Channel Channel Dolby | JBL 201, SDP-5, Home Theater System specification

SDP-5

MODE ADJUST

The table below indicates the conditions in which Dolby Digital Surround EX decoding is engaged.

•Dolby Digital Surround EX decoding is engaged when the EX DECODING parameter is set to ON, or the EX DECODING parameter is set to AUTO and a flagged 5.1-channel Dolby Digital source recorded with Dolby Digital Surround EX is detected.

•Dolby Digital Surround EX decoding is not engaged when the EX DECODING parameter is set to OFF, or the EX DECODING parameter is set to AUTO and a non-flagged 5.1-channel Dolby Digital source recorded without or without Dolby Digital Surround EX is detected.

•Listening mode name differs depending on the encoding present in the input source, the EX DECODING parameter setting, and the speaker setup.

–The DOLBY DIGITAL EX listening mode is available when Dolby Digital Surround EX decoding is engaged.

–The DOLBY DIGITAL listening mode is available when Dolby Digital Surround EX decoding is not engaged.

–The DOLBY DIGITAL EX listening mode cannot be activated unless both side and rear speakers are present.

Note:

The SDP-5 cannot automatically detect Dolby Digital Surround EX encoding in non-flagged 5.1-channel Dolby Digital sources. A non-flagged source does not include information in the input signal that identifies Dolby Digital Surround EX encoding.

		Input	5.1-Channel	5.1-Channel Dolby	5.1-Channel Dolby
	Parameter	Source	5.1-Channel	5.1-Channel Dolby	5.1-Channel Dolby
		Source	Dolby Digital	Digital EX (Flagged)	Digital EX (Non-Flagged)

	Setting

	EX DECODING: AUTO		DOLBY DIGITAL	DOLBY DIGITAL EX	DOLBY DIGITAL

	EX DECODING: ON		DOLBY DIGITAL EX	DOLBY DIGITAL EX	DOLBY DIGITAL EX

	EX DECODING: OFF		DOLBY DIGITAL	DOLBY DIGITAL	DOLBY DIGITAL

5-19

Image 122

JBL 201, SDP-5, Home Theater System manual Channel Channel Dolby, Dolby Digital Digital EX Flagged Digital EX Non-Flagged

Contents

JBL SIS Products Group Introduction Getting Started SetupIntroduction Basic Operation Audio Controls Mode AdjustTroubleshooting & Maintenance Appendix English Important Safety Instructions Español Instrucciones DE Seguridad Importantes Importanti Norme DI Sicurezza Dansk Vigtig Information OM Sikkerhed Norsk Viktig Informasjon OM Sikkerhet ES Desembalaje e inspección US Unpacking and InspectionDE Auspacken und Überprüfung FR Contenu de l’emballage et inspection Getting Started Getting Started About the SDP-5 Highlights Installation Considerations Do Not Remote Control Battery Installation To replace the remote control batteries Basic Operation Front Panel Display Front Panel OverviewStandby Button To use the volume knob to adjust Main Zone volume level Volume KnobMode and Buttons To use the volume knob to adjust Zone 2 volume level Main Zone Off Button Mute ButtonMain Zone Input Selection Buttons Zone 2 Input Selection Buttons Digital Audio Input Connectors S/PDIF Power SwitchAC Input Connector Digital Audio Output Connector S/PDIF Zone 2 Audio Output Connectors Rear Panel Overview from Zone 2 Video Output Connectors Video Input ConnectorsMain Zone Video Output Connectors RS-232 Connectors Operation Considerations Remote Control OverviewMain Menu Menu Navigation Parameter Drop-Down Menus Arrow Navigation FunctionsMenu Options Menu Parameters Horizontal Bar Graphs To select the desired setting on a parameter drop-down menuTo adjust a parameter setting with a horizontal bar graph To activate the Zone 2 or Shift command bank Command Bank ActivationCommand Matrix Button Main Zone Shift Scroll upward Increase Decrease Adjust the Audio DVD2 Basic Operation Shift-THX Shift-DOLBYShift-dts Understanding the Zones Zone 2 Two-Line Status TWO-LINE StatusMain Zone Two-Line Status Status Menus Status menus Dolby D Status Parameter Possible Settings2CH Status Dts-ES Status 1a Bypass Status 2CH Bypass Status Digital Status Center MIX LVL EncodingBIT Rate Channels MIX Room InputInput Type Mode Basic Operation Setup Displays Rear Panel ConfigVolume Controls Inputs Input Setup Lock Options To customize the name of the selected input Changing Input Names NameEdit Input Name Restore Default Name To restore the factory-default name of the selected input Assigning Audio & Video Input Connectors Please note the following DigitalCOAX-1 to 4, OPTICAL-1 to 4, None Assigning Audio & Video Input Connectors from Anlg in LVL Auto 18 to +12dB ManualAuto Gain COMPOSITE-1 to 5, S-VIDEO-1 to 5, None Level MetersVideo Component Selecting Preferred Listening Modes When the 2-CH parameter is set to USE Last Selecting Preferred Listening Modes from When the Dolby D parameter is set to USE Last Dolby D When the dts-ES parameter is set to USE Last Dts-ES Configuring Advanced Zone Settings Main Advanced Input Select Input Select Parameter Settings Digital Analog Auto CH Anlg BYP ON, OFF Video Video OSD Component OSD ZONE2 DIGITAL, ANLG, Dmix Anlg Analog Dmix Downmix ZONE2 in Parameter SettingsDigital Determining Crossover Points Speaker SetupCustom Speaker Setups Highpass Filter FULL, 30Hz to 120Hz, THX 80Hz Default Possible Parameter Setting SettingsFront L/R Center FULL, 30Hz to 120Hz, THX 80Hz, None Side L/R Rear L/R Subwoofer THX ULTRA2 SUB BGC Boundary Gain Compensation ASA Advanced Speaker Array Synthesis 7-CHANNEL Speaker Setups THX ULTRA2 SUB OFF ON, OFF BGC ASA Apart JBL Synthesis 7-Channel Speaker Setups from THX 80Hz, None Measuring Speaker Distances Rear Left & Right Measuring Speaker Distances fromSide Left & Right Units Calibrating Output Levels Internal Noise Test Internal Noise Test from Sources Dacs CalibrationChannel Dolby Digital Dts-ES Front Left & Right 18.0 to +12.0dB Subwoofer Side Left & RightRear Left & Right Bass Peak Limiter CAL Noise 75 to 120dB SUB LimiterSUB Limit ADJ ST. & 1 5.1 Anlg Rear Panel ConfigStereo Inputs ST. & 2 5.1 Anlg Display Setup Sync Delay Edit Custom Name To customize the name of the SDP-5 ON-SCREEN Display Setup Status Position Format Background Remote State Brightness Front Panel Display SetupStatus 100%, 75%, 50%, 25% Mute Level Volume Control SetupMain PWR on Zone PWR on Be used to configure the trigger output connector Selecting the Setup menu Trigger option opensTrigger Setup menu shown at the right, which can Program Operation Parameters ON, OFF Audio Cntrl Lock OptionsModes Setup Audio Controls Bass Default Possible Parameter Value SettingsAudio Controls Treble Bass Parameter Settings Treble Parameter Settings To +3.0dB Tilt EQLoudness Tilt EQ Parameter Settings Loudness Parameter Settings ZONE2 Balance BalanceFader To to R Mode Adjust Listening modes can be activated with Mode AdjustListening Mode Activation Mode Family Selection Buttons Preferred Listening Mode Selection ParametersMode and Buttons Listening Mode Descriptions L7 TV Option Default Possible Parameter Setting SettingsL7 Film L7 Music L7 Music Surr Dolby Plii + THX Option DefaultParameter Setting Settings Dolby Plii Movie Option Parameter Dolby Plii MusicDolby PRO Logic Dts NEO6 Film Dts NEO6 Music Nightclub Concert Hall Church Cathedral Panorama Calibration To calibrate the Panorama listening modePanorama Listener POS Speaker AngleSource +0dB OFF, -30 to +12dB PartyChannel Mono Mono LogicMono Surround L7 Film L7 TV L7 Music THX, 5.1 THX ULTRA2, & 5.1 THX SurEX Channel Channel Surround EX-Encoded THX SurEX THX Music Dolby Digital & Dolby Digital EX Channel Channel Dolby Dolby Digital Digital EX Flagged Digital EX Non-Flagged 2-CHANNEL Mono Surr Mono Dts Dts-ES DecodingChannel dts Dts-ES L7 Film Dts-ES L7 Music Dts THX ULTRA2 & dts-ES THX Dts THX Music +0.0dB 10.0 to +0.0dB Dts-ES Dts-ES 2-CHAN 1a Bypass 2CH Bypass Academy Filter Bass ContentSpkr Enhance Auto Azimuth Center Depth Bass RTCalibration Center MIX Dimension Listening Mode Menu Option & Parameter DescriptionsCustom VS Preset Effect LVL Input Balance EX DecodingFront Steering Output Levels Panorama PRE-DELAYReset Mode RE-EQUALIZER Rolloff Reset ModeSize Sound Stage Surr Rolloff Speech DetectSUB Level Surround DLY Vocal Enhance Surround EXSurround MIX Troubleshooting & Maintenance Troubleshooting RF interference is present in the audio or video SDP-5 is powered on, but there is no videoRoutine Maintenance SDP-5 is exhibiting erratic behavior Restoring FACTORY-DEFAULT Settings To restore factory-default settings Appendix Main Zone Audio Performance SpecificationsAudio Input & Output Connectors Zone 2 Audio Performance Composite & S-video Performance Specifications are subject to change without noticeVideo Input & Output Connectors Component Video Performance Declaration of Conformity Menu Tree Input Setup DVD1 DVD2 SAT VCR Tuner AUX JBL None DVD1 Component Menu Tree from page A-7 Are automatically set Menu Tree from page A-9 Party Output Levels Custom Channel SUB Level Menu Tree from page A-11 Surround DLY Installation Worksheet Input Setup DVD1 DVD2 SAT VCR Tuner AUX Settings Setup Display SetupVolume Control Trigger Setup