Electro-Mechanical Parking Brake Testing | Invacare M61, M50, M51

SECTION 12—MOTORS

WARNING

A shorted electro-mechanical brake will damage the brake output section in the controller. DO NOT connect a shorted electro-mechanical brake to a good controller module. A shorted brake MUST be replaced.

NOTE: A bad motor can damage the controller module but a bad controller will NOT damage a motor.

.

Cap

Motor

4 Pin Motor

Connector

FIGURE 12.5 Electro-Mechanical Parking Brake Testing

Part No. 1125075

119

Pronto® Series

Image 119

Invacare M61, M50, M51 service manual Electro-Mechanical Parking Brake Testing

Contents

Pronto Series M50 M51 M61 Document Part Number Recommended ToolsReference Documents Recommended Tools Table of Contents Asba Seat ArmsVAN Seat Shrouds and Frame Front RIGGINGS/FOOTBOARDWheels Motors Batteries Electronics AccessoriesLimited Warranty Wheelchair TIE-DOWN Restraints and Seat Restraints Signal Word MeaningSpecial Notes Special Notes Label Location Asba Typical Product ParametersMedium SEMI-RECLINE Typical Product Parameters Medium Operation Information Controller Settings/Repair or ServiceGeneral Guidelines Immediately Tire PressureBatteries Charging Batteries Grounding Instructions Rain Test Weight TrainingWeight Limitation EMI Information EMI Information EMI Information All Wheelchairs Safety INSPECTION/TROUBLESHOOTINGSafety Inspection Checklists Wheels TroubleshootingSolutions Additional Requirements for M61 Wheelchairs Comments Display Description Definition SPJ Information Gauge Display Diagnostics SUB Code Diagnostic CodesDiagnostics Code Possible Solution E05 Motor/Gearbox/Brake Symptom Probable Cause Solutions Contamination is found. Refer to Replacing Motor Battery Battery Charger DON’T Checking Battery Charge LevelM61 Only Field Load Test Battery Quality Motor Testing M50 and M51 Wheelchairs Manufactured Before 8/15/05 Turning the Power On/OffWheelchair Operation Turn the power On by pressing the On/Off button Using the Joystick to Drive the Wheelchair Reverse Movement Action Adjusting the Speed Using the Horn M50 M51 Wheelchairs Manufactured Before 15/05 Using the Horn M50/M51 Wheelchairs Manufactured After 8/14/05 and All M61 Elevating the Seat Elevating the Seat Joystick SPJJoystick Switches and IndicatorsOn/Off Toggle Switch Speed Control Knob Information Gauge Display Mode Button SPJ+ and SPJ+ w/ACC Joystick Switches and Indicators Speed Control Buttons Mode ButtonOn/Off Button Speedometer Service Indicator Arms Removing/Installing Van Seat ArmAdjusting Van Seat Arm Width Adjusting Van Seat Arm Height Adjustable Height Arms Only Adjusting Van Seat Arm Angle Adjusting Van Seat Arm Height Adjustable Height Arms Only Replacing Van Seat Armrest Assembly Removing/Installing Flip Back Armrest Removing/Installing Flip Back Armrest Adjusting the Flip Back Armrest Height Adjusting the Flip Back Armrest Height Fold Down Back Angle Adjusting the Back AngleVAN Seat Semi-Recline Back Angle Removing Adjusting the Headrest Semi-Recline OnlyRemoving/Installing the Seat Assembly Installing Removing/Installing the Seat Assembly Adjusting Seat Depth Adjusting Seat Depth M50/M51 Wheelchairs Adjusting the Seat Height Sets of Seat Total Number Length of Mounting M61 Wheelchairs Adjusting the Seat Height M61 Wheelchairs Adjusting Seat Position on Seat Base Seat Position Weight Seat Post Inch Standard Limitation Mounting Hole Replacing the Seat Positioning Strap Replacing the Seat Positioning Strap Asba Seat M50/51 Wheelchairs Only Adjusting the Seat Height M50/51 Wheelchairs Only Weight Seat Post Seat Depth Limitation Mounting Hole Inch M61 Wheelchairs Removing/Installing the Seat Pan Removing/Installing the Seat Frame Adjusting the Seat Width Removing/Installing the Seat Frame Adjusting the Seat Position Adjusting the Seat Position Removing/Installing the Seat Positioning Strap Height, only new back canes will be needed Back Upholstery Asba Seat Asba Seat Height Back Height Adjusting the Back Angle Adjusting the Back Angle Front RIGGINGS/ Footboard Installing/Removing Front Riggings Model PHWH93 Front Riggings Adjusting Footrest Height Model PH904A and PHAL4A Front Riggings Replacing Heel Loops Van Seats Adjusting/Replacing Telescoping Front Rigging SupportsRaising/Lowering Elevating Front Riggings Position Asba SeatFront Rigging Standard Inch OUT Inches OUT Removing/Installing the Footboard Assembly Angle Adjusting the Footboard Assembly Depth Adjusting the Footboard Assembly Angle Replacing the Front/Rear Casters Wheels Adjusting Caster Assembly Adjusting Caster Assembly Removing/Installing the Front Headtube Assembly Removing/Installing the Front/Rear Caster Assemblies Removing the Drive Wheel Removing/Installing the Drive WheelInstalling the Drive Wheel Removing/Installing the Drive Wheel Inner Rim Shrouds and Frame Removing/Installing the Top Shroud Removing/Installing the Top Shroud Removing/Installing the Side Shrouds Removing/Installing the Side Shrouds Removing/Installing the Front Shroud Removing/Installing the Front Shroud Removing/Installing the Inner Shrouds Removing/Installing the Inner Shrouds Removing/Installing the Pivot Tube Removing/Installing the Pivot Tube Removing/Installing the Walking Beam Removing/Installing the SureStep Spring Removing/Installing the Walking Beam Removing/Installing the Elevate Actuator Installing Removing/Installing the Elevate Actuator Removing/Installing the Actuator Switch Sensor Batteries Removing/Installing Batteries from/into Battery Tray Using the Proper Batteries Batteries Tool QTY Comments Connecting Battery Cables Connecting/Disconnecting Battery Cables 102 Connecting/Disconnecting Battery Cables Charging Batteries Disconnecting Battery Cables Battery Charger Operation On-Board Battery Charger Charging Indicator Status ON/OFF Indicator Status Replacing the On-Board Battery Charger Fuse Replacing the On-Board Battery Charger Fuse Replacing the On-Board Battery Charger 110 Replacing the On-Board Battery Charger Motors Removing/Installing the Motor Removing/Installing the Motor Engaging/Disengaging Motor Release Lever Engaging/Disengaging Motor Release Lever Removing/Installing the Motor Release Lever Removing/Installing the Motor Release Lever Replacing Motor Brushes 117 Replacing Motor Brushes Electro-Mechanical Parking Brake Testing Electro-Mechanical Parking Brake Testing Electronics Removing/Installing the Joystick Van Seat Repositioning the Joystick Mounting Bracket Repositioning the Joystick Mounting Bracket Connecting Disconnecting/Connecting the JoystickDisconnecting Adjusting Lock/Release Tension Adjusting the Quad-Link Retractable Mount Replacing the Controller Adjusting Lock/Release Tension Replacing the Controller Wire Routing Wire Routing Installing/Removing the Crutch/Cane Holder Accessories Holder Installing/Removing the Oxygen Holder Using the Walker Holder Installing/Removing/Using the Walker HolderInstalling/Removing the Walker Holder 131 Limited Warranty USA