Check Customer’s Order | Lucent Technologies 555-230-128 guide

DEFINITY Enterprise Communications Server Release 6	Issue 3
Installation and Test for Compact Modular Cabinets 555-230-128	May 1998
1 Install and Cable the Cabinets
Check Customer’s Order	Page 1-1

1

Install and Cable the Cabinets	1

Check Customer’s Order

Check the customer’s order and the shipping packing lists to confirm that all equipment is present. If any equipment is missing, report this to your Lucent Technologies representative. Check the system adjuncts for damage and report all damage according to local shipping instructions.

Correcting Shipping Errors

1.Red-tag all defective equipment and over-shipped equipment and return according to the nearest Material Stocking Location (MSL) instructions. For international customers, contact your order service agent.

2.Direct all short-shipped reports to the nearest MSL. Contact the appropriate location for specific instructions. For Streamlined Implementation in the United States, call 1-800-772-5409.

Unpack and Inspect

READ THIS FIRST !

! CAUTION:

A fully loaded system weighs 58 lbs (26.3 kg). Use lifting precautions. If the doors, power unit, and circuit packs are removed, the unit weighs only 29 lbs (13.1 kg).

1.Verify the equipment received. See Figure 1-1. Actual equipment may vary in appearance and may ship in separate packages.

Image 9

Lucent Technologies 555-230-128 manual Check Customer’s Order, Correcting Shipping Errors, Unpack and Inspect

Contents

Definity Trademarks Contents Installation Completion and Cable Pinouts References Definity Enterprise Communications Server Release Conventions Used in This Book About This Book Definity Enterprise Communications Server Release Correcting Shipping Errors Check Customer’s OrderUnpack and Inspect Figure Notes Comcodes for CMC Lists the comcodes for equipment used with the CMCComcodes for Release 6.1 and Later CMC Description Comcodes for CMC On next Set the Carrier Address ID All Cabinets Install the System Cabinets Floor-Mount the Cabinet Typical Floor Mount Installation Single-Cabinet Installation Install Plywood Backing onto WallWall-Mount the Cabinets Or 3 Vertically Mounted Cabinets Left Panel Used as Mounting Template Install Cabinet a Wall-Mount Typical Wall-Mount Installation #12 x 1-inch shoulder screws #12 x 1-inch safety screw Securely tighten the shoulder screws and safety screws Install 2 or 3 Vertically Mounted Cabinets Typical 3-Cabinet Installation Install 2 Cabinets Vertically and 1 Cabinet Horizontally Left panel Right panel Install Left and Right Panels Wall-Mount Check AC Power AC Power and Ground Approved Grounds Approved Floor Grounds Uninterruptible Power Supply CMC Cabinet Power Switch Connect Cabinet Grounds and Other GroundsLatch Issue #12 x 1-inch shoulder screws Single-point ground block Install the Ground Block 11. Typical Cabinet Grounding Connect and Route Cabinet AC Power Cords Install Coupled Bonding Conductor 12. Routing AC Power Cords to a Power Distribution Unit 13. System Cable Connections Cable the System 14. TDM/LAN Bus Cables and Terminators 15. System Cable Connections Vertically and Horizontally Mounted System Install Main Distribution Frame External Modem Install the MDFInstall the External Modem 16. Typical MDF and Modem Cable Routing Bottom-mount Cable the MDF and Modem Bottom-mounted MDF 17. Typical Top-Mount MDF Cable Routing Top-Mounted MDF 650A AC Power Unit Yes 982LS Current Limiter Install Equipment Room HardwareCross-Connect the Cabinets to the MDF Allowable Circuit Packs for CMC On next Multimedia Interface TN788B Multimedia Voice Conditioner On next Circuit Pack Installation Circuit Pack Slot Loading 18. Control Carrier Slot Layout Line circuit pack slots Trunk circuit pack slots Function Apparatus Code Load From Circuit Pack Installation Order Loading 19. Example MDF Connections Cross-connect the port circuit packs to the MDF. See Figure Sneak current protector PEC Pair male connector Install Sneak Fuse Panels Definity Enterprise Communications Server Release Sneak Fuse Connector Pinout Pair/Fuse Numbers Is a pinout of the cable wiring and associated fuse numbers Floor and building identification Label the Main Distribution Frame Install and Set Up the Management Terminal 22. Rear Panels on Management Terminals Set Up the Management Terminal 23. Typical Connections to Remote Devices Remotely Connect Terminal Set Ringing Option Ringing option switch Power Up System Single Cabinet Installations Activate and Administer the SystemMulti-Cabinet Installations System Administration Log into the System Check System StatusChange Customer Options Screen 1-1. Typical System Parameters Country-Options Screen Set Country Options USA Country Codes Screen 1-2. Typical Change Password Screen Change Craft Password Set Date and Time Screen 1-3. Typical Date and Time ScreenEnglish Day of the Week Names Day Number Day Name English Month Names Month Number Set System Maintenance Parameters Circuit Pack Administration Administer the Attendant Console Save TranslationsAdd Translations Telephone Connection Examples Install and Wire Telephones and Other Equipment 25 C1 to TN754B Wiring 26 B2 Adapter Connecting to a Modular Plug Connect Adjunct Power Type analog station Wire analog line circuit pack Analog Station or 2-Wire Digital Station Example External trunk or adapter Tie trunk circuit pack Analog Tie Trunk Example Digital Tie Trunk Example 29. Digital Tie Trunk Wiring DS1 Tie Trunk Example Pinout of C6F Cable Wire Color Lead Designation NumberCollocated DS1 Tie Trunks White/Green High Side White/Brown LO High Side White/Slate 30. Typical Connections to Channel Service Unit DS1 Tie Trunks Using T1 Channel Service Unit 31 -Pair and 4-Pair Modularity Pair and 4-Pair Modularity 32 shows typical connection locations for adjunct power Adjunct Power Connections Local and Phantom Power Auxiliary PowerAttendant Console Cabling Distances Hard-Wire Bridging Install Attendant Console OptionalDual Wiring of 2-Wire and 4-Wire Endpoints Install 26B1 Selector Console Optional Alarm Input Connect External Alarms Auxiliary ConnectionsAlarm Output 10. Alarm Inputs at AUX Connector Color Emergency Transfer and Auxiliary Power Telephone Pin Designations13. Port Circuit Pack and Telephone Pin Designations Configuration CAMA/E911 InstallationHardware Setup Administration Setup Trunk Group Administrable Timers Screen 1-5. Administrable Timers form Screen 1-6. Group Member Assignments form Screen 1-7. Feature Access Code FAC form Feature Access Code FAC screen page 1 appears At the prompt, enter change ars analysis 9 and press EnterScreen 1-8. ARS Digit Analysis Table CA-TSC ITC Screen 1-9. Route Pattern form Screen 1-10. Route Pattern form Screen 1-11. Cama Numbering Format form FRL APLT? Screen 1-12. Class of Restriction form Install the BRI Terminating Resistor Wide plug Wide jack Terminating Resistor Adapter 34. Terminating Resistor Block 110RA1-12 Closet Mounted 110RA1-12 35. Typical Installation of Terminating Resistor Block BR851-B Adapter T-Adapter Install Multi-point Adapters Wiring Diagram of 367A Adapter 367A AdapterJack 367A adapter 38. Basic Multi-point with One Work Location Basic Multi-point Installation Distances Install Off-Premises Station Wiring Install Off-Premises or Out-of-Building StationsAnalog Off-Premises Stations 39. Connections for 1 to 8 Out-of-Building Analog Telephones 40. Connections to 24 Out-of-Building Telephones Circuit Protectors 14. Analog Line Circuit ProtectorsPrimary Sneak Current With heat coil Protectors Digital Out-of-Building Telephones Install the Emergency Transfer Panel Install Emergency Transfer Unit Associated Telephones 41 a Emergency Transfer Panel Switch Circuit Number Trunk/Test SwitchesTest Switch Not Used TTC1 RLC4 42. Connections for Telephone Used for Emergency Transfer R758582b MMR Telephone Installation Connect Modem to Telephone Network 18. Pinout of Network Jack Pin Number Signal 19. U.S. Robotics Model 839 External Modem Switch Settings External Modem Option Settings 20. Release 6 CMC Modem Fields Description Answers an incoming call. This field should be set to S0=10 Character blank field default and is not case-sensitiveLine tone or pulse to the modem 67% break for the United Kingdom and Hong Kong. This is a Resolve Alarms Perform System Administration Place a Test Call External Modem Installed Set Neon Voltage Ring Ping Setting the Neon Voltage Installation Completion Power Supply LED IndicationsLED and Alarm Conditions LED Status Alarm State Fan Alarm Signaling Formats for TN760D Mode Type TN760D Tie Trunk Option SettingsType I Standard unprotected Type I Compatible unprotected Smplx Option Switch Settings on TN464E/F TN464E/F Option Settings TN464E/F Option Settings Connector and Cable Diagrams Pinout Charts Cross-Connect Amphenol Pin Color Backplane Pin Lead and Color Designations Processor Interface Cable Pinout Signal Name Connector AUX J1Processor Interface Cable Pinout Processor P1 Amphenol Modem Port Circuit Pack Lead Designations LOOP2 SL-W LOOP1 All other pins are empty 005 002006 007 On next 11. TN793 Analog Line Circuit Pack Pinout 213 314214 128 12. Circuit Pack and Auxiliary Equipment Classifications 13. Circuit Pack and Auxiliary Equipment Leads Pinout Charts TXR6 Digital Trunk Following wire colors apply in the above chart Related Documents References How to Comment on This Book How to Order DocumentationWhere to Call for Technical Support Security Issues Callmaster CallVisor Trademarks Standards Compliance National ISDN-1 National ISDN-2 ISO-9000FCC Part 15 and Part EN55022 EN50081 EN50082 Electromagnetic Compatibility Standards European Union Standards Part 68 Statement Federal Communications Commission Statement SOC/REN Means of Connection Index BRI Diagrams, 2-9, 2-15, 18 to 20 changing AC, 1-17 grounding Inads Mu-Law companding Multipoint Multipoint adapters IN-6 IN-7 IN-8