Honeywell HRHD 410 specs

Configuration

Note You can upgrade the software only in the System Information

Change screen.

Only the System Administrator can upgrade the software.

You cannot upgrade the software during clip copy.

To upgrade the software:

a.Connect the USB device containing the upgrade package file to the DVR. Highlight Upgrade… and press # . The System Upgrade screen displays showing the upgrade package file name.

Note If no hard disk drives are installed in the DVR, the Upgrade… button will be disabled.

Note If the file system on the USB -IDE hard disk drive or USB flash drive is not FAT16 or FAT32 format, format the device using FAT16 or FAT32 format.

b.Select Start and then enter the Admin password to start the upgrade.

c.The system restarts automatically after the upgrade is complete. The software starts running after restarting the unit.

7.You can save your changes by highlighting OK and pressing # . Selecting Cancel exits the screen without saving the changes.

Rev 3.01	25	Document 900.0315
		10/05

Image 43

Honeywell HRHD 410 manual

Contents

Hrhd Revisions Issue Date Revisions FCC Compliance Statement Weee Waste Electrical and Electronic Equipment Explanation of Graphical Symbols Contents Operation Appendix a USB Hard Disk Drive Preparation Appendix C Solutions Appendix D Connector PinoutsAppendix B Text-In Query Examples Contents Rev Document 10/05 Figures 10/05 Figure F-1 Screen Map 101 Figures Rev Viii Document 10/05 Tables Tables Rev Document 10/05 About This Document Overview of Contents Important Safeguards Page Risk of explosion if battery is replaced by an incorrect Introduction Features Technical Overview Typical DVR InstallationPage Introduction Rev Document 10/05 Package Contents InstallationRequired Installation Tools Connecting the Loop Through Video Connecting the Video Source Audio In and Out Connectors Connecting Audio Cvbs Svhs VGA Switch Setting Unit for Cvbs Svhs or VGA Output Connecting the Spot Monitor Connecting the MonitorConnecting the RGB Monitor Connecting to the RS232C Port Connecting to the Network Port 10 Factory Reset Switch Factory Reset AI 1 to 4 Alarm Connecting AlarmsGND Ground ARI Alarm Reset Connecting to the RS485 PortAlarm Out Connecting the Power Cord Connecting to the USB Port Route power cords so they are not a tripping hazard Installation Rev Document 10/05 Front Panel Controls Configuration Mode, the REC LED flickers Power LED is lit when the DVR is OnFront Panel LEDs and Controls Front panel Function LEDs Up, Down, Left, Right Arrows Panic Front panel Function cont’d Shuttle Ring Turning on the PowerJog Dial Quick Setup Screen Initial Unit SetupPage System Information Normal Setup Screen System Information Change Screen Page Date/Time Screen Date/Time Setup Holiday Setup Screen Rev Document 10/05 11 System Check Screen System Check Screen 12 Storage Screen Storage Screen 13 S.M.A.R.T. Setup Screen System Shutdown System Log Screen Camera Setup Screen Configuring Input Devices 17 PTZ Device List Motion Detector Alarm In Setup Screen Menu choice Description Motion Detection Zone Choices 21 Text-In Setup Screen Text In Setup Screen 22 Text-In Generic Text Setup Screen 23 Text-In E-POS Setup Screen 24 Alarm Out Screen Alarm Out Setup Screen 26 Audio Setup Screen Audio Setup Screen 27 RS232/RS485 Screen RS232/RS485 Setup Screen Configuring Recording Settings 28 Record Mode Setup Screen Record Mode Setup ScreenPage 29 Time-Lapse Record Setup Screen Time-Lapse Record Mode Setup Screen 30 Time-Lapse Recording Schedule Screen Time-Lapse Recording Schedule 31 Pre-Event Recording Setup Screen Pre-Event Recording Setup Screen Alarm In Event Action Record Setup Screen Event Action Setup Alarm In Event Action Notify Setup Screen Alarm In Event Action Alarm Out Setup Screen 35 Motion Detector Event Action Record Setup Screen Motion Detector Event Action Record Setup Screen Motion Detector Event Action Notify Setup Screen Motion Detector Event Action Alarm Out Setup Screen 38 Text-In Event Action Record Screen Text-In Event Action Record Setup Screen Text-In Event Action Notify Setup Screen Text-In Event Action Alarm Out Setup Screen 41 Video Loss Event Action Record Screen Video Loss Event Action Record Setup Screen Video Loss Event Action Notify Setup Screen Video Loss Event Action Alarm Out Setup Screen OSD On-Screen Display Setup Display Setup 45 Main Monitoring Setup Screen Main Monitoring Setup Screen 46 Network Setup Screen Network Setup Screen 47 LAN Setup Screen LAN Setup Screen 48 Port Number Setup Screen LAN Dhcp LAN Adsl PPPoE 51 Modem Setup Screen Modem Setup 52 Dvrns Setup Screen Dvrns DVR Name Service Setup ScreenPage Callback Center Setup Screen Callback Center Setup by LAN Connections Callback Center Setup by Modem Connections 55 Password Setup Screen Password Setup Screen 56 Config Menu Config Configuration Menu 57 Clip Copy Screen Clip Copy 58 Disk Partition Selection Screen Clear All Data Load Default Setup Operation DVR Front Panel Live Monitoring Control buttons Function PTZ Mode Setting PTZ Presets Preset View Screen Digital Zoom Mode Recording Audio Recording Video Playback Text-In Screen Playing Recorded Video Right Arrow Playback ControlsPlayback Controls Press this button … To do this … Left Arrow Search Menu Searching Video Option Function Date/Time Search Event Search Calendar Search 13 Event Search by Event Screen 15 Text-In Log Screen Text-In SearchPage Preparing the USB-IDE Hard Disk Drive In Windows USB Hard Disk Drive Preparation Computer Text-In Query Examples Text-In Query Example 123456789012345678901234567890123456789012345678901234567890 Text-In Query Examples Rev Document 10/05 Problem Possible solution Solutions Solutions Rev Document 10/05 Connector Pinouts Connector Pinouts RS485 Connector Pinouts Table E-1 Technical Specifications Video SpecificationsInputs/Outputs Approval Table E-1 Technical Specifications ConnectorsStorage General Figure F-1 Screen Map Map of Screens Map of Screens Rev 102 Document 10/05 Index Page Page Page Page Video Systems Honeywell Security France Honeywell Security Germany