Connecting via the Ethernet | Kramer Electronics Revision 6 guide

Connecting via the ETHERNET

12Connecting via the ETHERNET

You can connect the device (for example, the SV-551)via the Ethernet using a crossover cable (see Section 12.1) for direct connection to the PC, or a straight through cable (see Section 12.2) for connection via a network hub or network router.

12.1Connecting the ETHERNET Port directly to a PC (Crossover Cable)

You can connect the Ethernet port of the RC device to the Ethernet port on your PC, via a crossover cable with RJ-45 connectors.

This type of connection is recommended for identification of the factory default

IP Address of the RC device (192.168.1.39) during the initial configuration

After connecting the Ethernet port, configure your PC as follows:

1.Right-click the My Network Places icon on your desktop.

2.Select Properties.

3.Right-click Local Area Connection Properties.

4.Select Properties.

The Local Area Connection Properties window appears.

5.Select the Internet Protocol (TCP/IP) and click the Properties Button (see Figure 182).

Figure 182: Local Area Connection Properties Window

6.Select Use the following IP Address, and fill in the details as shown in Figure 183.

7.Click OK.

Figure 183: Internet Protocol (TCP/IP) Properties Window

12.2 Connecting the ETHERNET Port via a Network Hub (Straight-Through Cable)

You can connect the Ethernet port of the RC device to the Ethernet port on a network hub or network router, via a straight-through cable with RJ-45 connectors.

87

Image 94

Kramer Electronics Revision 6 manual Connecting via the Ethernet, Local Area Connection Properties Window

Contents

Kramer K-Config Guide Revision Contents Figures Setting the LCD and Button Label Names Move the Stop Timer Action Set the New Command Table Name Tables Applicable Room Controllers IntroductionApplicable Room Controllers Available Commands for Room Control Ports Room Controller Commands Available Trigger Types Available Available Triggers for Room Controllers Actions, Labels and Button Number Limits How to Save a ProjectRoom Controller Devices Limitation To configure your Room Controller, follow these basic steps Quick Start Glossary Initial PlanningGlossary Installing the USB Driver Kramer K-Config Software InstallationInstalling the .NET Framework Revision 2.0 Software Defining the System Click OK Following window appears see Figure Installing Kramer K-Config SoftwareSelect or create a new working directory3 see Figure Importing xml Templates Peripheral Device DriversDownloading the Drivers Importing the Drivers Driver Manager Window Prior to Installing the Drivers Importing the Driver Files Defining the Control Room Loading the Drivers Adding the Master Device Auxiliary Device View Special Auxiliary Devices Device Operations Basic Virtual Device Front Panel Custom Virtual Device Appearance in K-Config Virtual Device appears in the Front Panel area see Figure Right click the label and buttons to name them see Figure DVD Control Virtual Device Front Panel RC-4 Remote Controller Tab Area Settings Defining the Port Manager Drivers Tree Window Selecting a Driver Writing a Port Description Defining the Ethernet Ports Select the Edid file to upload and click Open Edid file is uploaded Device Settings Tab Connect Dialog Box Device Settings Tab Features DST Summarizes date and time setting options Setting the Date and Time Web Settings Tab Web Settings Window Triggers Built-in Triggers Adding Actions to a Trigger Select the desired port for example, RS-232.DType Selecting the Command Replacing an Action All On Trigger with actions assigned Selecting the Action to be replaced from the Action List Selecting a New Action Adding a Custom Trigger Type the name of the custom trigger, and then click OK Set the Schedule Scheduling Window Monitor Event Trigger Add actions to the trigger see Section Add Timer Trigger Timer Trigger Flowchart Power on Example Timer Trigger in the Triggers List Set the Timeout Projector Power on Command in the Button Trigger Action List Selecting the Timer Start/Stop Action Step III Define the Monitor Event System Inactivity Example Set the timeout to 20 minutes1 Add the following actions2 see Section Add the Stop Timer trigger Add the Start Timer trigger GPI/O Trigger Add GPI/O Trigger Button Digital Input Select the condition for activating the trigger Add actions to the new trigger see Figure Select the trigger behavior GPI/O Defined as Digital Output Button Trigger Select the Behavior of the Digital Input Trigger Button Trigger Properties Window Select the Button Behavior Button Trigger Properties Window Toggle Toggle Number in the Action List Knob Turning Trigger Action Type Shows the port command actions1 Shows the available button ignore states Button Color Selection Switcher Command Action Type Shows the unlock PIN code Select LEDs to Light Definition of 4 States Setting the State Action List States Action Type Delay Action Type Write the Configuration Click Yes to write the configuration to the device Set K-NET IDs Click OK to connect Setting K-NET ID window appearsClick OK to set the ID number Driver Manager Window Driver Manager Window Features Driver Manager Creating a Driver Command New Serial Command Window Write the serial command1, as illustrated in Figure Writing a Serial Command Creating an IR Command New IR Command Window Creating Serial Range Commands Click OK Click the Table Details button Setting the Number of Command Rows Writing the Commands Logarithmic Row Selection Adding Actions to a Trigger via the Command Table Setting a Specific Volume Level Add the Command table to the list Adding the Commands Table to the List Selecting commands 0 to Selecting commands in the Port Command Area Defining Queries Feature Function Query Format Details Lamp Hour Query Response Formats Query Details Window Writing the Query Command Lamp Hours Projector Query Response Lamp Hours Shows the query format details Lamp Hour Query Format Details Power Query Response Formats Writing the Query Command Power Projector Query Response Power Query Format tab, set the query format, see Figure Expected Result Table Power File Menu Features Kramer K-Config MenusThis section describes the Kramer K-Configmenus File Menu Saving a Project Select Virtual Device to Save Export Device xml File Device Menu Features Device Menu Load Firmware Upgrade Window SV-551 Connect Window Help Menu Features Help Menu Connecting via the Ethernet Local Area Connection Properties Window