Manuals / Konica Minolta / Computer Equipment / Printer

Konica Minolta 752 operation manual Sets the bin in the sorter option into which the

Models: 752

1 87

Download 87 pages 20.91 Kb

Page 51

: Sets the bin in the sorter (option) into which the

4-3.How To Operate Maintenance Mode

(6)Touch the key on the right of the setting item, then touch [$] / [%] on the lower part of the screen to set the following items.

DENSITY	: Adjust the density of an image.
	Selectable from -7 to 7.
	Setting a negative value will make the den-
	sity lighter, and a positive value, darker.
CONTRAST	: Adjust the contrast of an image.
	Selectable from -7 to 7.
	Setting a negative value will make the con-
	trast lower, and a positive value, higher.
SMOOTH TYPE : Sets the smoothing type of an image.

SMOOTH TYPE		Settings

OFF		Does not perform the magniﬁcation
		interpolation.

1		Performs the Biliner interpolation.

2-6		Performs the Cubic Spline interpo-
		lation.
		Increasing the value will smooth an
		image greater.

7Does not perform the magniﬁcation interpolation. But prints out in the MAGNIFICATION setting. When you wish to change this setting, ask a service person.

DEFAULT TRAY: Sets whether the upper or lower tray is pri- oritized when the tray is not speciﬁed from the diagnostic device.

(7)After the settings are complete, touch on the upper part of the screen once.

The print preference set screen (3/7) will appear.

(8)Touch the key on the right of the setting item, then touch the numeric keys on the lower part of the screen to set the following items.

MAX DENSITY : Sets the maximum density of an image.

MIN DENSITY	: Sets the minimum density of an image.
Lo	: (Not used for the current version.)
La	: (Not used for the current version.)
SORTER	: Sets the bin in the sorter (option) into which the
	ﬁlm is discharged.

(9)After the settings are complete, touch on the upper part of the screen once.

The print preference set screen (4/7) will appear.

DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6 39

Image 51

Konica Minolta 752 operation manual Sets the bin in the sorter option into which the

Contents

KONICACORPORATION DRYPRO modelLASER IMAGER CODE NO 0463 UL, 0467 CEBlank page Table of Contents DRY LASER IMAGER DRYPRO MODELIntroduction Descriptions of Symbol Mark Symbol markDescriptions of symbol mark Descriptions on warning caution label Descriptions on Warning LabelWarning Label Warning Label Location 1 Front2 Rear Safety Caution Cautions on installationCautions on transporting, storing temporally, and servicing Cautions on use otherwise, dust may be accumulated, resulting in heating or a ﬁre Precaution Disposal PrecautionPrecaution on Installation Location Front View Control panel Start switch Upper tray Lower tray Front cover1. Name of Each Component 1-1. Main BodyAir outlet Power connectorPower cable Rear ViewBins Inlet guide Sorter left cover Front cover 1-2. Sorter LiS-752 option2. Structure 3. How To Operate 3-1. Control PanelDescription on screen Start switch 3-2. Start-up OperationBreaker Touch WAKE UP on the control panel Power saving mode3-3. Shut-down Operation When START TIMER is set to ON Press the start switch to re-start the equip- ment 3-4.Film Loading 3-4. Film LoadingFilm loading screen Retaining plate Empty packageSeals Barcode9 Push the tray to the back until it is locked Load the ﬁlm by referring to Steps 2 or later 4-1. Function of Maintenance Mode 4. Maintenance Mode4-2. Switching Maintenance Mode Start-up maintenance modeShut-down maintenance mode Setting START TIMER Function 4-3. How To Operate Maintenance ModeSetting Date/Time TIME SET Re-printing Printed Page PREVIOUS PRINT The print data on the speciﬁed page will be queued 9 Touch on the upper part of the screen 8 Touch a LUT name you wish to apply for printing11 Select NEGA/POSI by touching NEGA or POSI Calibrating Density CALIBRATION The DRYPRO has the automatic density calibration function that perform the density calibration automatically after a lapse of the speciﬁed time or speciﬁed number of printing. Instead of performing automatic calibration, you can make CALIBRA- TION appear on the screen to show you that the calibration needs performing depending on the settings at installation TEST PRINT 5 Touch on the upper part of the screen 10 Touch on the upper part of the screen 14 Touch EXIT to end the maintenance mode4-3.How To Operate Maintenance Mode 9 Select NEGA/POSI by touching NEGA or POSIEach frame of the SMPTE pattern for this device which is printed out by TEST PRINT consists of 16-step wedge, SMPTE pattern, and 1024-step gray scale. Measure the density of the 16-step wedge or SMPTE pattern and use it for the density control Opening/closing front cover COVER OPEN The touch position adjustment screen will appear Adjusting control panel PANEL ADJUSTThe PANEL ADJUST screen will appear The maintenance menu screen will re-appear3 Touch OK Clearing queued print data QUEUE CLEAR 4 Touch OK on the conﬁrm message The COLD START function re-starts the device COLD STARTmonth, touch MONTHLY Conﬁrming and setting ﬁlm count data1 Touch FILM DATA on the maintenance menu screen Conﬁrming ﬁlm count dataIf you wish to cancel the settings, touch CANCEL Follow the procedure below to set the ﬁlm count preferencesThe FILM DATA SETUP screen will appear The setting becomes valid, and the ﬁlm count data screen re- appearsSetting print preference Sets the bin in the sorter option into which the 12 Select the item to be printed as the stamp with STAMP SELECT 16 Sets the format of date to be printed on the ﬁlm 2 Touch LUT LIBRARY Setting user LUT4-3.How To Operate Maintenance Mode 1 Touch the user LUT name to be set on the LUT select screenCreating user LUT Conﬁrming the LUT curve 8 After the settings are complete, touch OK4-3.How To Operate Maintenance Mode 6 Touch EDIT on the LUT data screenSetting power saving mode 4-3.How To Operate Maintenance Mode 6 After the settings are complete, touch OKpage 5. Troubleshooting5-1. Error Display and Remedy pagePage 5-2.Resetting Errors 5-2. Resetting ErrorsWhen an error cannot be reset If ERROR RESET cannot function by clearing a queued error, follow the procedure below to re-start the device When SORTER COVER is displayed 5-3. Removing JamWhen TRAY OPEN is displayed When COVER OPEN is displayedJam in tray Film jam between decent transport section and exposure section Green lever Film jam between exposure section and elevator transport sectionFilm jam between HPRO section and cooling/discharge section Caution on High TemperaturesCaution on High Temperatures Film jam in sorter 1 Open the inlet guide, and remove jammed ﬁlms if there are any58 DRYPRO MODEL 752 Operation Manual Ver.0.11 Sorter left cover 3 Remove jammed ﬁlms if they remain4 Lift the handle of the sorter left cover to remove it 5 Open the ﬁlm transport guide, and remove jammed ﬁlms if they remainlower Guide pins6 Put the ﬁlm transport guide back, and remove the sorter left cover Film transport guide5-4. When Film Fails to be Loaded 5-4.When Film Fails to be LoadedRail 5 Open the light shield cover of the tray 14 Touch OK 15 Touch EXIT to end the maintenance mode 5-4.When Film Fails to be Loaded13 Touch the key of the tray in which you wish to re- load the ﬁlm 16 Touch FILM SET 17 When the tray pops out slightly, press in it until it locksInside of main unit 6. Service and Maintenance6-1. Periodical Maintenance and Inspection Outer cover of the main unitCaution on High Temperatures 6-2. Replacing FILTER6-3. Service and Maintenance Schedule Other service and maintenanceServicing by a user Conﬁrming maintenance and maintenance display the Regius 7. SpeciﬁcationsWhen connected to the Regius When connected to any other thanSorter Option Speciﬁcations Time zone and code No. table Appendix1.Handling and Storage of Unexposed Film 2.Handling and Storage of Developed FilmHANDLING AND STORAGE OF DRY FILM Blank page Blank page