Manuals / Emerson / Computer Equipment / Power Supply

Emerson U/300/S/12P, 400KVA UPS Battery Connections, 2 Power cable connections for 160/200kVA UPS

Models: U /400/S/12P U/300/S/6P 160 200 U/300/S/12P 400KVA U /400/S/6P

1 79

Download 79 pages 37.39 Kb

Page 28

UPS Battery Connections

18	Chapter 3 Electrical Installation

6.Connect the system output cables between the output busbars (N3-U3-V3-W3 terminals) and the critical load and tighten the connections to 13 Nm (M8 bolt), to 26 Nm (M10 bolt), and to 50 Nm (M12 bolt). ENSURE CORRECT PHASE ROTATION.

Warning

If the load equipment will not be ready to accept power on the arrival of the commissioning engineer then ensure that the system output cables are safely isolated at their ends.

UPS Battery Connections

7.Connect the battery cables between the UPS terminals (+/-) and its associated BCB. Connect screened auxiliary cables from each BCB control board to the auxiliary terminal block (X3). OBSERVE THE BATTERY CABLE POLARITY.

Warning

Do not close the BCB before the equipment has been commissioned.

8. Refit the lower protective cover.

Note: For split bypass operation, ensure that the busbars ( ＊) between the bypass input and rectifier input are removed.

Auxiliary

terminal block

X3

Q1

Q2

Q5

*

Q3

*

*

U1

V1

W1

N1

U2

V2

W2

N2

N3

U3

V3

W3

Battery

Rectifier

Bypass

Earth

Output

connections

connections

connections

connections

Figure 3-2 Power cable connections for 160/200kVA UPS

HIPULSE U UPS Single Module And “1+N” (Expandable) 160/200/300/400kVA User Manual

Image 28

Emerson U/300/S/12P, U /400/S/12P, U/300/S/6P, 400KVA UPS Battery Connections, 2 Power cable connections for 160/200kVA UPS

Contents

HIPULSE U UPS Single Module And “1+N” Expandable 160/200/300/400kVA User ManualPage Page The Manual Describes The Following Equipment Safety Precautions The warning triangle indicates all the personal safety instructions Contents 3.3.2 Battery Control Connecting Main Cabinet And Side Cabinet3.4.1 Connecting Power Cables 3.4.2 Connecting Signal Cables6.5.1 Temperature Considerations 6.5.2 Battery PopulationBattery Protection Battery Connection9.2.2 Power Semiconductor Devices 9.2.5 Lives And Recommended Replacement Time Of Key ComponentsAppendix 1 Transportation Restraints Removing Procedures 160kVA&200kVA UPS Transportation Restraints Removing Procedures1.1 Features Chapter 1 General Description1.2 Design Concept 1.2.1 HIPULSE U Module Design1.2.2 Bypass Supplies 1.2.3 System Control PhilosophyNormal operation Mains failure1.2.4 ECO Mode For Single UPS Only Return of power mainsOff-battery UPS module fault1.3 Operation Mode 1.2.5 UPS Power Switch Configuration1.2.6 Battery Circuit Breaker 1.2.7 Battery Temperature CompensationAuto-restart mode Bypass modeMaintenance mode Source Share modeChapter 2 Mechanical Installation 2.1 Notes2.2 Environmental Considerations 2.2.1 UPS Location2.2.2 Battery Location 2.3 Mechanical Considerations2.3.1 System Composition 2.3.2 Moving The Cabinets2.5 Installation Drawings 2.4 Preliminary Checks1905 Front viewGrille for air entry from the bottom Surface loading of UPS4× 104cm2 , 2.7Kg\cm2Chapter 2 Mechanical Installation 14 holes for securing unit to 可拆卸栅板 Figure 2-6 Base view of 300kVA UPS 6-pulse rectifier unit in mm1910 可拆卸栅板 1591*1 1件卸下栅板可用于叉车搬运，安装后可用于防护通风 1685Ventilation the bottomChapter 3 Electrical Installation 3.1 Power Cabling3.1.1 System Configuration 3.1.2 Cable Rating3.1.5 Safety Earth 3.1.3 General Notes3.1.4 Cable Connections 3.1.6 Protective Devices3.1.7 Cabling Procedure Common Input ConnectionsSplit Bypass Connections Output System ConnectionsUPS Battery Connections Figure 3-2 Power cable connections for 160/200kVA UPSFigure 3-3 Power cable connections for 300/400kVA UPS 3.2 Distance From Floor To Connection PointTable 3-2 Distance from floor to connection point 3.3 Control Cabling 3.3.1 Monitoring Board PortsDry contact output port Table 3-4 Description of maintenance bypass cabinet portFigure 3-6 Dry contact output port Auxiliary DC power output port EPO input portCommunication ports Table 3-5 Description of dry contact output portTable 3-7 Communication port resource deployment table 3.3.2 Battery ControlFigure 3-8 Auxiliary terminal block 3.4.1 Connecting Power Cables 3.4 Connecting Main Cabinet And Side CabinetChapter 3 Electrical Installation 3.4.2 Connecting Signal Cables J10 J1 J2 J3 J4 ULW36CSA8J7 J11 J12 Chapter 4 Operator Control And Display Panel 4.1.1 LED Indicators4.1 Introduction 4.1.3 Control Buttons 4.1.2 Buzzer4.1.4 LCD And Menu Keys 4.1.5 Detailed Description Of Menu Items Adjusts time in 24-hr format and Date format in user defined format SettingsChapter Operator Control And Display PanelChapter 4 Operator Control And Display Panel 4.1.6 EPO Button 4.2 LCD Screen Types4.2.1 Start Screen 4.2.2 Primary Screen 4.2.3 Default Screen4.2.4 Help Screen 4.3 Prompt Window Help screen4.4 UPS Alarm Message List Prompt to press the Enter key F4 to acknowledge that the all paralleled UPS will be disconnected Chapter 4 Operator Control And Display Panel Chapter 4 Operator Control And Display Panel 5.1.2 Power Switches Chapter 5 Operating Instructions5.1 Introduction 5.1.1 NotesFigure 5-1 Power switch location of 160/200kVA UPS Service socket Designed for use in UPSservice, cannot be used for other purposes Figure 5-2 Power switch location of 300/400kVA UPS5.3 Start-Up Procedure Into ECO Mode 5.2 Start-Up Procedure Into Normal ModeThe UPS is now operating in Normal mode 5.4 Battery Test Mode Procedures 5.5 System Test ProcedureThe UPS is now operating in ECO mode Battery test type and preconditions5.6 Maintenance Bypass Procedure And UPS Shut Down 5.7 Shutdown Procedure Complete UPS And Load Shutdown5.8 EPO Procedure 5.9 UPS Reset Procedure5.11 Language Selection 5.10 Auto Restart5.12 Changing The Current Date And Time Chapter 6 Battery 6.2 Safety6.1 Introduction 6.3 UPS Batteries6.4 Installation Design Considerations 6.5 Battery Installation And Maintenance6.5.1 Temperature Considerations 6.5.2 Battery Population6.6 Battery Protection 6.7 Battery Connection6.8 Battery Installation 6.7.2 Connecting The Battery6.9 BCB Box Optional 6.10 Battery Temperature Sensor Optional Figure 6-5 BCB box connection7.2 “1+N” System Installation Procedures Chapter 7 “1+N” System7.1 General 7.2.1 Preliminary Checks7.2.2 Cabinet Installation 7.2.4 Power Cables7.2.3 Protective Devices Figure 7-1 “1+N” system block diagramRefer to 3.3.2 Battery Control 7.3 “1+N” System Operating Instructions7.2.5 Control Cables Refer to the EPO input port X2 part in 3.3.1 Monitoring Board Ports7.3.1 Start-Up Procedure Into Normal Mode 7.3.2 Maintenance Bypass Procedure And UPS Shut Down7.3.4 Insertion Procedure Of One Module In A Parallel System Refer to 5.2 Start-Up Procedure Into Normal Mode7.4 Dual Bus System Installation Procedures 7.3.5 Shutdown Procedure Complete UPS And Load Shutdown7.4.1 Cabinet Installation Refer to 5.7 Shutdown Procedure Complete UPS And Load Shutdown7.4.3 Power Cables 7.4.4 Control Cables并机电缆 Parallel cable 并机电缆 Parallel cableChapter 8 Specifications 8.3 Mechanical Characteristics8.4 Electrical Characteristics Input Rectifier 8.1 Conformity And Standard8.5 Electrical Characteristics DC Intermediate Circuit Table 8-5 Electrical characteristics DC intermediate circuit8.6 Electrical Characteristics Inverter Output 8.7 Electrical Characteristics Bypass Input MainsTable 8-6 Electrical characteristics inverter output Table 8-7 Electrical characteristics bypass input mains8.8 Electrical Characteristics System Performance 8.9 Electrical Characteristics ECO ModeTable 8-8 Electrical characteristics system performance Table 8-9 Electrical characteristics ECO modeChapter 9 Service & Maintenance 9.1 Safety9.2.2 Power Semiconductor Devices 9.2 UPS Key Components And Their Lives9.2.6 Replacing Fuses 9.2.5 Lives And Recommended Replacement Time Of Key ComponentsTable 9-1 Lifves and recommended replacement time of key components Appendix 1 Transportation Restraints Removing Procedures 1. 160kVA&200kVA UPS Transportation Restraints Removing Procedures2. 300kVA UPS Transportation Restraints Removing Procedures A处放大图Figure 5 Opening the front door and removing the back panel M10螺bolt栓3. 400kVA UPS Transportation Restraints Removing Procedures Installation hole coversOutput transformer A Bolt 2 pcs Transportation restraint A amplified viewFigure 9 Removing the two transportation restraints in the front Figure 10 Removing the two transportation restraints in the frontFigure 11 Removing the two transportation restraints at the back