Manuals / Konica Minolta / Computer Equipment / Printer

Konica Minolta 752 operation manual Replacing FILTER, Caution on High Temperatures

Models: 752

1 87

Download 87 pages 20.91 Kb

Page 78

6-2. Replacing FILTER

6-2.Replacing FILTER

6-2. Replacing FILTER

[FILTER EXCHANGE] will be displayed on the control panel 6 months after the last replacement or after 10,000 prints.

Follow the procedure below to replace the FILTER.

(1)Touch [FILTER EXCHANGE] on the control panel.

The procedure for replacing the FILTER appears on the control panel.

CAUTION

Before replacing the FILTER, be sure to touch [FIL-

TER EXCHANGE].

(2) Open the FILTER cover upward.

(3)Hold the handle of the FILTER and lift it slightly.

Note that the FILTER is placed in the lower position.

(4)Pull out the FILTER.

Caution on High Temperatures

The temperature around the FILTER may reach

60 °C (140 °F) or over. So, be very careful of han- dling it.

(5) Insert a new FILTER to the back.

(6)Lower the FILTER into the speciﬁed position.

(7)Close the FILTER cover.

CAUTION

The device has the sensor to detect the pres- ence/absence of the FILTER. If the FILTER fails to be lowered into the speciﬁed place, the instal- lation of the FILTER is not detected.

66 DRYPRO MODEL 752 Operation Manual Ver.0.11 2002.6

Image 78

Konica Minolta 752 operation manual Replacing FILTER, Caution on High Temperatures

Contents

CODE NO 0463 UL, 0467 CE DRYPRO modelLASER IMAGER KONICACORPORATIONBlank page DRY LASER IMAGER DRYPRO MODEL Table of ContentsIntroduction Descriptions of Symbol Mark Symbol markDescriptions of symbol mark Descriptions on Warning Label Descriptions on warning caution labelWarning Label Warning Label Location 1 Front2 Rear Safety Caution Cautions on installationCautions on transporting, storing temporally, and servicing Cautions on use otherwise, dust may be accumulated, resulting in heating or a ﬁre Precaution Disposal PrecautionPrecaution on Installation Location 1-1. Main Body Control panel Start switch Upper tray Lower tray Front cover1. Name of Each Component Front ViewRear View Power connectorPower cable Air outlet1-2. Sorter LiS-752 option Bins Inlet guide Sorter left cover Front cover2. Structure 3. How To Operate 3-1. Control PanelDescription on screen Start switch 3-2. Start-up OperationBreaker Power saving mode Touch WAKE UP on the control panel3-3. Shut-down Operation When START TIMER is set to ON Press the start switch to re-start the equip- ment 3-4. Film Loading 3-4.Film LoadingFilm loading screen Barcode Empty packageSeals Retaining plate9 Push the tray to the back until it is locked Load the ﬁlm by referring to Steps 2 or later 4. Maintenance Mode 4-1. Function of Maintenance Mode4-2. Switching Maintenance Mode Start-up maintenance modeShut-down maintenance mode 4-3. How To Operate Maintenance Mode Setting START TIMER FunctionSetting Date/Time TIME SET Re-printing Printed Page PREVIOUS PRINT The print data on the speciﬁed page will be queued 8 Touch a LUT name you wish to apply for printing 9 Touch on the upper part of the screen11 Select NEGA/POSI by touching NEGA or POSI Calibrating Density CALIBRATION The DRYPRO has the automatic density calibration function that perform the density calibration automatically after a lapse of the speciﬁed time or speciﬁed number of printing. Instead of performing automatic calibration, you can make CALIBRA- TION appear on the screen to show you that the calibration needs performing depending on the settings at installation TEST PRINT 5 Touch on the upper part of the screen 9 Select NEGA/POSI by touching NEGA or POSI 14 Touch EXIT to end the maintenance mode4-3.How To Operate Maintenance Mode 10 Touch on the upper part of the screenEach frame of the SMPTE pattern for this device which is printed out by TEST PRINT consists of 16-step wedge, SMPTE pattern, and 1024-step gray scale. Measure the density of the 16-step wedge or SMPTE pattern and use it for the density control Opening/closing front cover COVER OPEN The maintenance menu screen will re-appear Adjusting control panel PANEL ADJUSTThe PANEL ADJUST screen will appear The touch position adjustment screen will appear3 Touch OK Clearing queued print data QUEUE CLEAR 4 Touch OK on the conﬁrm message COLD START The COLD START function re-starts the deviceConﬁrming ﬁlm count data Conﬁrming and setting ﬁlm count data1 Touch FILM DATA on the maintenance menu screen month, touch MONTHLYThe setting becomes valid, and the ﬁlm count data screen re- appears Follow the procedure below to set the ﬁlm count preferencesThe FILM DATA SETUP screen will appear If you wish to cancel the settings, touch CANCELSetting print preference Sets the bin in the sorter option into which the 12 Select the item to be printed as the stamp with STAMP SELECT 16 Sets the format of date to be printed on the ﬁlm 1 Touch the user LUT name to be set on the LUT select screen Setting user LUT4-3.How To Operate Maintenance Mode 2 Touch LUT LIBRARYCreating user LUT 6 Touch EDIT on the LUT data screen 8 After the settings are complete, touch OK4-3.How To Operate Maintenance Mode Conﬁrming the LUT curveSetting power saving mode 6 After the settings are complete, touch OK 4-3.How To Operate Maintenance Modepage 5. Troubleshooting5-1. Error Display and Remedy pagePage 5-2. Resetting Errors 5-2.Resetting ErrorsWhen an error cannot be reset If ERROR RESET cannot function by clearing a queued error, follow the procedure below to re-start the device When COVER OPEN is displayed 5-3. Removing JamWhen TRAY OPEN is displayed When SORTER COVER is displayedJam in tray Film jam between decent transport section and exposure section Film jam between exposure section and elevator transport section Green leverCaution on High Temperatures Film jam between HPRO section and cooling/discharge sectionCaution on High Temperatures Film jam in sorter 1 Open the inlet guide, and remove jammed ﬁlms if there are any58 DRYPRO MODEL 752 Operation Manual Ver.0.11 5 Open the ﬁlm transport guide, and remove jammed ﬁlms if they remain 3 Remove jammed ﬁlms if they remain4 Lift the handle of the sorter left cover to remove it Sorter left coverFilm transport guide Guide pins6 Put the ﬁlm transport guide back, and remove the sorter left cover lower5-4. When Film Fails to be Loaded 5-4.When Film Fails to be LoadedRail 5 Open the light shield cover of the tray 14 Touch OK 15 Touch EXIT to end the maintenance mode 5-4.When Film Fails to be Loaded13 Touch the key of the tray in which you wish to re- load the ﬁlm 17 When the tray pops out slightly, press in it until it locks 16 Touch FILM SETOuter cover of the main unit 6. Service and Maintenance6-1. Periodical Maintenance and Inspection Inside of main unit6-2. Replacing FILTER Caution on High Temperatures6-3. Service and Maintenance Schedule Other service and maintenanceServicing by a user Conﬁrming maintenance and maintenance display When connected to any other than 7. SpeciﬁcationsWhen connected to the Regius the RegiusSorter Option Speciﬁcations Appendix Time zone and code No. table1.Handling and Storage of Unexposed Film 2.Handling and Storage of Developed FilmHANDLING AND STORAGE OF DRY FILM Blank page Blank page