OKI Standard Model, Hsd | Oki 425D specs

2.3.2 OKI — Standard Model

No.

Item

1Auto Cutter Unit

2MICR Unit

3Print Registration

4Top Adjust

5Cut Adjust

6Auto LF

(Auto line feed)

7Receive Buffer Size

8Print Mode

9Off-line Busy Control

10Cover Open Alarm

11Width of Roll Paper

12Zero Character

13Page Length

14Paper End Signal

O = default value

Function

Selects Auto Cutter Unit Installed/Not Installed

Selects MICR Unit Installed/Not Installed

Adjusts the print position if it shifts in Forward printing and Reverse printing

Adjusts Top Of Form position when Slip/Sprocket are used.

Adjusts Cut Position when cutting sprocket paper.

Selects auto line feed.

(Selects auto line feed by CR Code)

Selects Receive Buffer Size

Selects font

Selects conditions of BUSY

Selects enable/disable of print stop in Cover Open

Selects the paper width of Roll paper (Changes the print area)

Selects a zero font

Selects the paper length of Sprocket paper

Selects the paper sensor that enables Paper End Signal.

∙RNE: Receipt/Journal Near End Sensor

∙RE: Receipt/Journal End Sensor

Sets

OYes No

Yes(CMC-7)

Yes(E-13B)

ONo 0.25mm Right 0.20mm Right 0.15mm Right 0.10mm Right 0.05mm Right 0

0.05mm Left 0.10mm Left 0.15mm Left 0.20mm Left 0.25mm Left -1.75mm ~ +1.75mm *Can be set in the 0.35mm unit

*Default value: 0 mm -1.75mm ~ +1.75mm *Can be set in the 0.35mm unit

*Default value: 0 mm Yes

O No 2K

O 16K O Utility

HSD

O Yes (Off-line or receive buffer-full)

No (Receive buffer-full) O Yes

No

O 76.2mm 69.5mm Slashed

O Unslashed 88.9mm 139.7mm 215.9mm

O 279.4mm 304.8mm

O Yes (RNE or RE) Yes (RE)

No

Note 1) I/F control information (baud rate, etc.) and customer display connection/disconnection of serial model are set by DIP-SW on the I/F board.

Note 2) MICR Unit selection has the following two types for MICR Read test (Refer to Section 2.6): “Yes (CMC-7),” and “Yes (E-13B).” Normally, either selection is recognized as an actual installation status of MICR Unit, and MICR type is selected by designation of the command.

Note 3) For No. 3, 4, and 5, adjust to the proper values at factory shipment.

38 OKIPOS 425D

Image 38

Oki 425D manual OKI Standard Model, Hsd

Contents

Okipos 425D Web Site Mailing AddressMail Address Contents Troubleshooting and Repair Specifications Command Description Using the Unitool Printer Driver Where to install your printer Select a Location Unpacking Getting Started Installing the Printer Getting to Know the Okipos 425D Remove the Shipping Restraints Setting the Interface Board Assembly Setting the DIP Switches RS-232C Installing the Interface Board Assembly Connecting the Customer Display Connecting the ComputerConnecting the Cash Drawer Connecting the Power Installing the Ribbon Cartridge Unpack the ribbon cartridge Developer’s Guide English Installing the Paper Paper Specifications Maximum thickness 0.3 mm 0.012 inches Adjusting the Roll Paper Guide Receipt Roll paper Loading the Roll Paper Receipt Cut the roll paper Close the printer cover Adjusting the Roll Paper Guide Journal Loading the Roll Paper Journal Okipos 425D Adjusting the Roll Paper Near End Sensing Position Cut-Sheet Paper Slip Loading the Cut-Sheet Paper Slip Cut-Sheet Paper Validation/Stub Loading the Cut-Sheet Paper Validation/Stub How to remove the Piece Developer’s Guide English Sprocket Paper Tractor Loading the Sprocket Paper Tractor Developer’s Guide English Okipos 425D Developer’s Guide English Operation Panel Functions Operation Panel Switching Functions SW2 FF/LOD,PAK SW3 CUT SW1 LED OFF PowerLED Function LED Local Functions Types Starting SW2 SW3 SW1 SW4 Overview Menu Function ReceiptOEM Standard Model OKI Standard Model HSD Operation How to OperateStart Print Format How to PrintHex Dump Function Receipt Using the Micr Reader How to use the Micr Reader Micr Read Test Receipt Return code Status When Read is OKWhen Read is NG Rewinder Winding Evaluation Continuous Print Test Journal Using the Auto Cutter How to Use Maintenance Replacing the Ribbon Cartridge Important! Do not remove the ribbon shield 1 from the ribbon Developer’s Guide English Replacing the Roll Paper Roll Paper Receipt Roll Paper Journal Okipos 425D Clearing Paper Jams Print head may be very hot. Exercise caution Auto Cutter Developer’s Guide English Service Cut-Sheet Paper Sprocket Paper Troubleshooting and Repair Alarm Indication for a Failure Details of Alarm Indications Blink LED LED 1 Error LED 2 StatusLED Indication Scope of Application CharacteristicsIntroduction Options Configuration Environmental Conditions General SpecificationsPower Requirements Agency Approvals GND Communication Interface SpecificationsParallel Interface OKI/OEM Standard Type Dkstatus 2 RS-232C Interface OKI Standard Type RTS DSR DTR Init CASHDV2 Cash Drawer connector OKI Standard TypeCASHDV1 CASHST-N DTR DSR Printer Physical CharacteristicsPrinthead Selectable Character Pitches Logical CharacteristicsPrint Direction Maximum Number of Characters per Line Line Feed Pitches Printer PerformanceFont Size/Cell Size Print Speed Cut-Sheet Paper Counterfoil/Stub Media SpecificationsCut-Sheet Paper Slip/Validation Roll Paper Receipt/Journal Paper Size and Printing Area Appendix Media SpecificationsCut-Sheet Paper Slip/Validation Okipos 425D Developer’s Guide English Fixing Method of Multi-part Paper Joint Paper Weight and Maximum Duplicating QuantityPaper Quality Binding Holes Perforated Lines Provisions on Fold, Bend and Curl on Cut-sheet Paper Roll paper Receipt/Journal Paper Weight Sprocket Paper Tractor Developer’s Guide English Paper Quality D E Okipos 425D Rising in Horizontal Perforated Line Position Deviation of Sprocket Holes Binding Holes Corner Cut Wrinkle, Pleat and Swell Micr only with Micr Type Paper Size and Scanning Area Paper Positioning Restrictions Paper Feed SpecificationsPaper feed methods/Paths Paper Tear-off Micr Specifications Only with Micr type Cutting Specifications Auto Cutter SpecificationsRibbon Specifications Reliability HEX DEC Code DC2 Can ESC Control Code ListFunction Code ESC SI ESC DLE D ESC SequenceHEX 1B OD ESC ESC @ US Sequence GS sequenceHEX HEX DEC Code DC2 Can DLE ESC DLE Sequence ESC Data FS Sequence GS ENQ 1.1 USA Character SetCode table OEM Standard Type Canada-French Multilingual Portugal Norway Brascii Abicomp Multilingual ISO 8859/15 International character set table Code table OKI Standard Type 2.1 USA Canada-French Multilingual Portugal Norway Brascii Abicomp Multilingual ISO 8859/15 International character set table Using the Unitool Printer Driver Setting Slip Paper in the Paper Tray Using Registered Paper Icons Okipos 425D Developer’s Guide English Using Custom Size Using Paper Size that is less than 187.96 mm 7.4 in Width Image of actual printing area Example Developer’s Guide English Okipos 425D Developer’s Guide English Symbol Designation Standard Value About the Validation Printing Area Data in application Print result Example Setting Tractor Paper in the Tractor Unit Orientation Okipos 425D Developer’s Guide English