4.6 Load Breaker Test Chapter 5 Operating SCU 5.1 Operation Panel 5.2 Operation Procedures 5.3 Querying System Status 5.3.1 First Page Of System Information Note 5.3.2 Other System Information Screen Note Page 5.4 Querying Rectifier Status 5.5 Querying Alarms And Setting Alarm Plans 5.5.1 Querying Active Alarm 5.5.2 Query Alarm History Page 5.5.3 Alarm Type Table Table 5-3 Alarm type table Page Page Note 5.5.4 Changing Audible/Visual Alarm And Alarm Call Back Plan 5.5.5 Changing Alarm Types Of Dry Contacts 5.5.6 Setting Alarm Type For Dry Contacts Page 5.5.7 Set the Alarm Names Through PLC Function Page PLC SN Alarm description Remark 5.6 Maintenance Page 5.7 Setting System Parameters Page 5.7.2 Batt. Selection 5.7.3 LVD Parameter Description Note 5.7.4 Charging Management Parameters Page 3. The BC/FC switchover diagram is shown below: Figure 5-2 BC/FC switchover diagram 5.7.5 Battery Test Parameters 3. The schematic diagram of the test function is shown below: Battery Auto-management Manually start battery test Rectifier output voltage lower than battery voltage Battery discharges Rectifier hot standby "Test End Voltage" is reached "Test End Cap" is reached "Test End Time" is reached 5.7.6 Temperature Compensation Coefficient Parameters Parameter Range Default Value description 5.7.7 AC Settings 1. The configuration interface is shown below: 5.7.8 DC Setting 1. There are three related pages, as shown below: 5.7.9 Rect Settings 5.7.10 System Settings Page Table 5-18 Value description of system settings Parameter Range Default Value description Parameter Range Default Value description 5. The model description is shown below: Figure 5-4 System model description 48V / 30A / 300 / NO NE Note 5.7.11 Alarm Settings Chapter 6 Routine Maintenance 6.1 Maintenance Of Rectifier 6.2 Maintenance Of SCU 6.3 Maintenance Of MFU 6.4 Cover Plates 6.5 Battery Maintenance 6.5.1 Storage And Supplementary 6.5.2 Daily Inspection 6.5.3 Replacement Chapter 7 Troubleshooting 7.1 Troubleshooting Rectifier 7.2 Mains Failure 7.3 Disastrous Accidents Appendix 1 System Technical Parameters Parameter category Note Page Page Appendix 2.3 Engineering Design Diagram For 700mm%600mm%400mm Cabinet Appendix 2.4 System Input And Output Connector Specs Page Page Page Page Appendix 4 Glossary Abbreviation Full word