KONICACORPORATION
DRYPRO model
LASER IMAGER
CODE NO 0463 UL, 0467 CE
Blank page
Table of Contents
DRY LASER IMAGER DRYPRO MODEL
Introduction
Descriptions of Symbol Mark
Symbol mark
Descriptions of symbol mark
Descriptions on warning caution label
Descriptions on Warning Label
Warning Label
Warning Label Location
1 Front
2 Rear
Safety Caution
Cautions on installation
Cautions on transporting, storing temporally, and servicing
Cautions on use
otherwise, dust may be accumulated, resulting in heating or a fire
Precaution
Disposal Precaution
Precaution on Installation Location
Front View
Control panel Start switch Upper tray Lower tray Front cover
1. Name of Each Component
1-1. Main Body
Air outlet
Power connector
Power cable
Rear View
Bins Inlet guide Sorter left cover Front cover
1-2. Sorter LiS-752 option
2. Structure
3. How To Operate
3-1. Control Panel
Description on screen
Start switch
3-2. Start-up Operation
Breaker
Touch WAKE UP on the control panel
Power saving mode
3-3. Shut-down Operation
When START TIMER is set to ON
Press the start switch to re-start the equip- ment
3-4.Film Loading
3-4. Film Loading
Film loading screen
Retaining plate
Empty package
Seals
Barcode
9 Push the tray to the back until it is locked
Load the film by referring to Steps 2 or later
4-1. Function of Maintenance Mode
4. Maintenance Mode
4-2. Switching Maintenance Mode
Start-up maintenance mode
Shut-down maintenance mode
Setting START TIMER Function
4-3. How To Operate Maintenance Mode
Setting Date/Time TIME SET
Re-printing Printed Page PREVIOUS PRINT
The print data on the specified page will be queued
9 Touch on the upper part of the screen
8 Touch a LUT name you wish to apply for printing
11 Select NEGA/POSI by touching NEGA or POSI
Calibrating Density CALIBRATION
The DRYPRO has the automatic density calibration function that perform the density calibration automatically after a lapse of the specified time or specified number of printing. Instead of performing automatic calibration, you can make CALIBRA- TION appear on the screen to show you that the calibration needs performing depending on the settings at installation
TEST PRINT
5 Touch on the upper part of the screen
10 Touch on the upper part of the screen
14 Touch EXIT to end the maintenance mode
4-3.How To Operate Maintenance Mode
9 Select NEGA/POSI by touching NEGA or POSI
Each frame of the SMPTE pattern for this device which is printed out by TEST PRINT consists of 16-step wedge, SMPTE pattern, and 1024-step gray scale. Measure the density of the 16-step wedge or SMPTE pattern and use it for the density control
Opening/closing front cover COVER OPEN
The touch position adjustment screen will appear
Adjusting control panel PANEL ADJUST
The PANEL ADJUST screen will appear
The maintenance menu screen will re-appear
3 Touch OK
Clearing queued print data QUEUE CLEAR
4 Touch OK on the confirm message
The COLD START function re-starts the device
COLD START
month, touch MONTHLY
Confirming and setting film count data
1 Touch FILM DATA on the maintenance menu screen
Confirming film count data
If you wish to cancel the settings, touch CANCEL
Follow the procedure below to set the film count preferences
The FILM DATA SETUP screen will appear
The setting becomes valid, and the film count data screen re- appears
Setting print preference
Sets the bin in the sorter option into which the
12 Select the item to be printed as the stamp with STAMP SELECT
16 Sets the format of date to be printed on the film
2 Touch LUT LIBRARY
Setting user LUT
4-3.How To Operate Maintenance Mode
1 Touch the user LUT name to be set on the LUT select screen
Creating user LUT
Confirming the LUT curve
8 After the settings are complete, touch OK
4-3.How To Operate Maintenance Mode
6 Touch EDIT on the LUT data screen
Setting power saving mode
4-3.How To Operate Maintenance Mode
6 After the settings are complete, touch OK
page
5. Troubleshooting
5-1. Error Display and Remedy
page
Page
5-2.Resetting Errors
5-2. Resetting Errors
When an error cannot be reset
If ERROR RESET cannot function by clearing a queued error, follow the procedure below to re-start the device
When SORTER COVER is displayed
5-3. Removing Jam
When TRAY OPEN is displayed
When COVER OPEN is displayed
Jam in tray
Film jam between decent transport section and exposure section
Green lever
Film jam between exposure section and elevator transport section
Film jam between HPRO section and cooling/discharge section
Caution on High Temperatures
Caution on High Temperatures
Film jam in sorter
1 Open the inlet guide, and remove jammed films if there are any
58 DRYPRO MODEL 752 Operation Manual Ver.0.11
Sorter left cover
3 Remove jammed films if they remain
4 Lift the handle of the sorter left cover to remove it
5 Open the film transport guide, and remove jammed films if they remain
lower
Guide pins
6 Put the film transport guide back, and remove the sorter left cover
Film transport guide
5-4. When Film Fails to be Loaded
5-4.When Film Fails to be Loaded
Rail
5 Open the light shield cover of the tray
14 Touch OK 15 Touch EXIT to end the maintenance mode
5-4.When Film Fails to be Loaded
13 Touch the key of the tray in which you wish to re- load the film
16 Touch FILM SET
17 When the tray pops out slightly, press in it until it locks
Inside of main unit
6. Service and Maintenance
6-1. Periodical Maintenance and Inspection
Outer cover of the main unit
Caution on High Temperatures
6-2. Replacing FILTER
6-3. Service and Maintenance Schedule
Other service and maintenance
Servicing by a user
Confirming maintenance and maintenance display
the Regius
7. Specifications
When connected to the Regius
When connected to any other than
Sorter Option Specifications
Time zone and code No. table
Appendix
1.Handling and Storage of Unexposed Film
2.Handling and Storage of Developed Film
HANDLING AND STORAGE OF DRY FILM
Blank page
Blank page