Manuals / Konica Minolta / Computer Equipment / Printer

Konica Minolta 752 operation manual Calibrating Density CALIBRATION

Models: 752

1 87

Download 87 pages 20.91 Kb

Page 36

"Calibrating Density (CALIBRATION)

4-3.How To Operate Maintenance Mode

"Calibrating Density (CALIBRATION)

The device has the densitometer in the cooling/discharge section, which allows you to control the density automatically.

If there is a problem with the density, print the calibration sheet from this screen to calibrate the density.

•Calibration

(1)Touch [CALIBRATION] on the maintenance menu screen.

The message for selecting the tray will appear.

(2)Touch the key of the tray for which you wish to per- form density correction.

The print data in the calibration sheet will be queued, and the maintenance menu screen will re-appear.

If you wish to perform density correction for the other tray, repeat from Step (1).

(3)Touch [EXIT] to end the maintenance mode.

When the normal screen re-appears, the ﬁlm in the selected tray is transported and the calibration sheet is printed out. Wait until printing is complete. After printing is end, the density cor- rection is complete.

IMPORTANT

•The calibration sheet is used as the sampling data (the data before the density correction) for the automatic density correction.

When you check and control the density, use the SMPTE pattern which is printed out by TEST PRINT on the maintenance menu. (Refer to page 26.)

24 DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6

Image 36

Konica Minolta 752 operation manual Calibrating Density CALIBRATION

Contents

DRYPRO model LASER IMAGERCODE NO 0463 UL, 0467 CE KONICACORPORATIONBlank page DRY LASER IMAGER DRYPRO MODEL Table of ContentsIntroduction Descriptions of Symbol Mark Symbol markDescriptions of symbol mark Descriptions on Warning Label Descriptions on warning caution labelWarning Label Warning Label Location 1 Front2 Rear Safety Caution Cautions on installationCautions on transporting, storing temporally, and servicing Cautions on use otherwise, dust may be accumulated, resulting in heating or a ﬁre Precaution Disposal PrecautionPrecaution on Installation Location Control panel Start switch Upper tray Lower tray Front cover 1. Name of Each Component1-1. Main Body Front ViewPower connector Power cableRear View Air outlet1-2. Sorter LiS-752 option Bins Inlet guide Sorter left cover Front cover2. Structure 3. How To Operate 3-1. Control PanelDescription on screen Start switch 3-2. Start-up OperationBreaker Power saving mode Touch WAKE UP on the control panel3-3. Shut-down Operation When START TIMER is set to ON Press the start switch to re-start the equip- ment 3-4. Film Loading 3-4.Film LoadingFilm loading screen Empty package SealsBarcode Retaining plate9 Push the tray to the back until it is locked Load the ﬁlm by referring to Steps 2 or later 4. Maintenance Mode 4-1. Function of Maintenance Mode4-2. Switching Maintenance Mode Start-up maintenance modeShut-down maintenance mode 4-3. How To Operate Maintenance Mode Setting START TIMER FunctionSetting Date/Time TIME SET Re-printing Printed Page PREVIOUS PRINT The print data on the speciﬁed page will be queued 8 Touch a LUT name you wish to apply for printing 9 Touch on the upper part of the screen11 Select NEGA/POSI by touching NEGA or POSI Calibrating Density CALIBRATION The DRYPRO has the automatic density calibration function that perform the density calibration automatically after a lapse of the speciﬁed time or speciﬁed number of printing. Instead of performing automatic calibration, you can make CALIBRA- TION appear on the screen to show you that the calibration needs performing depending on the settings at installation TEST PRINT 5 Touch on the upper part of the screen 14 Touch EXIT to end the maintenance mode 4-3.How To Operate Maintenance Mode9 Select NEGA/POSI by touching NEGA or POSI 10 Touch on the upper part of the screenEach frame of the SMPTE pattern for this device which is printed out by TEST PRINT consists of 16-step wedge, SMPTE pattern, and 1024-step gray scale. Measure the density of the 16-step wedge or SMPTE pattern and use it for the density control Opening/closing front cover COVER OPEN Adjusting control panel PANEL ADJUST The PANEL ADJUST screen will appearThe maintenance menu screen will re-appear The touch position adjustment screen will appear3 Touch OK Clearing queued print data QUEUE CLEAR 4 Touch OK on the conﬁrm message COLD START The COLD START function re-starts the deviceConﬁrming and setting ﬁlm count data 1 Touch FILM DATA on the maintenance menu screenConﬁrming ﬁlm count data month, touch MONTHLYFollow the procedure below to set the ﬁlm count preferences The FILM DATA SETUP screen will appearThe setting becomes valid, and the ﬁlm count data screen re- appears If you wish to cancel the settings, touch CANCELSetting print preference Sets the bin in the sorter option into which the 12 Select the item to be printed as the stamp with STAMP SELECT 16 Sets the format of date to be printed on the ﬁlm Setting user LUT 4-3.How To Operate Maintenance Mode1 Touch the user LUT name to be set on the LUT select screen 2 Touch LUT LIBRARYCreating user LUT 8 After the settings are complete, touch OK 4-3.How To Operate Maintenance Mode6 Touch EDIT on the LUT data screen Conﬁrming the LUT curveSetting power saving mode 6 After the settings are complete, touch OK 4-3.How To Operate Maintenance Mode5. Troubleshooting 5-1. Error Display and Remedypage pagePage 5-2. Resetting Errors 5-2.Resetting ErrorsWhen an error cannot be reset If ERROR RESET cannot function by clearing a queued error, follow the procedure below to re-start the device 5-3. Removing Jam When TRAY OPEN is displayedWhen COVER OPEN is displayed When SORTER COVER is displayedJam in tray Film jam between decent transport section and exposure section Film jam between exposure section and elevator transport section Green leverCaution on High Temperatures Film jam between HPRO section and cooling/discharge sectionCaution on High Temperatures Film jam in sorter 1 Open the inlet guide, and remove jammed ﬁlms if there are any58 DRYPRO MODEL 752 Operation Manual Ver.0.11 3 Remove jammed ﬁlms if they remain 4 Lift the handle of the sorter left cover to remove it5 Open the ﬁlm transport guide, and remove jammed ﬁlms if they remain Sorter left coverGuide pins 6 Put the ﬁlm transport guide back, and remove the sorter left coverFilm transport guide lower5-4. When Film Fails to be Loaded 5-4.When Film Fails to be LoadedRail 5 Open the light shield cover of the tray 14 Touch OK 15 Touch EXIT to end the maintenance mode 5-4.When Film Fails to be Loaded13 Touch the key of the tray in which you wish to re- load the ﬁlm 17 When the tray pops out slightly, press in it until it locks 16 Touch FILM SET6. Service and Maintenance 6-1. Periodical Maintenance and InspectionOuter cover of the main unit Inside of main unit6-2. Replacing FILTER Caution on High Temperatures6-3. Service and Maintenance Schedule Other service and maintenanceServicing by a user Conﬁrming maintenance and maintenance display 7. Speciﬁcations When connected to the RegiusWhen connected to any other than the RegiusSorter Option Speciﬁcations Appendix Time zone and code No. table1.Handling and Storage of Unexposed Film 2.Handling and Storage of Developed FilmHANDLING AND STORAGE OF DRY FILM Blank page Blank page