Re-starting | Konica Minolta 752 specs

5-2.Resetting Errors

•Re-starting

If [ERROR RESET] cannot function by clearing a queued error, follow the procedure below to re-start the device.

When the device has started up with START TIMER function, clear START TIMER before re-starting the device.

(1)Press the start switch to turn the power of the device OFF.

(2)Press the start switch again to re-start the device.

IMPORTANT

•When the touch panel does not function for some reasons, re-start the device with the same procedure.

•When the error display persists even though turning the power OFF/ON, press the start switch to shut down the device, and contact a service person.

DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6 51

Image 63

Konica Minolta 752 operation manual Re-starting

Contents

Drypro model Blank DRY Laser Imager Drypro Model Sorter LiS-752 is optional device IntroductionOperation environment Imaging environment Symbol mark Descriptions of symbol mark Descriptions of Symbol Mark Descriptions on warning caution label Descriptions on Warning LabelPage Front Rear Be sure to ground the device well Safety Caution Plug the power cable completely Be careful not to trip over the power cable to damage itDo not operate the switches with wet hands When unplugging the power cable, do not pull it Precaution Disposal PrecautionPrecaution on Installation Location Name of Each Component Main BodyFront View Rear View Sorter LiS-752 option Structure How To Operate Control PanelDescription on screen Start-up Operation Power saving mode Shut-down Operation When Start Timer is not set to on Touch OK to perform Operation OFF proce- dure When Start Timer is set to on Shut-down Operation Film Loading Resin tray Seals at the edges of the package Push the tray to the back until it is locked Film Loading Function of Maintenance Mode Maintenance Mode Touch Maintenance Switching Maintenance ModeStart-up maintenance mode Shut-down maintenance mode Setting Start Timer Function How To Operate Maintenance Mode Setting Date/Time Time SET Touch Previous Print on the maintenance menu screen Re-printing Printed Page Previous PrintTouch on the upper part of the screen Touch the box on the right of Copy and input the print count Density Touch a LUT name you wish to apply for printing MIN Density Touch Store Calibrating Density Calibration Calibration Touch Calibration on the maintenance menu screen Automatic calibration Test Print Selected user LUT name will be highlighted Touch OK How to control density Opening/closing front cover Cover Open Touch Cover Open on the maintenance menu screen Touch Exit Adjusting control panel Panel Adjust How To Operate Maintenance Mode Clearing queued print data Queue Clear Touch OK on the conﬁrm message Cold Start Weekly ﬁlm count Monthly ﬁlm count Conﬁrming and setting ﬁlm count dataTouch Film Data on the maintenance menu screen Conﬁrming ﬁlm count data Touch Film Data Setup on the ﬁlm count data screen Setting ﬁlm count preference Touch Print Condition on the maintenance menu screen Setting print preference Print preference set screen 3/7 will appear Select the item to be printed as the stamp with Stamp Select Sets the format of date to be printed on the ﬁlm After the settings are complete, touch Exit Touch the name of the LUT to be applied Setting user LUTTouch the user LUT name to be set on the LUT select screen Touch LUT Library Touch User LUT on the maintenance menu screen Creating user LUTTouch Data on the lower part of the screen Conﬁrming the LUT curve Touch Edit on the LUT data screen Touch Power Save on the Maintenance Menu screen Setting power saving mode How To Operate Maintenance Mode Troubleshooting Error Display and RemedyError Code Description Remedy Error Display and Remedy Resetting Errors Touch Error Queue When an error cannot be reset Re-starting When Cover Open is displayed When Sorter Cover is displayedRemoving Jam Press in the tray until it locks Jam in tray Film outlet cover Green edge Film jam between Hpro section and cooling/discharge section Removing Jam Film jam in sorter Sorter left cover Cutouts When Film Fails to be Loaded Touch ON/OFF Line to switch into OFF Line Touch OK Touch Exit to end the maintenance mode When Film Fails to be Loaded Inside of main unit Service and MaintenancePeriodical Maintenance and Inspection Outer cover of the main unit Before replacing the FILTER, be sure to touch FIL Replacing Filter Service and Maintenance Schedule Other service and maintenanceServicing by a user Conﬁrming maintenance and maintenance display Drypro Model Speciﬁcations Sorter Option Speciﬁcations Time zone and code No. table Appendix Handling and Storage of Developed Film Handling and Storage of Unexposed Film Blank Blank