Manuals / Oki / Computer Equipment / Printer

Oki 425D manual Rewinder Winding Evaluation Continuous Print Test Journal

Models: 425D

1 137

Download 137 pages 30.02 Kb

Page 45

2.7 Rewinder Winding Evaluation Continuous Print Test (Journal)

This function performs print/platen switch continuous test to evaluate the rewinder winding performance.

(1)How to start

Turn the power on while holding down SW3 + SW1 + SW4.

(2)How to exit

Turn the power off.

•During test printing, if you press SW1, printing suspends. If you press SW1 again, printing resumes.

(3)Contents printed

(a)Prints “HHH”+ Space + “HHH” (UTL characters)

(b)Print Sheet Mode switching (Journal ÆSlip ÆJournal)

Developer’s Guide: English 45

Image 45

Oki 425D manual Rewinder Winding Evaluation Continuous Print Test Journal

Contents

59336301 OKIPOS 425D Developer’s GuideDisclaimer Document Title and Part NumberCopyright Information Contact InformationContents Specifications Troubleshooting and RepairUsing the Unitool Printer Driver Command Description1. Setting Up the Printer 1.2 Where to install your printer1.1. Select a Location 1.3 Unpacking Getting StartedDeveloper’s Guide English 1.4 Installing the Printer Getting to Know the OKIPOS 425D8 OKIPOS 425D 1.4.1 Remove the Shipping Restraints 1.4.2 Setting the Interface Board Assembly 1.4.2.1 Setting the DIP Switches RS-232CDIPSW1 DIPSW2 1 Insert the Interface Board Assembly in the direction of the arrow 1.4.2.2 Installing the Interface Board Assembly2 Secure the Interface Board Assembly with 2 screws Developer’s Guide English1.4.4 Connecting the Cash Drawer 1.4.3 Connecting the Computer1.4.5 Connecting the Customer Display 1.4.6 Connecting the Power1. Make sure the printer is turned OFF 1.4.7 Installing the Ribbon Cartridge2. Press the Cover open bar and open the printer cover 3. Center the printhead4. Unpack the ribbon cartridge 5. Install the new ribbon cartridge1 Ribbon Shield 2 Take-up Knob 3 Grip Points 1 Hold the ribbon cartridge as shown below3 Lower the front of the cartridge over the printhead until it snaps into place Note 2 The standard paper weight is 57g/m2 15lb 1.5 Installing the PaperNote 1 All part must be glued at the top. Multipart is slip only 16 OKIPOS 425D1.5.1.1 Adjusting the Roll Paper Guide Receipt 1.5.1 Roll paper1.5.1.2 Loading the Roll Paper Receipt Note The printer must be turned on before installing the roll paperDeveloper’s Guide English 5. Cut the roll paper 6. Close the printer cover20 OKIPOS 425D 1.5.1.3 Adjusting the Roll Paper Guide Journal1.5.1.4 Loading the Roll Paper Journal Note The printer must be turned on before installing the roll paper4 Mount the rewinder on the printer 1.5.1.5 Adjusting the Roll Paper Near End Sensing Position 1.5.2 Cut-Sheet Paper Slip 1.5.3 Cut-Sheet Paper Validation/Stub 1.5.3.1 Loading the Cut-Sheet Paper Validation/StubDeveloper’s Guide English How to remove the Piece CAUTION Printhead may be very hot26 OKIPOS 425D 4. Close Printer Cover Paper has been set for long-edge printing Store the removed Piece in a safe place so that you will not lose itDeveloper’s Guide English Note The printer must be turned off before inserting the tractor 1.5.4 Sprocket Paper Tractor3. Set the tractor lever 1 in the direction of the arrow 4. Turn on the printerDeveloper’s Guide English 30 OKIPOS 425D 10. Preparation 2. Using the Printer 2.1 Operation Panel FunctionsOperation Panel 2.1.1 Switching Functions 34 OKIPOS 425D 2.1.2 LED Function2.2.1 Types 2.2 Local Functions2.2.2 Starting 2.3 Menu Function Receipt 2.3.1 OEM - Standard ModelOverview 38 OKIPOS 425D 2.3.2 OKI - Standard Model2.3.3 How to Operate StartOperation 2.4.2 How to Print 2.4 Hex Dump Function Receipt2.4.1 Print Format 1 Sheet Guide 2.5 Using the MICR ReaderHow to use the MICR Reader 2.6 MICR Read Test Receipt When Read is NG When Read is OKread command Return code2.7 Rewinder Winding Evaluation Continuous Print Test Journal How to Use 2.8 Using the Auto Cutter3. Maintenance 3.1 Replacing the Ribbon CartridgeDeveloper’s Guide English Caution! The printhead may be HOT Important! Do NOT remove the ribbon shield 1 from the ribbon48 OKIPOS 425D Developer’s Guide English 3.2 Replacing the Roll Paper 3.2.1 Roll Paper Receipt50 OKIPOS 425D 3.2.2 Roll Paper Journal Arrow 3 Wide Roll Paper Width 76.2 mm 3.3 Clearing Paper Jams Print head may be very hot. Exercise cautionDeveloper’s Guide English Auto Cutter 2. Remove the rewinder and cut the paper at the positions Cut-Sheet Paper Sprocket Paper 4. Troubleshooting and Repair 4.1 Alarm Indication for a FailureOperation Panel 4.1.1 Details of Alarm Indications 1 One CycleDeveloper’s Guide English 60 OKIPOS 425D 4.1.2 LED Indication5.1.2 Characteristics 5. Specifications5.1 Introduction 5.1.1 Scope of ApplicationOnly one interface option can be installed Options62 OKIPOS 425D Standard Printer Configuration 1 Printer Cover 2 Control Panel 5.1.3 Configuration3 Paper Guide 4 Cover Open Bar 5 ON/OFF Switch Developer’s Guide English5.2.1 Power Requirements 5.2 General Specifications5.2.2 Environmental Conditions 5.2.35.3.1 Parallel Interface OKI/OEM Standard Type 5.3 Communication Interface SpecificationsNote 1 Connector pin arrangement 5.3.2 RS-232C Interface OKI Standard TypeNote Pin arrangement 5.3.3 Cash Drawer connector OKI Standard TypeDeveloper’s Guide English 1 2 3 4 5Pin arrangement 5.3.4 Customer Display connector OKI Standard RS-232C Interface Type5.4 Physical Characteristics 5.4.1 Printhead5.4.2 Printer 5.5.1 Print Direction 5.5 Logical Characteristics5.5.2 Selectable Character Pitches 5.5.3 Maximum Number of Characters per Line5.5.4 Font Size/Cell Size 5.6 Printer Performance5.5.5 Line Feed Pitches 5.6.1 Print Speed5.7.1 Cut-Sheet Paper Slip/Validation 5.7 Media Specifications5.7.2 Cut-Sheet Paper Counterfoil/Stub 5.7.3 Roll Paper Receipt/Journal5.7.5.1.1. Paper Size and Printing Area 5.7.5 Appendix Media Specifications74 OKIPOS 425D Note 1 The height-width ratio must be 1 2/3 5.7.5.1.2 Paper Quality 5.7.5.1.3 Paper Weight and Maximum Duplicating Quantity5.7.5.1.4 Fixing Method of Multi-part Paper Joint 76 OKIPOS 425D5.7.5.1.5 Binding Holes 5.7.5.1.6 Perforated Lines 5.7.5.1.7 Provisions on Fold, Bend and Curl on Cut-sheet Paper 5.7.5.2.1 Paper size and Printing area 5.7.5.2. Roll paper Receipt/Journal5.7.5.2.3 Paper Weight Note 1 The standard paper weight must be 57g/m2 15 lb5.7.5.2.2 Paper Quality 5.7.5.3. Sprocket Paper Tractor 5.7.5.3.1 Paper size and Printing area82 OKIPOS 425D Note 2 The print quality on the last page is not warrantied 5.7.5.3.3 Paper Weight and Maximum Duplicating Quantity 5.7.5.3.2 Paper Quality84 OKIPOS 425D B C D E 5.7.5.3.4 Fixing Method of Multi-part Paper Joint86 OKIPOS 425D 5.7.5.3.6 Position Deviation of Sprocket Holes 5.7.5.3.5 Rising in Horizontal Perforated Line88 OKIPOS 425D 5.7.5.3.7 Binding Holes5.7.5.3.8 Corner Cut 5.7.5.3.9 Wrinkle, Pleat and Swell 5.7.5.4.2 Paper Weight 5.7.5.4. MICR only with MICR Type5.7.5.4.1 Paper Size and Scanning Area 5.8.1 Paper feed methods/Paths Paper Feed Specifications5.8.2 Paper Positioning Restrictions 5.8.3 Paper Tear-off5.9.6 Media Specifications 5.9 MICR Specifications Only with MICR type5.9.1 Available Fonts 5.9.2 Scanning Speed5.11 Ribbon Specifications 5.10 Auto Cutter Specifications5.12 Reliability Cutting Specifications6. Command Description 6.1 Control Code List6.1.1 OEM - Standard Model 96 OKIPOS 425D 6.1.1.2 ESC SequenceHEX 1F 0E 1F 0E 1F 0E 1F 0E 1F 0E 1F 0E 1F 0E 1F 0E 1F 0E 1F 0E DLE Sequence 6.1.2 OKI Standard Model6.1.2.2 ESC Sequence 1B 6D 1B 1B 1B 1B 1B 1B 7A 1B 10 1B 10 6.1.2.4 GS Sequence 6.1.2.3 FS Sequence6.2.1 Code table OEM - Standard Type 6.2 Character Set6.2.1.1 USA 102 OKIPOS 425D1 0xH and 1xH are Control Code areas 6.2.1.2 Canada-French4 The blank space 20H, 7FH, FFH indicates a space code Developer’s Guide English104 OKIPOS 425D 6.2.1.3 Multilingual1 0xH and 1xH are Control Code areas 6.2.1.4 Portugal4 The blank space 20H, 7FH, FFH indicates a space code Developer’s Guide English106 OKIPOS 425D 6.2.1.5 Norway1 0xH and 1xH are Control Code areas 6.2.1.6 BRASCII4 The blank space 20H, 7FH, A0H indicates a space code 5 8xH and 9xH are ignored. Shaded areas108 OKIPOS 425D 6.2.1.7 Abicomp1 0xH and 1xH are Control Code areas 6.2.1.8 Multilingual4 The blank space 20H, 7FH, FFH indicates a space code Developer’s Guide English110 OKIPOS 425D 6.2.1.9 ISO 8859/15Developer’s Guide English 6.2.1.10 International character set table6.2.2 Code table OKI - Standard Type 6.2.2.1 USA112 OKIPOS 425D 1 0xH and 1xH are Control Code areas 6.2.2.2 Canada-French4 The blank space 20H, 7FH, FFH indicates a space code Developer’s Guide English114 OKIPOS 425D 6.2.2.3 Multilingual1 0xH and 1xH are Control Code areas 6.2.2.4 Portugal4 The blank space 20H, 7FH, FFH indicates a space code Developer’s Guide English116 OKIPOS 425D 6.2.2.5 Norway1 0xH and 1xH are Control Code areas 6.2.2.6 BRASCII4 The blank space 20H, 7FH, A0H indicates a space code 5 8xH and 9xH are ignored. Shaded areas118 OKIPOS 425D 6.2.2.7 Abicomp1 0xH and 1xH are Control Code areas 6.2.2.8 Multilingual4 The blank space 20H, 7FH, FFH indicates a space code Developer’s Guide English120 OKIPOS 425D 6.2.2.9 ISO 8859/15Page 7.1 Setting Slip Paper in the Paper Tray 7. Using the Unitool Printer Driver7.1.1 Using Registered Paper Icons 1 Printing area 2 Printable Maximum Width 160.02mm 6.3 inch 2 Paper Width is less than 190.5 mm 7.1.2.1 Using Paper Size that is less than 187.96 mm 7.4 in Width 7.1.2 Using Custom SizeImage of actual printing area 128 OKIPOS 425D Example1 Target Printing Area 2 Printing Area with margin adjusted 3 Right Margin 27.94mm 1.1 inch 4 Slip Tray Left Side 5 Paper Guide 1 Target Printing Area 2 Printable Maximum Width 160.02mm 6.3 inch6 Slip Tray Right Side 130 OKIPOS 425DPage Symbol 7.2 About the Validation Printing AreaDesignation Standard ValueData in application 7 RAlignment is used 8 When spaces are inserted x x spacePrint result 1 Center Line 2 LAlignment is used 3 Center is used134 OKIPOS 425D Example7.4 Orientation 7.3 Setting Tractor Paper in the Tractor Unit136 OKIPOS 425D 7.5 Special functions of the Windows 95/98 Version Printer DriverNormally, you need not change, but use this function as needed