Liebert DS user manual Cgd

35"

(889mm)

Piping Schematics

Figure 74 Primary connection locations—upflow, air-cooled, 28-42kw (8-12 ton), semi-hermetic compressor models

NOTES:

1.Drawing not to scale.

2.Tolerance on all piping dimensions is ± 1/2" (13mm).

Field-routed alternatives for refrigerant gas and liquid line connection points. See submittal page DPN001120 for blower outlet and deck dimensional data.

6"

(152mm)

17-3/16" (437mm)

14-1/4"

3-7/8" (362mm)

(98mm) 15-7/8" (403mm)

Left Side Section View

		All dimensions from
	22-1/2"	rear corner of unit
	(572mm)	including panels
15-3/16"		Blower
		Outlet
(386mm)
4"	16-7/16"
(102mm)
	(418mm)
		86" (2184mm)
		Top View	Front of Unit

20-1/16" (509mm)

Factory Location
Front Section View	DPN001114
(Left Front Panel Not Shown)
	Rev. 02

		X	Y		Connection Size / Opening
Point	Description	inches (mm)	inches (mm)		inches (mm)
R1 3	Refrigerant Access (Top)	60-11/16 (1542)	1-7/8	(48)	22-1/2 x 15-3/16 (572 x 386)
R2 3	Refrigerant Access (Bottom)	63 (1600)	13-13/16 (351)		16-7/16 x 4 (418 x 102)
L1	Liquid Line System 1	79-3/16 (2011)	16-3/4 (425)		1/2 Cu Sweat
L2	Liquid Line System 2	76-1/2 (1943)	16-3/4 (425)		1/2 Cu Sweat
G1	Hot Gas Discharge 1	73-7/8 (1876)	16-3/4	(425)	5/8 Cu Sweat
G2	Hot Gas Discharge 2	70-1/8 (1780)	16-3/4	(425)	5/8 Cu Sweat
R3 3	Refrigerant Access (Side)	-	-		6 x 17-3/16 (152 x 437)
CGD*	Condensate Gravity Drain	-	-		3/4 FPT
CPD	Condensate Pump Discharge (Opt)	56-1/4 (1429)	11-1/8	(283)	1/2 Cu Sweat
HUM	Humidifier Supply Line	56-1/4 (1429)	9-1/8 (233)		1/4 Cu Sweat
ECS**	Econ-O-Coil Supply	56 (1423)	7-5/16 (186)		1-5/8 Cu Sweat
ECR**	Econ-O-Coil Return	56 (1423)	4-1/2 (114)		1-5/8 Cu Sweat
E1	Electrical Connection (High Voltage)	52-3/8 (1330)	30 (762)		2-1/2
E2	Electrical Connection (High Voltage)	46-7/8 (1191)	30 (762)		2-1/2
LV1	Electrical Connection (Low Voltage)	19-1/2 (495)	29-1/16 (738)		7/8
LV2	Electrical Connection (Low Voltage)	19-1/2 (495)	30-1/2 (775)		7/8
LV3	Electrical Connection (Low Voltage)	19-1/2 (495)	31-15/16 (811)		7/8

*Field-pitch condensate drain line a minimum of 1/8" (3.2 mm) per foot (305 mm). All units contain a factory installed condensate trap. Do not trap external to the unit. Drain line may contain boiling water. Select appropriate drain system materials. The drain line must comply with all local codes.

**Supplied on Dual-Cool systems only (4-pipe system)

99