Napco Security Technologies GEM-P3200 quick start Format Options, CS Receiver 1 Options

WI818G 10/05					Page 21
CS RECEIVER FORMAT OPTIONS (ADDRESS 0520, 0521, 0525, 0526, 0550, 0551, 0575 & 0576)
CS Receiver 1	ADDRESS 0525	CS Receiver 2	ADDRESS 0550	CS Receiver 3	ADDRESS 0575
Format		Format		Format

Default for CS Receiver 1 Format depends on Easy Menu Question “RCVR FORMAT”. [Default = •(blank) E] for CS Receivers 1, 2 and 3 Formats.

DATA ENTRIES		CS RECEIVER FORMATS
LEFT	RIGHT
blank (•)	blank (•)	Ademco Slow, Silent Knight Slow
blank (•)	1	Sescoa, Vertex, DCI, Franklin Fast
blank (•)	2	Radionics Fast
blank (•)	3	Silent Knight Fast
blank (•)	4	Radionics, DCI, Franklin Slow
blank (•)	5	Universal High Speed
blank (•)	8	Radionics BFSK
blank (•)	9	FBI 4/3/1
blank (•)	0	Radionics Modem 2
blank (•)	B	SIA
blank (•)	C	Ademco Point ID
blank (•)	D	Ademco Express
blank (•)	E	Pager
blank (•)	F	Disabled
1	blank (•)	Radionics Modem IIe

CS RECEIVER FORMATS: Up to 3 CS Formats may be programmed.

1.Select the desired CS Receiver Format from the table shown.

2.Enter in the corresponding digit address locations for each CS Receiver.

NOTE: Dark shaded data value box shows option not available.

Leading Digits	ADDRESS 0520	Leading Digits	ADDRESS 0521
for Pager		for Pager
Format		Format
(1st Digit)		(2nd Digit)
[Default = blank (•) blank (•)]		[Default = blank (•) blank (•)]

CS

LEADING DIGITS FOR PAGER FORMAT: In Pager Format reporting, the message typically begins with “00”. However, for some pager services, this will cause the Pager's Voice Mail feature to activate. This option allows you to program these digits to any number desired. Typical Pager report is “003 022 1234”, where 3 is the Event, 22 is the zone, and 1234 is the Subscriber ID number. For example, if the Leading Digits are programmed as “98”, the Pager report will now appear as “983 022 1234”.

1. Enter in 1st and 2nd Leading Digits in right digit only (left digit is not used) as shown.

RECEIVER

2. Valid entries are: 0-9. Press Uor Dto save

0526		CS Receiver 1 Options
Default				Option
OFF			1	1400Hz Handshake/Kissoff *
OFF			2	2300Hz Handshake/Kissoff *
OFF			3	Enable Zone Number on Pulse Alarm
OFF			4	Single Digit Only
OFF			5	Sum Check
OFF			6	3/1 with Extended Restores
OFF			7	Report to TCP/IP Receiver or AES (Telco 1)**
OFF			8	RESERVED
0576	CS Receiver 3 Options
Default				Option
OFF			1	1400Hz Handshake/Kissoff *
OFF			2	2300Hz Handshake/Kissoff *
OFF			3	Enable Zone Number on Pulse Alarm
OFF			4	Single Digit Only
OFF			5	Sum Check
OFF			6	3/1 with Extended Restores
OFF			7	Report to TCP/IP Receiver or AES (Telco 3)**
OFF			8	RESERVED

0551	CS Receiver 2 Options
Default			Option
OFF		1	1400Hz Handshake/Kissoff *
OFF		2	2300Hz Handshake/Kissoff *
OFF		3	Enable Zone Number on Pulse Alarm
OFF		4	Single Digit Only
OFF		5	Sum Check
OFF		6	3/1 with Extended Restores
OFF		7	Report to TCP/IP Receiver or AES (Telco 2)**
OFF		8	RESERVED

Default for CS Receiver 1 Format depends on Easy Menu Question “RCVR FORMAT”. [Default = •(blank) E] for CS Receivers 2 and 3 Formats.

CS RECEIVER FORMATS: Up to 3 CS Formats may be pro- grammed.

1.Select the desired CS Receiver Format from the table shown.

2.Enter the corresponding digit in the address location for each CS

Receiver. NOTE: Dark shaded data value box shows option not available. Press [Enter] of [ON/OFF] to save.

NOTES:

*If both are selected, 1400Hz has priority over 2300Hz.

**For NAPCO NetLink™ installations only: For each telephone num- ber desired, enable to allow the panel to report alarms via the NL-MOD accessory. See WI1242 for more information.

FORMAT OPTIONS

LNAPCO Security Systems XGEM-P3200 Programming Instructions