Napco Security Technologies GEM-P3200 GEM-RP1CAE2/GEM-K1CAKEYPAD EASY, Program Menu, Z N #

WI818G 10/05 Page 13

Z N #	X M I T # + C S P			RF Transmitter Points (Press Rto set cursor.)
				For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)
Z n 0 1 - 0 0 0 0 0 0 : 0 - 0
				• The zone number (01–48) to which the transmitter will be mapped.
Zone #	Xmitter	Check	Point
Mapped to	ID	Sum	#	• The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,

• The point number (1–2);enter “9” for unsupervised (all points).

• Press Uto save and NEXT/YES button to proceed when all transmitters have been entered.

NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A = G0; B = G1; C = G2; D = G3; E = G4and “F” = G5.

Quick Method (Enroll Method).			If a receiver is already installed in the panel, transmitter wireless points can be programmed automatically
			(“enrolled”) using the following procedure. NOTE: The transmitter point will be enrolled only if the signal
	Z N #	X M I T # + C S P	strength is 3 or greater.
	Z n 0 1 - 0 0 0 0 0 0 : 0 - 0		1.	Enter the zone number to which the transmitter point will be mapped.
			2.	Press Bto enter the Enroll Mode. The red and green LEDs on the keypad will
				flash and the window will display as shown at left.
	Z N #	X M I T # + C S P	3.	Open the loop of the point that is to be programmed (GEM-TRANS2 only).
			4.	Install the transmitter battery. The keypad will beep to indicate that the point has been
	Z N 0 1 - E N R O L L : A - -
				successfully enrolled. Multi-point transmitters can be mapped to successive zones
				simultaneously.
Example. A 2-point transmitter has the RF ID number 287613:1. Map point					to Zone 6).
1 to Zone 6 and point 2 to Zone 9.					5. Enter Zone “09”.
1. Enter the Enroll mode as described above.					6. Close point-1 loop and open point-2 loop.
2. Enter Zone “06”.					7. Remove the transmitter battery, then re-install it. The keypad will beep
3. Open point-1 loop.					once to indicate that one point has been programmed. (Transmitter
4. Install the battery. The keypad will beep once to indicate that one point					287613:1, point 2 is mapped to Zone 9).
	has been programmed. (Transmitter 287613:1, point 1 will be mapped

KEYFOB ZONE ASSIGNMENT: Keyfobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm sys- tem, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the keyfob, the location where the person holding the keyfob is stationed, or the special purpose of the keyfob button being depressed. See the next page on Keyfob Transmitters as Zone Input Devices .

GEM-RP1CAE2/GEM-K1CA KEYPAD EASY

K F A		X M I T # + C S O P
0 1 - 0		0 0 0 0 0 0 : 0 0 0
KF	Area Xmitter		Check	Aux
#		ID	Sum	1&2

Keyfob Transmitters as Arm/Disarm & Control Devices (Press Rto set cursor).

Keyfobs can be programmed as “Arm/Disarm” devices using their On/Off buttons (refer to WI752). For each Keyfob Transmitter, enter:

•The Keyfob Transmitter number (01–08).

•The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).

•The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,

•The Aux 1 Option (see keyfob aux 1 & aux 2 options).

•The Aux 2 Option (see keyfob aux 1 & aux 2 options).

•NOTE: Keyfobs 1-8 report openings and closings as Users 25-32.

•Press Uto save and NEXT/YES button to proceed when all keyfobs have been entered.

PROGRAM MENU

NOTE: When programming the ID Code number, “0” through ”9” = 0through 9; A = G0; B = G1; C = G2; D = G3; E = G4and “F” = G5.

LNAPCO Security Systems XGEM-P3200 Programming Instructions