Manuals / Brands / Computer Equipment / Power Supply / Emerson / Computer Equipment / Power Supply

Emerson 48330 Appendix 2.3 Engineering Design Diagram For 700mm%600mm%400mm Cabinet , Appendix 2.4 System Input And Output Connector Specs

1 96

Download 96 pages, 1.9 Mb

Appendix 2 Engineering Design Diagram 81

ACTURA Flex 48330 Power System User Manu al

Appendix 2.3 Engineering Design Diagram For 700mm%600mm%400mm Cabinet

Appendix 2.4 System Input And Output Connector Specs

Connector Connector specs

AC input terminal H cable terminals, 2-4 pcs (cable section 35 mm2)

1 M8 bolt

AC Power

distribution Grounding busbar 1 big wire connectors, (cable section 25mm2)

Positive bus bar 4 M8blots, 6 big wire connectors, (cable section 25mm2)

23 small wire connectors, (cable section 16mm2)

DC Power

distribution Output route MCB H cable terminals (cable section 25mm2)

Contents

Main ACTURA Flex 48330 Power System User Manual Page Page Page Contents Page Page Table List Figure List Page Chapter 1 System Description 1.1 Abbreviation 1.2 Introduction 1.3 Features 1.4 System Configuration 1.5 Components 1.5.1 Rectifier Shelf Page 1.5.2 Rectifier 1.5.3 SCU Page 1.5.4 Multi-Function Unit (MFU) 1.5.5 Battery Connection Unit (BCU) 1.5.6 System Cabinet Chapter 2 Installation 2.1 Installation Preparation 2.1.1 Environmental Conditions 2.1.2 Power Supply 2.1.3 Site Survey 2.1.4 Tools & Material 2.1.5 Unpacking 2.2 Installation Procedures 2.2.1 Cabinet Installation Page 2.3 External Electrical Connection Interface 2.3.1 Connection Of Input Cables Page Page 2.3.2 Connection Of Load Cables Note 2.3.3 Connection Of Communication Cables Page 2.3.5 Interface Definition Of Connector Board S6415X2 2.3.6 Connection Of Temperature Sensor Cables 2.3.7 Connection With MODEM Note 2.3.8 Connection With Dry Contacts 2.4 Battery Installation And Cabling 2.4.1 Battery Installation Note 2.4.2 Battery Cable Connection Page Page 2.5 Parallel Connection Of Cabinets Chapter 3 Startup 3.1 Checking Before Startup 3.2 Startup Process Item Action Result Comments (Fill in OK or not) 3.3 Parameters Configuration Chapter 4 Testing 4.1 Testing MFU 4.2 Testing Rectifier 4.3 Testing SCU 4.4 Battery Breaker Test 4.5 BCU Test 4.6 Load Breaker Test Chapter 5 Operating SCU 5.1 Operation Panel 5.2 Operation Procedures 5.3 Querying System Status 5.3.1 First Page Of System Information Note 5.3.2 Other System Information Screen Note Page 5.4 Querying Rectifier Status 5.5 Querying Alarms And Setting Alarm Plans 5.5.1 Querying Active Alarm 5.5.2 Query Alarm History Page 5.5.3 Alarm Type Table Table 5-3 Alarm type table Page Page Note 5.5.4 Changing Audible/Visual Alarm And Alarm Call Back Plan 5.5.5 Changing Alarm Types Of Dry Contacts 5.5.6 Setting Alarm Type For Dry Contacts Page 5.5.7 Set the Alarm Names Through PLC Function Page PLC SN Alarm description Remark 5.6 Maintenance Page 5.7 Setting System Parameters Page 5.7.2 Batt. Selection 5.7.3 LVD Parameter Description Note 5.7.4 Charging Management Parameters Page 3. The BC/FC switchover diagram is shown below: Figure 5-2 BC/FC switchover diagram 5.7.5 Battery Test Parameters 3. The schematic diagram of the test function is shown below: Battery Auto-management Manually start battery test Rectifier output voltage lower than battery voltage Battery discharges Rectifier hot standby "Test End Voltage" is reached "Test End Cap" is reached "Test End Time" is reached 5.7.6 Temperature Compensation Coefficient Parameters Parameter Range Default Value description 5.7.7 AC Settings 1. The configuration interface is shown below: 5.7.8 DC Setting 1. There are three related pages, as shown below: 5.7.9 Rect Settings 5.7.10 System Settings Page Table 5-18 Value description of system settings Parameter Range Default Value description Parameter Range Default Value description 5. The model description is shown below: Figure 5-4 System model description 48V / 30A / 300 / NO NE Note 5.7.11 Alarm Settings Chapter 6 Routine Maintenance 6.1 Maintenance Of Rectifier 6.2 Maintenance Of SCU 6.3 Maintenance Of MFU 6.4 Cover Plates 6.5 Battery Maintenance 6.5.1 Storage And Supplementary 6.5.2 Daily Inspection 6.5.3 Replacement Chapter 7 Troubleshooting 7.1 Troubleshooting Rectifier 7.2 Mains Failure 7.3 Disastrous Accidents Appendix 1 System Technical Parameters Parameter category Note Page Page Appendix 2.3 Engineering Design Diagram For 700mm%600mm%400mm Cabinet Appendix 2.4 System Input And Output Connector Specs Page Page Page Page Appendix 4 Glossary Abbreviation Full word