Install the MDF | Lucent Technologies 555-230-128 guide

DEFINITY Enterprise Communications Server Release 6	Issue 3
Installation and Test for Compact Modular Cabinets 555-230-128	May 1998
1 Install and Cable the Cabinets
Install Main Distribution Frame and External Modem	Page 1-26

Install Main Distribution Frame and

External Modem

Install the MDF

! CAUTION:

The optional MDF is a special 110 cross-connect field and is smaller than standard 110 cross-connect hardware. Do not install standard 110 hardware inside the right panel.

NOTE:

The depth of any equipment installed inside the right panel must not exceed 2.5 inches (6.3 cm), otherwise the right cover panel cannot fit over the right panel.

The optional MDF represents the trunk/auxiliary field.

1.Mount the optional MDF to the right panel. See Figure 1-16. The MDF may be mounted at the top of the right panel in other cabinets, if desired. See Figure 1-17.

Install the External Modem

The U.S. Robotics Model 839 external modem is the recommended external modem. Release 6 CMC systems operate with this modem set to the factory default settings.

NOTE:

You may use a locally obtained, type-approved external modem (33.6 bps and V.34 protocol). Contact your Lucent Technologies representative for more information.

1.Use installer-provided hardware to mount the modem. See Figure 1-16.

2.Route the MODEM cable (P2) from the Processor Interface Cable through the cable trough and to the modem.

3.Connect the cable to the modem. Refer to ‘Processor‘ Interface Cable Pinout’’ on page 2-11 for the pinout of the modem cable.

4.Plug the modem power cord into an electrical outlet and turn on the modem.

5.Modem setup and administration is performed in ‘External‘ Modem Option Settings’’ on page 1-98.

Image 34

Lucent Technologies 555-230-128 manual Install Main Distribution Frame External Modem, Install the MDF

Contents

Definity Trademarks Contents Installation Completion and Cable Pinouts References Definity Enterprise Communications Server Release About This Book Conventions Used in This Book Definity Enterprise Communications Server Release Check Customer’s Order Correcting Shipping ErrorsUnpack and Inspect Figure Notes Lists the comcodes for equipment used with the CMC Comcodes for CMCComcodes for Release 6.1 and Later CMC Description Comcodes for CMC On next Install the System Cabinets Set the Carrier Address ID All Cabinets Typical Floor Mount Installation Floor-Mount the Cabinet Wall-Mount the Cabinets Install Plywood Backing onto WallSingle-Cabinet Installation Or 3 Vertically Mounted Cabinets Install Cabinet a Wall-Mount Left Panel Used as Mounting Template #12 x 1-inch shoulder screws #12 x 1-inch safety screw Typical Wall-Mount Installation Install 2 or 3 Vertically Mounted Cabinets Securely tighten the shoulder screws and safety screws Install 2 Cabinets Vertically and 1 Cabinet Horizontally Typical 3-Cabinet Installation Install Left and Right Panels Wall-Mount Left panel Right panel AC Power and Ground Check AC Power Approved Grounds Uninterruptible Power Supply Approved Floor Grounds Connect Cabinet Grounds and Other Grounds CMC Cabinet Power SwitchLatch Issue Install the Ground Block #12 x 1-inch shoulder screws Single-point ground block 11. Typical Cabinet Grounding Install Coupled Bonding Conductor Connect and Route Cabinet AC Power Cords 12. Routing AC Power Cords to a Power Distribution Unit Cable the System 13. System Cable Connections 14. TDM/LAN Bus Cables and Terminators Vertically and Horizontally Mounted System 15. System Cable Connections Install the MDF Install Main Distribution Frame External ModemInstall the External Modem Cable the MDF and Modem Bottom-mounted MDF 16. Typical MDF and Modem Cable Routing Bottom-mount Top-Mounted MDF 17. Typical Top-Mount MDF Cable Routing Cross-Connect the Cabinets to the MDF Install Equipment Room Hardware650A AC Power Unit Yes 982LS Current Limiter Allowable Circuit Packs for CMC On next Multimedia Interface TN788B Multimedia Voice Conditioner On next Circuit Pack Installation Circuit Pack Slot Loading Line circuit pack slots Trunk circuit pack slots 18. Control Carrier Slot Layout Circuit Pack Installation Order Loading Function Apparatus Code Load From Cross-connect the port circuit packs to the MDF. See Figure 19. Example MDF Connections Install Sneak Fuse Panels Sneak current protector PEC Pair male connector Definity Enterprise Communications Server Release Is a pinout of the cable wiring and associated fuse numbers Sneak Fuse Connector Pinout Pair/Fuse Numbers Label the Main Distribution Frame Floor and building identification Install and Set Up the Management Terminal Set Up the Management Terminal 22. Rear Panels on Management Terminals Remotely Connect Terminal 23. Typical Connections to Remote Devices Ringing option switch Set Ringing Option Multi-Cabinet Installations Activate and Administer the SystemPower Up System Single Cabinet Installations System Administration Check System Status Log into the SystemChange Customer Options Set Country Options Screen 1-1. Typical System Parameters Country-Options Screen Country Codes USA Change Craft Password Screen 1-2. Typical Change Password Screen Screen 1-3. Typical Date and Time Screen Set Date and TimeEnglish Day of the Week Names Day Number Day Name English Month Names Month Number Circuit Pack Administration Set System Maintenance Parameters Save Translations Administer the Attendant ConsoleAdd Translations Install and Wire Telephones and Other Equipment Telephone Connection Examples 25 C1 to TN754B Wiring Connect Adjunct Power 26 B2 Adapter Connecting to a Modular Plug Analog Station or 2-Wire Digital Station Example Type analog station Wire analog line circuit pack Analog Tie Trunk Example External trunk or adapter Tie trunk circuit pack 29. Digital Tie Trunk Wiring Digital Tie Trunk Example Collocated DS1 Tie Trunks Pinout of C6F Cable Wire Color Lead Designation NumberDS1 Tie Trunk Example White/Green High Side White/Brown LO High Side White/Slate DS1 Tie Trunks Using T1 Channel Service Unit 30. Typical Connections to Channel Service Unit Pair and 4-Pair Modularity 31 -Pair and 4-Pair Modularity Adjunct Power Connections 32 shows typical connection locations for adjunct power Auxiliary Power Local and Phantom PowerAttendant Console Cabling Distances Dual Wiring of 2-Wire and 4-Wire Endpoints Install Attendant Console OptionalHard-Wire Bridging Install 26B1 Selector Console Optional Alarm Output Connect External Alarms Auxiliary ConnectionsAlarm Input 10. Alarm Inputs at AUX Connector Color Telephone Pin Designations Emergency Transfer and Auxiliary Power13. Port Circuit Pack and Telephone Pin Designations Hardware Setup CAMA/E911 InstallationConfiguration Administration Setup Screen 1-5. Administrable Timers form Trunk Group Administrable Timers Screen 1-7. Feature Access Code FAC form Screen 1-6. Group Member Assignments form At the prompt, enter change ars analysis 9 and press Enter Feature Access Code FAC screen page 1 appearsScreen 1-8. ARS Digit Analysis Table Screen 1-9. Route Pattern form CA-TSC ITC Screen 1-10. Route Pattern form Screen 1-11. Cama Numbering Format form Screen 1-12. Class of Restriction form FRL APLT? Install the BRI Terminating Resistor Terminating Resistor Adapter Wide plug Wide jack Closet Mounted 110RA1-12 34. Terminating Resistor Block 110RA1-12 35. Typical Installation of Terminating Resistor Block Install Multi-point Adapters BR851-B Adapter T-Adapter 367A Adapter Wiring Diagram of 367A AdapterJack 367A adapter Basic Multi-point Installation Distances 38. Basic Multi-point with One Work Location Install Off-Premises or Out-of-Building Stations Install Off-Premises Station WiringAnalog Off-Premises Stations 39. Connections for 1 to 8 Out-of-Building Analog Telephones 40. Connections to 24 Out-of-Building Telephones 14. Analog Line Circuit Protectors Circuit ProtectorsPrimary Sneak Current With heat coil Protectors Digital Out-of-Building Telephones Install Emergency Transfer Unit Associated Telephones Install the Emergency Transfer Panel 41 a Emergency Transfer Panel Test Switch Trunk/Test SwitchesSwitch Circuit Number Not Used TTC1 RLC4 42. Connections for Telephone Used for Emergency Transfer R758582b MMR Telephone Installation 18. Pinout of Network Jack Pin Number Signal Connect Modem to Telephone Network External Modem Option Settings 19. U.S. Robotics Model 839 External Modem Switch Settings 20. Release 6 CMC Modem Fields Description Line tone or pulse to the modem Character blank field default and is not case-sensitiveAnswers an incoming call. This field should be set to S0=10 67% break for the United Kingdom and Hong Kong. This is a Perform System Administration Resolve Alarms External Modem Installed Place a Test Call Setting the Neon Voltage Set Neon Voltage Ring Ping Power Supply LED Indications Installation CompletionLED and Alarm Conditions LED Status Alarm State Fan Alarm Type I Standard unprotected TN760D Tie Trunk Option SettingsSignaling Formats for TN760D Mode Type Type I Compatible unprotected Smplx TN464E/F Option Settings Option Switch Settings on TN464E/F TN464E/F Option Settings Connector and Cable Diagrams Pinout Charts Lead and Color Designations Cross-Connect Amphenol Pin Color Backplane Pin Processor Interface Cable Pinout Processor P1 Amphenol Signal Name Connector AUX J1Processor Interface Cable Pinout Modem Port Circuit Pack Lead Designations All other pins are empty LOOP2 SL-W LOOP1 006 002005 007 On next 213 314 11. TN793 Analog Line Circuit Pack Pinout214 12. Circuit Pack and Auxiliary Equipment Classifications 128 13. Circuit Pack and Auxiliary Equipment Leads Pinout Charts TXR6 Following wire colors apply in the above chart Digital Trunk References Related Documents Where to Call for Technical Support How to Order DocumentationHow to Comment on This Book Security Issues Trademarks Callmaster CallVisor National ISDN-1 National ISDN-2 ISO-9000 Standards ComplianceFCC Part 15 and Part EN55022 EN50081 EN50082 Electromagnetic Compatibility Standards European Union Standards Federal Communications Commission Statement Part 68 Statement Means of Connection SOC/REN Index Diagrams, 2-9, 2-15, 18 to 20 changing BRI AC, 1-17 grounding Inads Mu-Law companding Multipoint Multipoint adapters IN-6 IN-7 IN-8