Norway | Oki 425D instruction

6.2.1.5 Norway

10xH and 1xH are Control Code areas.

2If a code received is other than a control code in 0xH and 1xH, it is ignored.

3The above table assumes international character set is set to “American.”

4The blank space (20H, 7FH, FFH) indicates a space code.

106 OKIPOS 425D

Image 106

Oki 425D manual Norway

Contents

Okipos 425D Mail Address Mailing AddressWeb Site Contents Troubleshooting and Repair Specifications Command Description Using the Unitool Printer Driver Where to install your printer Select a Location Unpacking Getting Started Installing the Printer Getting to Know the Okipos 425D Remove the Shipping Restraints Setting the Interface Board Assembly Setting the DIP Switches RS-232C Installing the Interface Board Assembly Connecting the Customer Display Connecting the ComputerConnecting the Cash Drawer Connecting the Power Installing the Ribbon Cartridge Unpack the ribbon cartridge Developer’s Guide English Installing the Paper Paper Specifications Maximum thickness 0.3 mm 0.012 inches Adjusting the Roll Paper Guide Receipt Roll paper Loading the Roll Paper Receipt Cut the roll paper Close the printer cover Adjusting the Roll Paper Guide Journal Loading the Roll Paper Journal Okipos 425D Adjusting the Roll Paper Near End Sensing Position Cut-Sheet Paper Slip Loading the Cut-Sheet Paper Slip Cut-Sheet Paper Validation/Stub Loading the Cut-Sheet Paper Validation/Stub How to remove the Piece Developer’s Guide English Sprocket Paper Tractor Loading the Sprocket Paper Tractor Developer’s Guide English Okipos 425D Developer’s Guide English Operation Panel Functions Operation Panel Switching Functions SW2 FF/LOD,PAK SW3 CUT SW1 LED OFF PowerLED Function LED Local Functions Types Starting SW2 SW3 SW1 SW4 OEM Standard Model Menu Function ReceiptOverview OKI Standard Model HSD Start How to OperateOperation Hex Dump Function Receipt How to PrintPrint Format Using the Micr Reader How to use the Micr Reader Micr Read Test Receipt When Read is NG When Read is OKReturn code Status Rewinder Winding Evaluation Continuous Print Test Journal Using the Auto Cutter How to Use Maintenance Replacing the Ribbon Cartridge Important! Do not remove the ribbon shield 1 from the ribbon Developer’s Guide English Replacing the Roll Paper Roll Paper Receipt Roll Paper Journal Okipos 425D Clearing Paper Jams Print head may be very hot. Exercise caution Auto Cutter Developer’s Guide English Service Cut-Sheet Paper Sprocket Paper Troubleshooting and Repair Alarm Indication for a Failure Details of Alarm Indications LED Indication LED LED 1 Error LED 2 StatusBlink Introduction CharacteristicsScope of Application Options Configuration Environmental Conditions General SpecificationsPower Requirements Agency Approvals GND Communication Interface SpecificationsParallel Interface OKI/OEM Standard Type Dkstatus 2 RS-232C Interface OKI Standard Type RTS DSR DTR Init CASHDV1 CASHST-N Cash Drawer connector OKI Standard TypeCASHDV2 DTR DSR Printhead Physical CharacteristicsPrinter Selectable Character Pitches Logical CharacteristicsPrint Direction Maximum Number of Characters per Line Line Feed Pitches Printer PerformanceFont Size/Cell Size Print Speed Cut-Sheet Paper Counterfoil/Stub Media SpecificationsCut-Sheet Paper Slip/Validation Roll Paper Receipt/Journal Cut-Sheet Paper Slip/Validation Appendix Media SpecificationsPaper Size and Printing Area Okipos 425D Developer’s Guide English Paper Quality Paper Weight and Maximum Duplicating QuantityFixing Method of Multi-part Paper Joint Binding Holes Perforated Lines Provisions on Fold, Bend and Curl on Cut-sheet Paper Roll paper Receipt/Journal Paper Weight Sprocket Paper Tractor Developer’s Guide English Paper Quality D E Okipos 425D Rising in Horizontal Perforated Line Position Deviation of Sprocket Holes Binding Holes Corner Cut Wrinkle, Pleat and Swell Micr only with Micr Type Paper Size and Scanning Area Paper Positioning Restrictions Paper Feed SpecificationsPaper feed methods/Paths Paper Tear-off Micr Specifications Only with Micr type Cutting Specifications Auto Cutter SpecificationsRibbon Specifications Reliability Function Code Control Code ListHEX DEC Code DC2 Can ESC ESC SI ESC DLE D ESC SequenceHEX 1B OD ESC ESC @ HEX GS sequenceUS Sequence HEX DEC Code DC2 Can DLE ESC DLE Sequence ESC Data FS Sequence GS ENQ Code table OEM Standard Type Character Set1.1 USA Canada-French Multilingual Portugal Norway Brascii Abicomp Multilingual ISO 8859/15 International character set table Code table OKI Standard Type 2.1 USA Canada-French Multilingual Portugal Norway Brascii Abicomp Multilingual ISO 8859/15 International character set table Using the Unitool Printer Driver Setting Slip Paper in the Paper Tray Using Registered Paper Icons Okipos 425D Developer’s Guide English Using Custom Size Using Paper Size that is less than 187.96 mm 7.4 in Width Image of actual printing area Example Developer’s Guide English Okipos 425D Developer’s Guide English Symbol Designation Standard Value About the Validation Printing Area Data in application Print result Example Setting Tractor Paper in the Tractor Unit Orientation Okipos 425D Developer’s Guide English