Alarm In Setup Screen, Motion Detector | Honeywell HRHD 410 specs

Configuration

Alarm In Setup Screen

The alarm terminal strip on the back of the DVR has inputs associated with each alarm. Use the Alarm In screen to configure each alarm input. Highlight Alarm In in the Device menu (MENU ➤ Device ➤ Alarm-In) and then press # . The Alarm In setup screen displays.

Figure 3-18 Alarm In Screen

You can turn each input On (via Alarm I/O or Camera Alarm) or Off. Each input can be given a title, and the inputs can be set as NO (normally open) or NC (normally closed) independently.

Motion Detector

Your DVR has a built-in video motion detector. Use the Motion Detector screen to turn video motion detection On or Off for each camera and to define the area of the image where you want to detect motion.

Highlight Motion Detector in the Device menu (MENU ➤ Device ➤ Motion Detector) and then press # . The Motion Detector setup screen displays.

Figure 3-19 Motion Detector Screen

Rev 3.01	35	Document 900.0315
		10/05

Image 53

Honeywell HRHD 410 manual Alarm In Setup Screen, Motion Detector

Contents

Hrhd Revisions Issue Date Revisions FCC Compliance Statement Weee Waste Electrical and Electronic Equipment Explanation of Graphical Symbols Contents Operation Appendix B Text-In Query Examples Appendix C Solutions Appendix D Connector PinoutsAppendix a USB Hard Disk Drive Preparation Contents Rev Document 10/05 Figures 10/05 Figure F-1 Screen Map 101 Figures Rev Viii Document 10/05 Tables Tables Rev Document 10/05 About This Document Overview of Contents Important Safeguards Page Risk of explosion if battery is replaced by an incorrect Introduction Features Technical Overview Typical DVR InstallationPage Introduction Rev Document 10/05 Required Installation Tools InstallationPackage Contents Connecting the Loop Through Video Connecting the Video Source Audio In and Out Connectors Connecting Audio Cvbs Svhs VGA Switch Setting Unit for Cvbs Svhs or VGA Output Connecting the RGB Monitor Connecting the MonitorConnecting the Spot Monitor Connecting to the RS232C Port Connecting to the Network Port 10 Factory Reset Switch Factory Reset GND Ground Connecting AlarmsAI 1 to 4 Alarm Alarm Out Connecting to the RS485 PortARI Alarm Reset Connecting the Power Cord Connecting to the USB Port Route power cords so they are not a tripping hazard Installation Rev Document 10/05 Front Panel Controls Configuration Front Panel LEDs and Controls Power LED is lit when the DVR is OnFront panel Function LEDs Mode, the REC LED flickers Up, Down, Left, Right Arrows Panic Jog Dial Turning on the PowerFront panel Function cont’d Shuttle Ring Quick Setup Screen Initial Unit SetupPage System Information Normal Setup Screen System Information Change Screen Page Date/Time Screen Date/Time Setup Holiday Setup Screen Rev Document 10/05 11 System Check Screen System Check Screen 12 Storage Screen Storage Screen 13 S.M.A.R.T. Setup Screen System Shutdown System Log Screen Camera Setup Screen Configuring Input Devices 17 PTZ Device List Motion Detector Alarm In Setup Screen Menu choice Description Motion Detection Zone Choices 21 Text-In Setup Screen Text In Setup Screen 22 Text-In Generic Text Setup Screen 23 Text-In E-POS Setup Screen 24 Alarm Out Screen Alarm Out Setup Screen 26 Audio Setup Screen Audio Setup Screen 27 RS232/RS485 Screen RS232/RS485 Setup Screen Configuring Recording Settings 28 Record Mode Setup Screen Record Mode Setup ScreenPage 29 Time-Lapse Record Setup Screen Time-Lapse Record Mode Setup Screen 30 Time-Lapse Recording Schedule Screen Time-Lapse Recording Schedule 31 Pre-Event Recording Setup Screen Pre-Event Recording Setup Screen Alarm In Event Action Record Setup Screen Event Action Setup Alarm In Event Action Notify Setup Screen Alarm In Event Action Alarm Out Setup Screen 35 Motion Detector Event Action Record Setup Screen Motion Detector Event Action Record Setup Screen Motion Detector Event Action Notify Setup Screen Motion Detector Event Action Alarm Out Setup Screen 38 Text-In Event Action Record Screen Text-In Event Action Record Setup Screen Text-In Event Action Notify Setup Screen Text-In Event Action Alarm Out Setup Screen 41 Video Loss Event Action Record Screen Video Loss Event Action Record Setup Screen Video Loss Event Action Notify Setup Screen Video Loss Event Action Alarm Out Setup Screen OSD On-Screen Display Setup Display Setup 45 Main Monitoring Setup Screen Main Monitoring Setup Screen 46 Network Setup Screen Network Setup Screen 47 LAN Setup Screen LAN Setup Screen 48 Port Number Setup Screen LAN Dhcp LAN Adsl PPPoE 51 Modem Setup Screen Modem Setup 52 Dvrns Setup Screen Dvrns DVR Name Service Setup ScreenPage Callback Center Setup Screen Callback Center Setup by LAN Connections Callback Center Setup by Modem Connections 55 Password Setup Screen Password Setup Screen 56 Config Menu Config Configuration Menu 57 Clip Copy Screen Clip Copy 58 Disk Partition Selection Screen Clear All Data Load Default Setup Operation DVR Front Panel Live Monitoring Control buttons Function PTZ Mode Setting PTZ Presets Preset View Screen Digital Zoom Mode Recording Audio Recording Video Playback Text-In Screen Playing Recorded Video Playback Controls Playback ControlsPress this button … To do this … Left Arrow Right Arrow Search Menu Searching Video Option Function Date/Time Search Event Search Calendar Search 13 Event Search by Event Screen 15 Text-In Log Screen Text-In SearchPage Preparing the USB-IDE Hard Disk Drive In Windows USB Hard Disk Drive Preparation Computer Text-In Query Examples Text-In Query Example 123456789012345678901234567890123456789012345678901234567890 Text-In Query Examples Rev Document 10/05 Problem Possible solution Solutions Solutions Rev Document 10/05 Connector Pinouts Connector Pinouts RS485 Connector Pinouts Inputs/Outputs SpecificationsTable E-1 Technical Specifications Video Storage Table E-1 Technical Specifications ConnectorsGeneral Approval Figure F-1 Screen Map Map of Screens Map of Screens Rev 102 Document 10/05 Index Page Page Page Page Video Systems Honeywell Security France Honeywell Security Germany